Questions? Refer to www.Goldlinecontrols.Com for latest manual revisions, additional information and helpful service. Or, you may visit your local authorized aqua rite dealer or call 888-921- pool (7665) for assistance. Electrolytic chlorine generator basic pool maintenance requirements 888-921-pool...
Important safety instructions when using this electrical equipment, basic safety precautions should always be followed, including the following: • read and follow all instructions 16 • use copper conductors only • disconnect all ac power during installation. • warning - to reduce the risk of injury,...
Table of contents operation operation operation operation operation general general general general general.........................................................................................1 water chemistry water chemistry water chemistry water chemistry water chemistry..........................
14 1 operation the aqua rite ® is an automatic chlorine generation system for pool or spa sanitation. The operation requires a low concentration of salt (sodium chloride) in the pool water. These levels are low enough that it normally will not be tasted. The aqua rite automatically sanitizes your po...
Saturation index the saturation index (si) relates to the calcium and alkalinity in the water and is an indicator of the pool water "balance". Your water is properly balanced if the si is 0 ±.2. If the si is below -0.2, the water is corrosive and plaster pool walls will be dissolved into the water. ...
3 salt level use the chart on page 4 to determine how much salt in pounds or (kgs) need to be added to reach the recommended levels. Use the equations below (measurements are in feet/gallons and meters/liters) if pool size is unknown. The ideal salt level is between 2700-3400 ppm (parts per million)...
4 11 flow switch connector bonding lug to pool bonding system cutout for cell cable wiring power must be shut off at the circuit breaker before performing any wiring. Be sure to follow local and nec electrical codes. To provide safe operation, the aqua rite ® must be properly grounded and bonded. In...
5 plumbing ensure that the aqua rite ® installation does not constitute a cross connection with the local potable water supply. Consult local plumbing codes. The flow switch and cell should be plumbed in the return line to the pool/spa. The preferred installation is after (downstream) all the pool e...
6 controls main switch auto : for normal operation, the main switch should be left in the auto posi- tion. In this position the aqua rite will produce chlorine according to the "de- sired output %" adjustment setting for the entire filtering/pumping cycle. Super chlorinate : when you have an abnorma...
7 8 "desired output %" adjustment knob the "desired output %" adjustment knob is located in the lower center of the aqua rite control panel. This setting is used to control the amount of chlorine the aqua rite generates. Raise this setting to increase chlorine level and lower it to decrease chlorine...
7 8 "desired output %" adjustment knob the "desired output %" adjustment knob is located in the lower center of the aqua rite control panel. This setting is used to control the amount of chlorine the aqua rite generates. Raise this setting to increase chlorine level and lower it to decrease chlorine...
6 controls main switch auto : for normal operation, the main switch should be left in the auto posi- tion. In this position the aqua rite will produce chlorine according to the "de- sired output %" adjustment setting for the entire filtering/pumping cycle. Super chlorinate : when you have an abnorma...
5 plumbing ensure that the aqua rite ® installation does not constitute a cross connection with the local potable water supply. Consult local plumbing codes. The flow switch and cell should be plumbed in the return line to the pool/spa. The preferred installation is after (downstream) all the pool e...
4 11 flow switch connector bonding lug to pool bonding system cutout for cell cable wiring power must be shut off at the circuit breaker before performing any wiring. Be sure to follow local and nec electrical codes. To provide safe operation, the aqua rite ® must be properly grounded and bonded. In...
3 salt level use the chart on page 4 to determine how much salt in pounds or (kgs) need to be added to reach the recommended levels. Use the equations below (measurements are in feet/gallons and meters/liters) if pool size is unknown. The ideal salt level is between 2700-3400 ppm (parts per million)...
Saturation index the saturation index (si) relates to the calcium and alkalinity in the water and is an indicator of the pool water "balance". Your water is properly balanced if the si is 0 ±.2. If the si is below -0.2, the water is corrosive and plaster pool walls will be dissolved into the water. ...
14 1 operation the aqua rite ® is an automatic chlorine generation system for pool or spa sanitation. The operation requires a low concentration of salt (sodium chloride) in the pool water. These levels are low enough that it normally will not be tasted. The aqua rite automatically sanitizes your po...
Table of contents operation operation operation operation operation general general general general general.........................................................................................1 water chemistry water chemistry water chemistry water chemistry water chemistry..........................
Important safety instructions when using this electrical equipment, basic safety precautions should always be followed, including the following: • read and follow all instructions 16 • use copper conductors only • disconnect all ac power during installation. • warning - to reduce the risk of injury,...
Questions? Refer to www.Goldlinecontrols.Com for latest manual revisions, additional information and helpful service. Or, you may visit your local authorized aqua rite dealer or call 888-921- pool (7665) for assistance. Electrolytic chlorine generator basic pool maintenance requirements 888-921-pool...