602fc 602fc 602fc 602fc 602fc o o o o owner's manu wner's manu wner's manu wner's manu wner's manual al al al al issue 1 - april, 2000 issue 1 - april, 2000 issue 1 - april, 2000 issue 1 - april, 2000 issue 1 - april, 2000 progression copyright 2000 gamma sports - all rights reserved stringing ma st...
1 table of contents table of contents table of contents table of contents table of contents page 1 ................................................................................... Warranty page 2 ..................................................................................... Features page 3...
2 features ! Drop weight tensioner w/ 8lb. To 90lb. Range and permanently engraved weight scale ! Professional six point “quick mount” racquet mounting system - accomodates all racquets without adapters ! Patented parallel jaw rotating ratchet gripper w/ diamond dust coated gripping surfaces - u.S. ...
3 assembly instructions installing the turntable the turntable is located under the foam packing in the bottom of the shipping carton. Insert the center post of the turntable into the bushing of the stringing machine base. Engaging the drop weight bar stop the stringing machine is shipped with the d...
4 assembly instructions fixed clamp installation to install the clamps, remove the winged lock knob to separate the knob from the lower guide bushing. Be careful not to lose the radial thrust bearing components located in the center recess of the knob. Align the clamp base with the clamp slot of the...
5 mounting the frame frame shoulder support adjustment being sure the shoulder supports are free to swivel in their mountings, simultaneously rotate the shoulder support adjustment knobs clockwise until both shoulder supports gently and squarely contact the frame. Tightening the center supports tigh...
6 securing the frame lock the shoulder supports in position by turning the knob at the base clockwise. Repeat the adjustment procedure for the remaining support post. Re-tighten all of the frame supports in the same order as before. Do not overtighten any of the supports as racquet damage may occur....
7 stringing the frame the drop weight is of a two piece design. When assembled, it will accomodate tensions from 20 lbs. To 90 lbs. For tensions from 8 to 20 lbs., remove the 5mm bolt on the face of the drop weight, and use the smaller portion of the weight as described above. Note: note: note: note...
8 stringing the frame fixed clamp operation the fixed clamps for the gamma 600fc are of a dual action design. The string clamp and the clamp base operate independently of one another. To clamp a string, lift the clamp head and place the string between the jaws. Depress the clamp head lever to secure...
9 stringing the frame warning: to avoid injury, keep fingers away from grip- per jaws while tensioning string. Pulling tension while securely holding the string gripper drum with your hand, lift the tension bar above horizontal and gently lower the bar under its own weight. If the tension bar drops ...
10 clamping the first main string secure the tensioned main string using the remaining fixed clamp. Repeat the procedure for all of the remain- ing main strings and tie off following the racquet manu- facturers recommendations. Follow the manufacturer's recommended stringing pat- tern for one or two...
11 pathfinder awl the progression 600fc includes the new pathfinder stringing awl which creates a pathway between and around strings to make inserting a string through tight grommets easier and quicker. Insert the awl through the grommet hole in the same manner as for traditional awls. The pathfinde...
12 maintenance your gamma 600fc stringing machine is adjusted for optimum performance at the factory and needs no further adjustments before use. After extensive use however, the machine may need minor adjusments as follows : adjusting the clamp pressure the clamps provided with your stringing machi...
13 care and cleaning with time and use, the clamping surfaces of your machine may become oily or dirty and result in string or clamp slippage while stringing. Periodic cleaning of the following parts is recommended. String clamps clean the inside gripping surfaces of the string clamp jaws by inserti...
14 exploded parts view.
15 parts list tools and accessories part # 4 5 6 7 8 9 10a 13 14 15a 21 22 23 24 25 25a 26 27 28 29 30 30a 31 32b 33b 34 35 36 37 40 53 54 55 56 description turntable bushing rubber feet cap screw foot nut bushing set screw washer - m8 winder stand - b/s post lock lever washer - m10 2021 support pos...
