- DL manuals
- Gamma
- Stringing Machines
- 6004
- Owner's Manual
Gamma 6004 Owner's Manual
Summary of 6004
Page 1
Copyright 2000 gamma sports - all rights reserved o o o o owner's manu wner's manu wner's manu wner's manu wner's manual al al al al issue 3 - december 14, 2000 issue 3 - december 14, 2000 issue 3 - december 14, 2000 issue 3 - december 14, 2000 issue 3 - december 14, 2000 6004 stringing machine.
Page 2: 6004
1 6004 stringing machine table of contents page 1 ................................................................................... Warranty page 2 ..................................................................................... Features page 3 ...................................................
Page 3: Machine Features
2 ! Manual spring tensioner ! Diamond coated string gripper ! Tension range: 11lbs. - 89lbs. ! 6 point suspension mounting system ( 10 point support ) ! Cam-lock dual action composite string clamps w/ diamond coating ! Full 360 degree turntable rotation ! Precision bearing mounted turntable ! Large ...
Page 4: Assembly Instructions
3 align the holes in the leg flange with the matching holes in the lower column support post. Secure the leg with one flat head cap screw through the upper hole, and one socket head cap screw through the bottom hole. Repeat this procedure for the three remaining legs. Upper column support assembly i...
Page 5: Assembly Instructions
4 assembly instructions tension track installation place the tube of the tension track assembly over the top of the upper column support. Align the tension track with the long leg of the base assembly. Securely tighten the two socket set screws on the tension track assembly tube, locking it to the u...
Page 6: Assembly Instructions
5 assembly instructions turntable installation position the recess in the underside of the turntable over the flange of the turntable pin. Frame support post installation the support post assemblies are precision aligned at the factory and are marked for proper installation on the turntable. Install...
Page 7: Assembly Instructions
6 assembly instructions clamp head installation the post of the string clamp head and the tube of the string clamp base are treated with grease to provide protection against corrosion during shipping. Remove any excessive grease with a clean cloth prior to use. The post and tube may also be cleaned ...
Page 8: Assembly Instructions
7 travel stop assembly instructions note : the tensioner bar is equipped with a tensioner travel stop to limit travel of the tensioner along the bar and prevent contact between the tensioner and the racquet mounting system while stringing. The travel stop is located about midpoint along the tensione...
Page 9: Mounting The Frame
8 frame support post adjustment place the racquet frame over the center support slide and onto the frame support. Loosen the lever lock bolt on one support post. Slide the post outward until the center support of the racquet support slide is positioned near the inside surface of the racquet frame. S...
Page 10: Mounting The Frame
9 securing the shoulder supports secure the racquet frame with the shoulder supports by rotating the large adjustment knobs on the outside of the support post assemblies clockwise. Adjust the supports until firm contact is made between the shoulder supports and the frame. The tear drop shaped holes ...
Page 11: Stringing The Frame
10 stringing the frame setting tension the gamma 6004 utilizes a rotary adjusting knob along with a linear tension scale to indicate the tension setting. The scale is divided into 3 lb increments and each 1/3 turn of the tension knob changes tension by 1 lb. To set the desired tension, rotate the te...
Page 12: Stringing The Frame
11 pulling tension wrap the loose section of string once around the roller and insert the string between the diamoind dust coated string gripper plates. Pull the string perpendicular to the gripper plates while slowly rotating the tensioner crank clockwise until the brake lever pops out of the latch...
Page 13: Pathfinder Awl
12 the gamma 6004 includes the new pathfinder string- ing awl which creates a pathway between or around strings and through tight grommets. Insert the awl through the grommet hole in the same manner as for traditional awls. The pathfinder awl must be closed before insertion. Once the awl is inserted...
Page 14: Maintenance and Adjustments
13 tension calibration procedure step 1 set the tension to 60 lbs. As indicated by the linear scale and rotary knob. Place the string on one end of a tension calibrator into a string clamp and secure. Place string located on the other end of the calibrator into the string tensioner and apply tension...
Page 15: Maintenance and Adjustments
14 adjusting the tensioner brake step 1 after stringing many racquets, the brake of the tensioner may need to be adjusted. With the brake lever engaged, loosen the lock bolt located on the back side of the tensioner frame with the 4mm hex wrench. Note: the lock bolt should only be loosened enough to...
Page 16: Maintenance and Adjustments
15 maintenance and adjustments the cam-lock cam-lock cam-lock cam-lock cam-lock clamps will need minor adjustments according to what string type, construction, and gauge you are using. To adjust the gap (clamping pressure) between the clamp jaws, insert the string through the racquet as if you were ...
Page 17: Maintenance and Adjustments
16 maintenance and adjustments turntable brake pad replacement loosen the four set screws located at the top of the turntable tube until the turntable and turntable flanged pin can be lifted from the support tube. Insert the 2.5 mm l-shaped wrench into the flat head screw located on the inner side o...
Page 18: Troubleshooting Tips
17 problem solution string slips in clamps string slips in gripper for additional assistance, contact customer service - adjust gap between jaws - clean clamp jaws - clean gripper jaws - adjust gripper jaw stop screw troubleshooting tips string clamp base slips on turntable. - adjust base locking le...
Page 19: Component Identification
18 component identification 9 6b 104a 111 117 112 114 113 116 120 119 115 121 180 193 194 195 201 203 178 204 173 205 134 133 132 13 14 135 139 136 122a 21a 23a 21b 22a.
Page 20: Parts List
19 parts list part # 6b 9 13 14 21a 21b 22a 23a 104a 111 112 113 114 115 116 117 119 120 121 122a 132 133 134 135 136 139 173 178 180 description cap screw - m8x30 washer - m8 post lock lever washer - m10 frame support - tennis frame support - bad. Badminton adapter - blk tennis adapter - black tens...