Garmin GPS 19x NMEA 0183 Installation Instructions Manual - page 2
1
Useapenciltomarkthethreescrewlocations
andtotracethecable-holeinthecenterofthe
bracket.
2
Setthesurface-mountbracketaside.
Donotdrillthroughthesurface-mountbracket.
3
Drillthethree
1
/
8
in.(3.2mm)pilotholes.
NotE:IfyouaremountingtheGPS19x
onfiberglass,itisrecommendedtousea
countersinkbittodrillaclearancecounterbore
throughthetopgelcoatlayer(butnodeeper).
Thiswillhelptoavoidcrackinginthegelcoat
layerwhenthescrewsaretightened.
4
Usea1in.(25mm)holesawtocutthecable
holeinthecenter.
5
Placethesealpad
➋
onthebottomofthe
surface-mountbracket,aligningthescrewholes.
6
UsetheincludedM4screwstoattachthe
surface-mountbrackettothemountingsurface.
7
Routethecable
➌
throughthe1in.(25mm)
holeandconnectittotheantenna.
8
Verifythatthelargegasket
➍
isinplaceonthe
bottomoftheantenna,placetheantennaonthe
surface-mountbracket,andtwistitclockwiseto
lockitinplace.
9
Securetheantennatothemountingbracketwith
theincludedM3setscrew
➎
.
10
Routethecableawayfromsourcesofelectronic
interference,andconnectittopowerandto
aNMEA0183-compliantdevice.
Mounting the Antenna on a Pole
Withtheincludedpole-mountadapterattachedtothe
antenna,youcaninstallitonastandard1in.OD,14
threadsperinch,pipe-threadedpole(notincluded).
Youcanroutethecableoutsideofthepoleor
throughthepole.
Beforeyoupermanentlymounttheantenna,testthe
mountinglocationforcorrectoperation.
Mounting the Antenna with the Cable
Routed outside of the Pole
1
Routethecablethroughthepole-mountadapter
➊
,andplacethecableintheverticalslot
➋
alongthebaseofthepole-mountadapter.
➊
➋
➌
2
Screwthepole-mountadapterontoastandard
1in.OD,14threadsperin.,pipe-threadedpole
(notincluded).
Donotovertightentheadapteronthepole.
3
Connectthecabletotheantenna.
4
Placetheantennaonthepole-mountadapter
andtwistitclockwisetolockitinplace.
5
Securetheantennatotheadapterwiththe
includedM3setscrew
➌
.
6
Withtheantennainstalledonthepolemount,fill
theremaininggapintheverticalcableslotwitha
marinesealant(optional).
7
Attachthepoletotheboatifitisnotalready
attached.
8
Routethecableawayfromsourcesofelectronic
interference,andconnectittopowerandto
aNMEA0183-compliantdevice.
Mounting the Antenna with the Cable
Routed through the Pole
1
Positionastandard1in.OD,14threadsperin.,
pipe-threadedpole(notincluded)intheselected
location,andmarktheapproximatecenterofthe
pole.
2
Drillaholeusinga
3
/
4
in.(19mm)drillbitforthe
cabletopassthrough.
3
Fastenthepoletotheboat.
4
Threadthepole-mountadapterontothepole.
Donotovertightentheadapter.
5
Routethecablethroughthepoleandconnectit
totheantenna.
6
Placetheantennaonthepole-mountadapter
andtwistitclockwisetolockitinplace.
7
Securetheantennatotheadapterwiththe
includedM3setscrew
➊
.
➊
➋
8
Withtheantennainstalledonthepolemount,fill
theverticalcableslot
➋
withamarinesealant
(optional).
9
Routethecableawayfromsourcesofelectronic
interference,andconnectittopowerandto
aNMEA0183-compliantdevice.
Mounting the Antenna under a
Surface
Notice
Beforeattachingtheunder-deckmountingbracketto
thesurface,verifythatthesuppliedscrewswillnot
penetratethesurface.Ifthesuppliedscrewsaretoo
long,youmustpurchasesurface-appropriatescrews
tocompletetheinstallation.
Becausetheantennacannotacquiresignalsthrough
metal,itmustbemountedunderafiberglasssurface
only.
1
Determineandtestthelocationundera
fiberglasssurfacewhereyouwanttomount
theantenna.
➋
➌
➊
2
Placetheadhesivepads
➊
ontheunder-deck
mountingbracket
➋
.
3
Placetheantennaintheunder-deckmounting
bracket.
4
Adheretheunder-deckmountingbrackettothe
mountingsurface.