1. DL manuals
  2. Gamma
  3. Stringing Machines
  4. 6004
  5. Owner's Manual

Gamma 6004 Owner's Manual

Other manuals for 6004: Owner's Manual, Owner's Manual, Owner's Manual
Manual is about: 2 POINT SC MOUNTING

Summary of 6004

  • Page 1

    Owner’s manual issue 11a - february 2014 stringing machine 6004 6 point sc mounting.

  • Page 2: 6004

    2 table of contents warranty ............................................................................................... Page 2 features.................................................................................................. Page 3 package contents.........................................

  • Page 3: Machine Features

    3 machine features machine features manual spring tension winder with 11 to 89 lbs tension range patented roller guide for maximum accuracy and consistency parallel jaw gripper with diamond dust coated gripping sur- faces professional six point self-centering “suspension mount” rac- quet mounting sy...

  • Page 4: 6004

    4 6004 unpacking instructions & contents instructions for unpacking and preparing for assembly the stringing machine is shipped in two cartons, a master carton has the stringing machine fl oor stand, base legs, tensioner and accessories. The mounting system carton has the turntable, clamps and mounti...

  • Page 5: Assembly  Instructions

    5 assembly instructions base leg assembly the stringing machine uses a four leg base design. The legs must be assembled to the lower column support before use. This is the larger of the two posts with the gamma label. Align the holes in the leg fl ange with the matching holes in the lower column supp...

  • Page 6: Assembly  Instructions

    6 assembly instructions bellows installation the bellows assembly is supplied in two pieces and should be assembled as follows. Place the bellows section with the fl ange over the upper support column with the fl ange on the top. Place the remaining bellows over the upper support column and mate it wi...

  • Page 7: Assembly  Instructions

    7 assembly instructions turntable and mounting system installation to install the turntable position the turntable over the turntable pin and align the bolts, located in the poly bag, with the holes in the fl ange. Secure them with the included hex wrench. String clamp installation the post of the st...

  • Page 8: Assembly  Instructions

    8 assembly instructions mounting the frame mounting stand adjustment to adjust the spacing between the mount- ing stands, turn one of the knobs located at either end of the turntable. There is an arrow on the face of each knob indicating the turning direction that will “tighten” the mount- ing point...

  • Page 9: Mounting  The  Frame

    9 frame shoulder support adjustment the shoulder supports are designed to rotate and can be adjusted to provide maximum support to the racquet frame. Rotate the support so that the pads contact the frame squarely when the arms are closed against the racquet. Should the shoulder supports block string...

  • Page 10: Stringing  The  Frame

    10 setting tension the spring tensioner utilizes a rotary adjust- ing knob along with a linear tension scale to indicate the tension setting. The scale is divided into 3 lb. Increments and each 1/3 turn of the tension knob changes tension by 1 lb. To set the desired tension, rotate the tension knob ...

  • Page 11: Stringing  The  Frame

    11 getting started to begin stringing the main strings, thread the two ends of the string through the two center holes at the appropriate end of the frame and continue through the opposite center holes. Thread one end of the string through the adjacent grommet hole and pull excess by hand. Secure on...

  • Page 12: Stringing  The  Frame

    12 weaving the cross strings weave the cross strings over and under the main strings being careful to alternate the weave direction of each consecutive cross string so as to be opposite of the previously installed cross string. Once the fi nal cross string is tensioned and clamped, tie off at the app...

  • Page 13: Pathfinder  Awl

    13 pathfinder awl once the awl is inserted, pull the handle of the awl outward while holding the tip section in place. This leaves the outer sheath in the grommet hole. Insert the end of the string into the outer sheath. While holding the string, slowly pull the sheath out of the grommet hole to lea...

  • Page 14: Maintenance & Adjustments

    14 b a maintenance & adjustments if the lever releases before 60 lbs., using the supplied l-shaped hex wrench, turn the adjustment screw (b) located on the left side of the latch block counter-clockwise to increase the engagement of the brake release latch with the brake lever. Repeat step 1 and adj...

  • Page 15: Maintenance & Adjustments

    15 maintenance & adjustments adjusting the tensioner brake after stringing many racquets, the brake of the tensioner may need to be adjusted. With the brake lever engaged in the latch, insert the 5mm allen wrench into the bolt (a) located at the base of the brake lever. It can be accessed through th...

  • Page 16: Maintenance & Adjustments

    16 maintenance & adjustments adjustment knob string clamp adjustment the string clamps will need minor adjust- ments according to string type, construction, and gauge. To adjust the gap (clamping pressure) between the clamp jaws, insert the string through the racquet as if you were beginning the mai...

  • Page 17: Troubleshooting  Tips

    17 troubleshooting tips care & cleaning with time and use, the clamping surfaces of your machine may become oily or dirty and result in string or clamp slippage while stringing. Periodic cleaning of the string clamps, string clamp base and string gripper is recommended. Knife sharpening stones work ...

  • Page 18: Parts  List

    18 parts list 6b cap screw- m8x30 104a tensioner assembly 105 retainer screw 112 tool tray 113 long leg 114 short leg 115 flat head screw- m8x25 116 lower column support 119 bellows 120a upper column support 121 leveling foot 140 mtng stand top plate 144 shlder supp lock knob 146a mtng arm adjust kn...

  • Page 19: Parts Drawing

    19 mdcsc13 msac11 parts drawing 121 115 114 113 320 112 119 337 327 336 6b 165 285 283 286 289 304 361 386 105 120a 165 mfspp13 340 mbmsp11 mmspp13 104a 116 140 144 146a 384 371 341 385 383.

  • Page 20: Gamma Sports

    Gamma sports 200 waterfront drive pittsburgh, pennsylvania 15222 phone: 800.333.0337 fax: 412.323.0317 visit our website at www.Gammasports.Com copyright 2014 gamma sports - all rights reserved mmu2-89 (mg63-17).