Garmin GPS 165 Installation Manual - page 11
Av. Kit Install. Manual
190-00066-02 Rev. J
Page 11
SECTION 3 INSTALLATION PROCEDURE
3.1
INSTALLATION ACCESSORIES
The following installation accessories are available.
ANTENNA OPTIONS
010-10040-01
GA 56 LOW PROFILE ANTENNA KIT, W/O CABLE
Includes:
011-00134-00 LOW PROFILE ANTENNA SUBASSEMBLY
1
115-00031-00 BACKING PLATE
1
210-10004-09 NUT, SELF-LOCKING, #8-32
4
253-00002-00 ANTENNA GASKET
1
010-10040-02
GA 56 FLANGE MOUNT ANTENNA
Includes:
011-00147-00 FLANGE MOUNT LOW PROFILE ANTENNA SUBASSEMBLY
1
115-00080-00 NUT PLATE
1
211-62212-14 SCREW, #10-32 X 5/8
4
253-00011-00 ANTENNA GASKET
1
320-00003-00 15 FT LOW-LOSS AVIATION EXTENSION CABLE WITH RIGHT ANGLE BNC CONNECTOR
320-00003-02 30 FT LOW-LOSS AVIATION EXTENSION CABLE WITH RIGHT ANGLE BNC CONNECTOR
330-00087-00 CONNECTOR, BNC, MALE, CLAMP
Note: One cable assembly and one BNC connector are required to make the antenna cable, or it can be fabricated
by the installer from materials meeting the requirements of paragraph 2.3.
011-00313-00
CONNECTOR (J1 and J2) KIT
DATABASE OPTIONS
010-10051-00
MEMORY CARD - WORLDWIDE DATABASE
010-10051-01
MEMORY CARD - AMERICAS DATABASE
010-10051-02
MEMORY CARD - INTERNATIONAL DATABASE
010-10032-03
MEMORY CARD - USER
ANNUNCIATOR OPTIONS
GPN
MID-CONTINENT P/N
DESCRIPTION
013-00029-00
MD41-428
INTEGRATED SW/ANN UNIT, HOR, 28V
013-00029-01
MD41-424
INTEGRATED SW/ANN UNIT, HOR, 14V
013-00029-02
MD41-428 (5V)
INTEGRATED SW/ANN UNIT, HOR, 28V (5V LIGHTING)
013-00029-05
MD41-438
INTEGRATED SW/ANN UNIT, VERT, 28V
013-00029-06
MD41-434
INTEGRATED SW/ANN UNIT, VERT,14V
013-00029-07
MD41-438 (5V)
INTEGRATED SW/ANN UNIT, VERT, 28V (5V LIGHTING)
MISC OPTIONS
190-00066-00
GPS 165 PILOT'S GUIDE
190-00066-01
GPS 165 QUICK REFERENCE GUIDE
190-00066-05
REMOTE BATTERY PACK INSTALLATION INSTRUCTIONS
010-10041-00
REMOTE BATTERY PACK (CONSISTS OF 011-00143-00)
330-00067-00
GPS 1.57542 GHZ NOTCH FILTER
362-00010-00
WALL CHARGER - 110/220VAC
Note: See Figure 3-1 for assistance in pre-planning the installation of the remote battery pack. See 190-00066-
05 for complete and current installation instructions. The remote battery pack is required for A1
Certification.
011-00313-00
Connector, (J1 and J2) Kit
3.2
ANTENNA INSTALLATION
The Low Profile Antenna outline and footprint dimensio!ns are shown in Figures 3-2
and 3-3.
A. Using the backing plate as a template, mark the location of the mounting holes and
the through hole for coax cable. Drill or punch the holes.
B. The antenna installation must provide adequate support for the antenna considering
a maximum drag load of 5 lbs. for the low profile antenna (at subsonic speed).
Install a doubler plate to reinforce thin skinned aircraft. Observe guidelines for
acceptable installation practices as outlined in AC 43.13-2A.