Ghp ™ 10 marine autopilot system installation instructions to obtain the best possible performance and to avoid damage to your boat, install the garmin ® ghp 10 marine autopilot system according to the following instructions. Professional installation of the autopilot system is highly recommended. S...
Ghp 10 marine autopilot system installation instructions ghp 10 package contents and tools needed the ghp 10 autopilot system consists of multiple components. Familiarize yourself with all of the components before beginning installation. You must know how the components operate together in order to ...
Ghp 10 marine autopilot system installation instructions the shadow drive the shadow drive is a sensor you install in the hydraulic steering lines of your boat. While the ghp 10 is engaged, the shadow drive temporarily disengages the autopilot when you manually take control of the helm. When you est...
Ghp 10 marine autopilot system installation instructions nmea 2000 cables and connectors the nmea 2000 cables connect the ccu and the ghc 10 to the nmea 2000 network. Use the nmea 2000 power cable and two terminators to create a nmea 2000 network on your boat if one does not exist. For more informat...
Ghp 10 marine autopilot system installation instructions installation preparation before installing the ghp 10 autopilot system, it is important for you to completely understand where all the components will be located on your boat. Temporarily place all the components where you plan to install them...
Ghp 10 marine autopilot system installation instructions encoder ccu power } pump ghp 10 general wiring outline nmea 000 network (see page 0 ) ccu ecu pump (compact .1 l pictured) ghc 10 shadow drive alarm buzzer boat tachometer yellow ccu signal wire (see page 9 ) for ccu bare-wire connections, see...
7 ghp 10 marine autopilot system installation instructions single-helm layout guidelines nmea 000 network ccu ecu pump (1. L pictured) ghc 10 1 vdc* note: this diagram is for planning purposes only. Specific wiring diagrams are included in the detailed installation instructions for each component. H...
Ghp 10 marine autopilot system installation instructions dual-helm layout guidelines nmea 000 network ccu ecu pump (1. L pictured) ghc 10 1 vdc* ghc 10 note: this diagram is for planning purposes only. Specific wiring diagrams are included in the detailed installation instructions for each component...
9 ghp 10 marine autopilot system installation instructions hydraulic considerations – 2.0 l and 1.2 l pumps different boats have different hydraulic considerations you must examine before mounting the pump or disconnecting any hoses. Before starting the hydraulic installation, verify the type of hyd...
10 ghp 10 marine autopilot system installation instructions 2.0 l or 1.2 l pump hydraulic layout on dual-helm boats balanced cylinder port fitting starboard fitting .0 l/1. L pump (and motor) port line return line starboard line shadow drive upper helm p r s p r s lower helm notes: 2.0 l/1.2 l pump ...
11 ghp 10 marine autopilot system installation instructions 2.0 l or 1.2 l pump hydraulic layout on seastar power assist-enabled boats notes: power assist module: it may be necessary to remove the power assist module to gain access to the fittings, the hoses, and the bleed- tee fitting. Remove the b...
1 ghp 10 marine autopilot system installation instructions hydraulic considerations - compact 2.1 l pump different boats have different hydraulic considerations you must examine before mounting the pump or disconnecting any hoses. Before starting the hydraulic installation, verify the type of hydrau...
1 ghp 10 marine autopilot system installation instructions compact 2.1 l pump hydraulic layout on dual-helm boats s balanced cylinder port fitting starboard fitting compact .1 l pump (and motor) port line return line starboard line shadow drive upper helm p r p r s lower helm port line return line s...
1 ghp 10 marine autopilot system installation instructions compact 2.1 l pump hydraulic layout on seastar power assist-enabled boats notes: power assist module: it may be necessary to remove the power assist module to gain access to the fittings, the hoses, and the bleed-tee fitting you may need to ...
1 ghp 10 marine autopilot system installation instructions alternative compact 2.1 l pump hydraulic configurations depending on the hydraulic layout of your boat, alternative hydraulic installations using the compact 2.1l pump are possible: the c1 and h1 ports are directly connected to each other in...
1 ghp 10 marine autopilot system installation instructions hydraulic considerations – legacy 2.1 l pump different boats have different hydraulic considerations you must examine before mounting the pump or disconnecting any hoses. Before starting the hydraulic installation, verify the type of hydraul...
17 ghp 10 marine autopilot system installation instructions legacy 2.1 l pump hydraulic layout on dual-helm boats balanced cylinder port fitting starboard fitting legacy .1 l pump (and motor) port line return line starboard line shadow drive upper helm p r s p r s lower helm notes: legacy 2.1 l pump...
1 ghp 10 marine autopilot system installation instructions seastar power assist-enabled boats balanced cylinder port fitting starboard fitting .1 l pump (and motor) port line return line starboard line shadow drive helm s r p sea star power assist module h1 h c c1 return line notes: power assist mod...
19 ghp 10 marine autopilot system installation instructions installation procedures after you have completely planned the ghp 10 installation on your boat, and have satisfied all the hydraulic, mounting, and wiring considerations for your particular installation, you can begin mounting and connectin...
0 ghp 10 marine autopilot system installation instructions pump/motor body upper fittings lower fittings pump manifold to connect the pump to the hydraulic lines: 1. Consult the hydraulic layout diagrams starting on page 9 to find the correct place to connect the pump to your hydraulic system. 2. Pr...
1 ghp 10 marine autopilot system installation instructions when the shutoff valve is engaged, the boat will steer normally, and the pump will not control the steering system. When the shutoff valve is engaged, you can remove the pump from the system for repair without disconnecting any hydraulic lin...
Ghp 10 marine autopilot system installation instructions connecting the legacy 2.1 l pump to the hydraulic lines the legacy 2.1 l pump must be isolated from the electrical ground of the boat. Use insulating washers under the pump if it is installed on an electrically-grounded (metal) surface. Instal...
Ghp 10 marine autopilot system installation instructions connecting the pump to the ecu do not connect the pump to the ecu until you have mounted the ecu to the boat following the procedures on page 25 . Connecting the compact 2.1 l pump to the hydraulic lines before disconnecting any hydraulic line...
Ghp 10 marine autopilot system installation instructions 4. Disconnect the hydraulic lines from the steering system where appropriate. 5. Use the diagram above to identify the connectors on the pump. 6. Remove the plugs from the five connections on the pump labeled c1, c2, h1, h2, and tank. 7. Route...
Ghp 10 marine autopilot system installation instructions installing the electronic control unit (ecu) to install the ecu, mount it to your boat, connect it to the pump and to the ccu, and wire it to the boat battery. Installing the ecu on a 24 vdc system the ecu hardware has been updated to function...
Ghp 10 marine autopilot system installation instructions if possible, mount the ccu within 16 ft. (5 m) of the ecu. If you cannot mount the ccu within 16 ft. (5 m) of the ecu, extension and replacement cables are available (see page 4 ). To mount the ccu bracket: 1. Determine the best location for t...
7 ghp 10 marine autopilot system installation instructions wiring the shadow drive wire the shadow drive to the ccu/ecu interconnect cable. To wire the shadow drive: 1. Route the bare-wire end of the ccu/ecu interconnect cable to the shadow drive. If the cable is not long enough, extend the appropri...
Ghp 10 marine autopilot system installation instructions wiring the alarm buzzer wire the alarm buzzer to the ccu/ecu interconnect cable. To wire the alarm buzzer: 1. Route the alarm-buzzer cable to the bare-wire end of the ccu/ecu interconnect cable. If the cable is not long enough, extend the appr...
9 ghp 10 marine autopilot system installation instructions 7. Drill the four 1 / 8 in. (3.2 mm) pilot holes. Notice if you are mounting the ghc 10 in fiberglass, it is recommended to use a countersink bit to drill a clearance counterbore through only the top gel-coat layer. This will help to avoid a...
0 ghp 10 marine autopilot system installation instructions connecting the ghc 10 to a nmea 2000 network connect the ghc 10 to the ccu through your existing nmea 2000 network. If you do not have an existing nmea 2000 network on your boat, all the parts needed to build one are supplied in the ghp 10 p...
1 ghp 10 marine autopilot system installation instructions 4. Route the included drop cable to the bottom of the t-connector you added to your nmea 2000 network. If the included drop cable is not long enough, you can use a drop cable up to 20 ft. (6 m) long (not included). 5. Connect the drop cable ...
Ghp 10 marine autopilot system installation instructions notes: to add additional sensors to your nmea 2000 network, follow the instructions included with the sensor. The ghc 10 must connect to the ccu with the yellow ccu signal wire in the ghc 10 data cable. The black wire must connect to ccu groun...
Ghp 10 marine autopilot system installation instructions if your nmea 0183-compatible device has only one receiving wire (rx), connect it to the blue wire (tx/a) from the ghc 10, and leave the white wire (tx/b) from the ghc 10 unconnected. Wiring the ghc 10 to a nmea 0183 device with one receiving w...
Ghp 10 marine autopilot system installation instructions 2. Connect the black wire (-) to the negative (-) side of the battery first. 3. Connect the red wire (+) to the positive (+) side of the battery next. 4. Connect the ecu power cable to the ecu last. To connect the data cable to the ghc 10, ali...
Ghp 10 marine autopilot system installation instructions configuring the ghp 10 the ghp 10 must be configured and tuned to your boat dynamics and motor configuration. Use the dockside wizard and the sea trial wizard on the ghc 10 to configure the ghp 10. These wizards will walk you through the neces...
Ghp 10 marine autopilot system installation instructions completing the sea trial wizard: drive to calm, open water and, if the sea trial wizard does not start automatically, select menu > setup > dealer autopilot configuration > wizards > sea trial wizard . The sea trial wizard welcome screen appea...
7 ghp 10 marine autopilot system installation instructions evaluating the results of the autopilot configuration when the dockside and sea trial wizards are complete, test the autopilot to be sure it is configured correctly. Test the autopilot first at slow speeds (below planing), and then test the ...
Ghp 10 marine autopilot system installation instructions advanced configuration power-on procedure advanced configuration options are not available on the ghc 10 under normal conditions. To access the advanced configuration settings of the ghp 10, use the advanced configuration power-on procedure. T...
9 ghp 10 marine autopilot system installation instructions category setting description tachometer setup verify tachometer with the engine (or engines) running, compare the rpm readings on the ghc 10 with the tachometer on the dashboard of your boat. Adjust the pulses per rev with the arrows if the ...
0 ghp 10 marine autopilot system installation instructions appendix specifications ecu physical dimensions (w×h×d): 6 19 / 32 × 4 19 / 32 × 2 in. (167.6 × 116.8 × 50.8 mm) weight: 1.5 lb. (0.68 kg) temperature range: from 5°f to 131°f (from -15°c to 55°c) case material: fully gasketed, high-impact a...
1 ghp 10 marine autopilot system installation instructions legacy 2.1l pump physical dimensions (w×h×d): 15 × 7 1 / 2 × 7 3 / 16 in. (381 ×190.5 × 182.9 mm) weight: 17.6 lb. (8 kg) temperature range: from 5°f to 131°f (from -15°c to 55°c) cable length: 19 in. (0.5 m) power main power usage: varies b...
Ghp 10 marine autopilot system installation instructions nmea 2000 pgn information ghc 10 receive transmit 059392 iso acknowledgment 059392 iso acknowledgment 059904 iso request 059904 iso request 060928 iso address claim 060928 iso address claim 126208 nmea - command/request/acknowledge group funct...
Ghp 10 marine autopilot system installation instructions mounting templates use the following mounting templates to assist with the mounting process. Ecu mounting template ccu mounting template up (when mounting on a vertical surface).
Ghp 10 marine autopilot system installation instructions.
Ghp 10 marine autopilot system installation instructions 1.2 l/2.0 l pump mounting template.
Ghp 10 marine autopilot system installation instructions compact 2.1 l pump mounting template note: this template should also be used with the legacy 2.1 l pump. Manifold.
7 ghp 10 marine autopilot system installation instructions ghp 10 installation checklist detach this checklist from the installation instructions and use it to assist with the ghc 10 installation process. Read all installation instructions before installing the ghc 10. Contact garmin product support...
© 2010 garmin ltd. Or its subsidiaries all rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of garmin. Garmin hereby...