Galletti EXCELIA MXE 009 Manual - Mxe
RG66004088 - Rev 00
MXE
All copying, even partial, of this manual is strictly forbidden.
Serie
Grandezza
Organismo Notificato
N° certificato
Procedura di valutazione di conformità Categoria PED Marcatura
Range
Size
Notified body
certificate
Conformity Compliance Module
PED category
Marking
ECH
2
O - ECH
2
O H
4-5-6-7
1115
Modulo D1
I
CE
MCA - MCA H
10-12-14
1115
Modulo D1
I
CE
MCA - MCA H
16-21-25-30-37-50-60
1115
Modulo D1
II
CE + PED
LCA - LCA H
045-050-060-070-080-090-105
1115
Modulo D1
II
CE + PED
MCC - MCC H
6-7-9-12-15
1115
Modulo D1
I
CE
MCC - MCC H
18-22-25-33-37
1115
Modulo D1
II
CE + PED
MCW - MCW / H
5-7-10-12-15
1115
Modulo D1
I
CE
MCW - MCW / H
18-20-22-27-31-39
1115
Modulo D1
II
CE + PED
MPE - MPEH - MCE - MCEH
4-5-7-8
1115
Modulo D1
I
CE
MPE - MPEH - MCE - MCEH
9-10-11-13-15-18
1115
Modulo D1
I
CE
MPE - MPEH - MCE - MCEH 19-20-21-23-24-26-27-28-31-32-34-35-39-40
1115
Modulo D1
II
CE + PED
MPE - MPEH - MCE - MCEH
T30-T34-T40-T45
1115
Modulo D1
II
CE + PED
MFE
5-6-8-11-13-16-17-20-23
1115
Modulo D1
I
CE
MXE
9-11-14-16 1115
Modulo
D1
I
CE
MXE
19-21
1115
Modulo D1
II
CE + PED
LCA - LCA H
115-130-150-180-205-220-235-250-280-300
0398
B.05.0600AP-01 - 01-01-2005
Modulo D1
II
CE + PED
N°
006 r
ev
. 4 d
el 06/02/2008
LCA and LCA H (115-300) units are manufactured in the plants of Hiref S.p.a - Galletti Group, Viale Spagna 31/33 Tribano (Padova)
Bentivoglio, 16/07/2008
Galletti S.p.A.
Luigi Galletti
President
DECLARATION OF CONFORMITY
Galletti S.p.A., whose head office is located at 12/a Via Romagnoli 12/a Bentivoglio (Bologna) - Italy, hereby declares, under its own responsibility, that
the water chillers and heat pumps belonging to the series:
ECHO, ECHO H, MCA, MCA H, LCA, LCA H, MCC, MCC H, MCW, MCW-H, MPE, MPEH, MCE, MCEH, MFE and MXE, units intended for applications
in civil air conditioning systems, comply with the requirements of EEC Directives 98/37/CE, 89/336/CEE, 92/31/CEE, 93/68/CEE, 2006/95/CE,
97/23/CE (PED).
These units are the result of an assembly of components [compressors, brazed plate heat exchangers, liquid receivers, pipes, control and safety
valves] which are individually provided, where required, with certification in accordance with current directives: the category to which the machines
belong is determined on the basis of an analysis of the components subject to the PED and corresponds to the highest category among the
components used.
For each series of machines, the conformity of the assembly has been assessed by notified bodies, applying the assessment procedures (forms)
pursuant to annex II of the PED - Directive 97/23, as shown in the following table: