Garland XG24-JIB Installation and operation manual - Operation
Part # 4523133 Rev 4 (08/04/09)
Page 17
If ignition of the burner does not occur on the first trial, the
bottom indicator light will flash amber. If the burner(s) do
not light within four trials for ignition, the control will display
a flashing warning, “IGNITION ERROR.” The flashing amber
light will turn to solid red and an audible alarm will sound. If
this occurs, turn the main power switch off, wait 5 minutes,
and then repeat steps 2 and 3.
To Cook in Two-Sided Mode:
1. To start a cook cycle select a product recipe by using the
product keys (1 through 9) or by using the UP/DOWN
keys or to select a product recipe.
The display alternately blinks the recipe and the word
SELECTED 2 times then the recipe displays continuously.
2. The controller regulates the platen and grill temperatures
to the set temperatures of the product selected and
reads “TOO COOL” or “TOO HOT” with “MENU ITEM”, until
the grill attains the set temperature range for the item.
NOTE: If the display reads either “TOO COOL” or “TOO HOT”
the upper platen will not lower and initiate a cooking
sequence.
3 After loading the product onto the grill, press the green
CANCEL/RAISE PLATEN BUTTON and BLACK button
simultaneously. A cook cycle starts and the upper platen
lowers if the product selected is clamshell recipe.
4 To cancel a cook cycle at anytime press the green
CANCEL/RAISE PLATEN BUTTON and the upper platen
will rise if the product recipe selected is clamshell recipe.
5. During a cook cycle, the display shows the product recipe
name in the first line and the remaining cook time count
down in the second line.
6 When the cook timer reaches one, (1), second remaining
a pre-time-out alarm sounds alerting the operator.
7 When the cooking time has been completed the platen
raises automatically. On the controller the “PRODUCT
NAME” and the word “REMOVE” will be displayed and an
audible alert will sound.
8. Pressing the green CANCEL/RAISE PLATEN BUTTON stops
the audible alert and the unit will revert back to IDLE
mode.
To Cook in Flat Grill Mode:
1. To start a cook cycle select a product recipe by using the
product keys (1 through 9) or by using the UP/DOWN
keys or to select a product recipe.
OPERATION
continued
The display alternately blinks the recipe and the word
SELECTED 2 times then the recipe will be displayed
continuously.
2. The controller regulates the grill temperature to the set
temperature of the product selected and reads “TOO
COOL” or “TOO HOT” with “MENU ITEM”, until the grill
attains the set temperature range for the item.
NOTE: If the display reads either “TOO COOL” or “TOO HOT” it
will not initiate a cooking sequence.
3 After loading the product onto the grill, press the green
CANCEL/RAISE PLATEN BUTTON and BLACK button
simultaneously. That will start a cook cycle if the product
selected is clamshell recipe.
4 To cancel a cook cycle at anytime the press the green
CANCEL/RAISE PLATEN BUTTON .
5. During a cook cycle, the display shows the product recipe
name in the first line and the remaining cook time count
down in the second line.
6. The display shows the “SEAR” or “FLIP” alarm message
with flashing in the second line if the current cooking
product is flat recipe and the sear time or flip time is not
zero.
7. A cook alarm sounds with a repeating beep pattern.
Pressing the black RAISE button acknowledges the “SEAR”
or “FLIP” alarm message if the alarm field in system setup
is set to MANUAL.
8. The “SEAR” or “FLIP” alarm message stops after 5 seconds
if the alarm field in system setup is set to AUTO.
9. When a cook is complete, the display shows the product
recipe name in the first line and a flashing “REMOVE”
message in the second line. A repeating beeping alarm
also sounds.
10. Pressing the black RAISE button cancels the cook done
alarm.
11. The unit revertes back to IDLE mode.
Enter Standby Mode:
Stand by mode is used during slow periods to conserve
energy with out a complete shut down of the unit. When
cooking temperatures are again required, pre-heat cook
temperature/time is reduced. Stand by mode temperatures
can be adjusted, see the PROGRAMING section.
1. Select Standby Mode by pressing or until
“STANDBY” is displayed.