1. DL manuals
  2. Gaggenau
  3. Oven
  4. VG 411
  5. Operation, Maintenance And Installation Manual

Gaggenau VG 411 Operation, Maintenance And Installation Manual

Summary of VG 411

  • Page 1

    Operation, maintenance and installation manual vg 411 gas cooker.

  • Page 2

    1 vg 411 1. Important notes page 3-4 for your safety page 3 operating for the first time page 3 about use page 4 2. Features page 5 features of the appliance page 5 control knob page 5 burner parts page 5 3. Operating principle page 6 4. Operation page 7 5. Settings table page 8 6. Cookware recommen...

  • Page 3

    2 congratulations on buying your new “vario” appliance. Before switching your appliance on for the first time, we would like you to familiarize yourself with your new appliance. In this manual you will find important notes on safety and operation. These will serve to ensure your personal safety and ...

  • Page 4

    For your safety you must not operate the appliance if it is damaged. When connecting electrical appliances in the proxi- mity of the appliance, make sure that connecting leads do not come into contact with hot cooking surfaces! As the user, you yourself are responsible for maintenance and proper use...

  • Page 5

    About use the appliance is intended solely for use in the household and must not be put to any other uses. Use the appliance to prepare meals only. It must not be used to heat up the room in which it is installed.! Use of a gas cooker generates heat and humidity in the room where it is installed. Th...

  • Page 6

    Features of the appliance control knob burner parts 1 ventilation openings 2 large (wok) burner 5 kw 3 pot grid flame setting: 0 off high setting of outer and inner flame ring low setting of outer flame ring high setting of inner flame ring outer flame ring off high setting of inner flame ring outer...

  • Page 7

    3. Operating principle 6 the appliance features one-hand operation, flame detection and automatic re-ignition. The ignition is activated when the control knob is turned. Should the flame go out during operation, the appliance will automatically re-ignite the burner. During a disturbance, the applian...

  • Page 8

    7 switching on • place a suitable pot or a pan on the cooking position. • press down the control knob and turn it to the required position between the and symbols. The burner ignites automatically. • when using large pots or pans you should ignite the burner in the low position. • every time the gas...

  • Page 9

    8 5. Settings table cooking cooking method examples level high boiling water searing meat heating fat, liquids boiling soup, sauce blanching vegetables roasting meat, fish, potatoes from browning flour, onions roasting almonds, breadcrumbs baking pancakes, egg dishes to boiling in open pot liquids s...

  • Page 10

    Pots with a diameter of less than 160 mm or more than 320 mm should not be used. When using large pots, pay attention to keeping to a minimum distance of 50 mm between the cooking vessel and combustible surroundings. When buying pots, pay attention to the fact that the manufacturer frequently specif...

  • Page 11

    The wok and accessories (not included in the scope of delivery) – the round-bottom wok is the ideal wok for your gas cooker. – the wok looks like a hollow semisphere with a long handle or wooden handle. It has a rounded base and slanted sides. The thin steel passes the heat swiftly to the inside, bu...

  • Page 12

    11 keep the ventilation openings on the rear of the appliance clean. Do not block the ventilation openings. The burner (burner head cover and burner ring) will change the color during operation and become darker. This change in color will not influence the use-value. Please thoroughly clean the appl...

  • Page 13

    12 part / material suggested cleaning procedure important reminders pot grid take pot grids off for cleaning. Do not clean in a dishwasher. (enamel on soak in sink. Soak burnt-in remainders in sink. Cast iron) clean with detergent and brush. Abrasive cleaners, used too vigorously or too often can ev...

  • Page 14

    The appliance must be disconnected from the power and gas supply during all repair work. In the event of malfunctions, check whether the gas and electricity supplies are in proper working order. The cooktop cannot be used during a power failure. If the cooktop is being used when the power failure oc...

  • Page 15

    14 10. Trouble shooting no electrical power switch the appliance on again. Should the appliance still not work, contact your gaggenau after-sales service. Burner does not ignite when switched on overheating protection wait, until the appliance has cooled and the signal goes off turn control knob to ...

  • Page 16

    15 technical data (gas) burners: full burning 5 kw low burning 0.3 kw gas connection: r 1/2’’ union nut for r 1/2’’ bracket to din 1999, conical-cylindrical technical data (electrical) rated consumption 15 w voltage 220-240 v frequency 50-60 hz technical modifications reserved. 11. Technical data / ...

  • Page 17

    Important notes please observe the general safety notes and the important information in chapter 1. The installing technician is responsible for perfect functioning of the appliance at its installa- tion location. He must show the user how to switch off the electricity and gas supply whenever requir...

  • Page 18

    17 connecting the appliance electrical connection electrical connection (ac 220-240 v) is established by means of a connecting cable with an earthing contact plug connected to an earthed socket, which must also be accessible after installation of the gas hob. If, after installation of the gas hob, n...

  • Page 19

    Preparing the cabinet • cut out the recess for the hob in your worktop. Proceed as indicated on the installation sketch. The installation sketch contains the measurements of the space required for the trim between the appliances. Several appliances can also be installed in individual recesses, as lo...

  • Page 20

    Installing the cooker please note: if you want to convert the appliance to a different type of gas, change the nozzles before installing the appliance (see pages 22 - 23). • before installation, remove all styrofoam packaging from the control knob and peel off the protective film. • hold the support...

  • Page 21

    Installing the spindle the numbers correspond to the diagram on the opposite page. Spindle extensions (sv 401-090 / sv 401-205) are available should the appliance be installed in a worktop which is non-standard depth. Loosen the nuts of the spindle cover and remove cover. 1 insert the spindle from b...

  • Page 22

    21.

  • Page 23

    22 nozzle replacement changing over to a different gas type only authorised specialists are permitted to change over to a different gas type. The nozzles needed for the gas type to be set are available as a conversion kit. Please specify the appliance type and the required gas type. The nozzles can ...

  • Page 24

    Replacing the main burner nozzles of the wok-burner • unscrew the wok burner from the trough (torx t20). Loosen locking screw from the air regulation bush. Fully push in the air regulation bush. Detach the safety springs on the supply line. Leave the electrode connected. • carefully pull off the wok...

  • Page 25

    Gaggenau hausgerÄte gmbh carl-wery-str. 34 · d-81739 mÜnchen y (089) 45 90-03 fax (0 89) 45 90-23 47 www.Gaggenau.Com en.