1. DL manuals
  2. Goldstein
  3. Fryer
  4. FRE-18D
  5. User Manual

Goldstein FRE-18D User Manual

Manual is about: ELECTRIC FRYERS

Summary of FRE-18D

  • Page 1

    Electric fryers proudly australian made installation procedure – user manual service instruction models fre-18d, fre-24d, fret-18d fre-24d fre-18d fret-18d established 1911 the cooking equipment professionals www.Goldsteineswood.Com.Au.

  • Page 2: Table of Contents

    Table of contents 1. Introduction page 3 2. Installation page 4 & 5 3. Commissioning page 6 4. Operating instructions page 7 & 8 5. Draining & filtering instructions page 9 & 10 6. Technical data page 11 & 12 7. Resistance vs temperature page 13 8. Servicing page 14 & 15 9. Trouble shooting page 16 ...

  • Page 3

    1 . Introduction congratulations for purchasing your goldstein commercial cooking appliance. J. Goldstein & co. Is a wholly owned australian company and has been operating since 1911, building high quality products. The information in this manual will assist your installer and ensure correct locatio...

  • Page 4

    2. Installation receiving inspection – pre-installation please follow these instructions carefully • remove baskets and cartons from unit, check contents. • lift off base and screw the adjustable legs into the base. • set units in correct position. • adjust feet till they are all touching the floor ...

  • Page 5: Caution

    2. Installation cont’d please follow these instructions carefully 1. Set unit in desired position. If rear wall is of combustible material ensure there is a minimum distance of 100mm between the back of the unit and the wall. 2. Adjust feet till they are all touching the floor and using a spirit lev...

  • Page 6: Commissioning Check List

    3. Commissioning commissioning appliance – details, testing, checking pressure etc. Commissioning check list 1. Check for damage and missing ports. 2. Remove all plastic coating from s/steel panels. 3. Make sure all parts are in their correct position e.G. Trays elements. 4. Make sure all electric c...

  • Page 7

    4. Operating instructions 1 operating before first use clean protective oil from bright parts and interior of pan with a solution of washing soda or other grease dissolving material. Drain through valve in bottom then rinse thoroughly. (note: it must be completely rinsed out for even a small particl...

  • Page 8

    4. Operating instructions cont’d weekly a) completely drain the fryer vessel into either the filter or steel container. Do not use a plastic bucket or glass container. B) clean the vessel with a good grade of cleaner or hot water and a strong detergent. D) bring to a rolling boil, turn the heat down...

  • Page 9

    5. Draining & filtering instruction a. Draining warning draining and filtering of shortening must be accomplished with care to avoid the possibility of a serious burn caused from careless handling. Warning the element must not be turned on when the fry pot is empty. A few minutes of element operatio...

  • Page 10

    5. Draining & filtering instructions cont’d b. Boiling out the frypots clean new fry pots as follows before filling with shortening: 1. Before operating the element, close fryer drain valve and fill empty fry pot with a mixture of cold water and boil-out washing soda solution. Fill to the fry pot oi...

  • Page 11

    6. Technical data fre-18d-24d fret-18d digital control srt 701 caho im013b2/p11.

  • Page 12

    6. Technical data cont’d srt-701 caho features 1. Terminal design: adopts a special design with strong stress, provide good connection. Its also suitably for vibrating 2. Pcbs: whole series use double sided pcbs, quality can be assured. 3. Pcb’s location: be fixed by vertical type which will not be ...

  • Page 13

    7. Resistance vs temperature rtd sensors - table for platinum resistance elements. R(0) = 100 ohm. Alpha-0.00385. Resistance values in ohms from 0 °c to + 150°c. Pt100 ohm rtd to din 43760 - iec 751 °c 0 1 2 3 4 5 6 7 8 9 0 100.00 100.39 100.78 101.17 101.54 101.95 102.34 102.73 103.12 103.51 10 103...

  • Page 14

    8 servicing accessing fryers for servicing warning moving a fryer filled with hot shortening may cause splattering of the hot shortening. Extreme care must be exercised. Filling fill pan to level indicated on back of pan. The fre-18 size fryer takes approximately 27 litres of oil. The fre-18t takes ...

  • Page 15

    8. Servicing cont’d accessing fryers for servicing warning moving a fryer filled with hot shortening may cause splattering of the hot shortening. Extreme care must be exercised. 1. Switch off main power – electrical lead and remove plug if fitted. 2. Remove restraining devices typically applied to t...

  • Page 16

    9. Trouble shooting trouble shooting. These troubleshooting procedures must be carried out only by a goldstein authorised maintenance & repair centre or company specialising in restaurant cooking appliances. The problems and possible solutions given below cover those most commonly encountered. Facto...

  • Page 17

    10. Wiring diagram – fet18 digital control fet18 digital control n a2 a1 nc micro switch cno main switch main switch contactor n b contactor n a probe tc 3 220 110 n 2 1 17 16 15 element 7.0kw n tc n b a contactor contactor n 220 110 2 3 n 1 probe 16 17 15 over temp. Over temp. Element 7.0kw n other...

  • Page 18

    10a. Wiring diagram – fre-18d – 24d no cn c mi cr o sw it ch a ter m in a l bl oc k b co nt acto r temperature co nt ro ller sr-t 701 p r o be (p t -10 0) e l ements 7.0kw x 3 co nt acto r b a overtem p e r at ur e thermost at wi n g im013b2/p18.

  • Page 19

    11. Drawings fre-18d & 24d model: fre-18/d, fre-24/d 15 14 29 10 12 11 6 18 1 17 26 2 9 3 22 23 31 19 20 30 32 27 16 24 28 7 25 8 13 4 5 9 21 26 7a 27 m013b2/p19.

  • Page 20

    11. Spare parts fre-18d & 24d item no. Code description 1. Mbkfe180 basket – fre18 2. Fre18m02 scrap arrester – 355 x 355 2. Fre24m02 scrap arrester – fre24 3. Frg18p27 basket holder 3. Frg24p27 basket holder 4. Mth00238 control – elec. Overtemp. (238°c) 5. Eswm0006 micro switch 6. Eevm7501 element ...

  • Page 21

    12. Drawing model: fret-18d im013b2/p21 29 13 13 1 3 23 18 22 2 6 21 9 16 26 17 24 28 7 8 5 4 4 24 20 19 11 12 10 14 15 30 31 27.

  • Page 22

    12. Spare parts model: fret-18d item no. Code description 1. Mbkfe180 basket – fre18 2. Fet18m01 scrap arrester 3. Frg18p27 basket holder 4. Mth00238 control – ele overtemp. (238°c) 5. Eswm0006 micro switch 6. Eevm7501 element – 7kw fre18 / fre24 7. Etc00893 control – digital 893 fryer fre-d 8. Esw0...

  • Page 23

    13. Warranty installation must be carried out according to local regulations by qualified trade persons. Isolating switch(es), shut-off valves etc must be within easy reach of the machine for future service and maintenance requirements. If in doubt call goldstein/eswood or their representative for f...

  • Page 24

    14. J goldstein & co pty ltd branches for inquiries please call your nearest state branch: head office 211-213 woodpark road new south wales 2564 phone: 02 9604 7333 fax: 02 9604 5420 victoria queensland unit 13 unit 3 260-264 wickham road 49 logan road moorabbin woolloongabba victoria 3189 queensla...