Golmar 295 Series Instruction Manual

Other manuals for 295 Series: Instruction Manual, Instruction manual

Summary of 295 Series

  • Page 1

    T3403en rev.0204 stadio plus instructions manual audio and video door entry system digital installation with coded panel golmar se reserva el derecho a cualquier modificación sin previo aviso. Golmar se réserve le droit de toute modification sans préavis. Golmar reserves the right to make any modifi...

  • Page 2

    1 introduction introduction..........................................1 index ...................................................1 system characteristics ............................2 starting recommendations......................2 system operation...................................3 door panel insta...

  • Page 3

    System operation system characteristics updated features from 5.00 version starting recommendations o management of up to 255 internal buildings of 1,000 apartments each. O new programming menu structure. O direct call code that allows to use a different call code from the one recorded on the monito...

  • Page 4

    4 5 door panel installation mbedding box positioning. E 1650 1850 1450 the upper part of the door panel should be placed at 1,65m. Height roughly. The hole dimensions will depend on the number of door panel modules. The door panel has been designed to be placed under most of the environmental condit...

  • Page 5

    6 7 door panel installation door panel installation enabled. Disabled. Coaxial. Twisted pair. Maximum. Minimum. Reset. Standby. Ssembly the sound module. A insert the sound module in the grille module. For a proper assembly, align the light push button and the microphone rubber of the sound module w...

  • Page 6

    The door panel has two memory banks to plug 256kb memory modules in. Each module allows to record the custom text for a maximum of 1000 users. The system is delivered with one memory module placed in the bank number 0 (bk0), where the system configuration will be recorded. Important: in case of door...

  • Page 7

    10 door panel programming 11 door panel programming rogramming menu. P golmar 16:30 access control options can be changed on this menu. Press ok to enter into this menu. Access control this menu allows to fill the repertory and to change its options. Press ok to enter into this menu. Repertory conti...

  • Page 8

    12 door panel programming 13 door panel programming display message golmar display message golmar o.K. :1315 installer pin modify value :1315 o.K. :9876 installer pin o.K. 6 7 8 9 :1111 user pin modify value :1111 o.K. O.K. 2 3 4 5 :5432 user pin onfiguration menu. C onfiguration menu. C yes call to...

  • Page 9

    14 door panel programming 15 door panel programming 1 st access code :2222 o.K. Yes access control * ccess control menu. A o.K. Access control :2222 modify value :4013 1 st access code o.K. 3 1 0 4 2 nd access code 3 rd access code :3333 :4444 :03 door open time modify value :03 o.K. :10 door open t...

  • Page 10

    16 door panel programming 17 door panel programming repertory:new enter address o.K. :000 o.K. 2 0 1 9 0 4 3 0 0 enter direct cod :000000 o.K. _ enter name setting recorded repertory o.K. Epertory menu. R note: to make a call it will not be necessary to enter the zero placed on the left side of the ...

  • Page 11

    18 door panel programming 19 door panel programming important: the repertory content can be only transmitted between two equipments: never place more than one system in both transmission or reception modes. It's possible that, during transmission, other of the installed equipments random operates (c...

  • Page 12

    20 21 door panel programming for fast searching press one of the arrow keys followed by the number of entries to be skipped. For a faster search use arrow keys followed by number 0 (10 in 10 entries) or key symbol (100 in 100 entries). The search is realized of 5 in 5 entries. From that moment, each...

  • Page 13

    23 22 on-off push button. After any monitor reset and during the next 45 seconds, all the monitor functions will be disabled, with the exception of call reception. If the handset is on the craddle allows the activation of an optional second camera (*). If not, allows to make an intercom call or to a...

  • Page 14

    25 24 v in v out malla shield malla shield a hz- int sa cto 2c a1 vp mp d ref rcpl-plus lote code 11758882 colocar la parte superior de la regleta a 1,60m. Del suelo. Place the top part of the monitor connector at 1,60m. From the floor. 50mm. 50mm. Presionar para abrir. Press to open. Terminals +, –...

  • Page 15

    27 26 avoid to place the monitor near to heating sources, in dusty locations or smoky environments. To install the monitor directly over the wall, drill two holes of Ø6mm. And use the supplied screws. The upper part of the monitor connector must be placed at 1,60m. Height roughly. The minimum distan...

  • Page 16

    29 28 telephone description telephone description escription of the t-940 plus telephone. D a. B. C. D. E. F. G. H. I. Telephone handset. Speaker grille. Microphone hole. Subjection hole. Telephone cord connectors. Function push buttons. On-off light indicator. Call reception volume control. Hook sw...

  • Page 17

    31 30 telephones programming switch off the telephone to be programmed. Once the telephone is off, press the door release push button. With the door release push button pressed switch on the telephone. To program the telephone as master, switch it off and on again. To program it as slave, press the ...

  • Page 18

    Fa-plus/c sec pri ~ ~ + + - - sec pri ~ ~ + + - - 32 33 cv+ cv- d malla v in- a in a out v in+ v out- v out+ + cn1 cn2 - cv+ cv- d malla v in- a in a out v in+ v out- v out+ + cn1 cn2 - jp 4 3 2 1 jp 4 3 2 1 a a _ _ + + d d malla malla v in v in v out v out cn4 cn4 a _ + d malla v in v out cn4 a _ +...

  • Page 19

    Sec pri ~ ~ + + - - 34 35 jp1 fa-plus/c sec pri ~ ~ + + - - cv+ cv- d malla v in- a in a out v in+ v out- v out+ + - cv+ cv- d malla v in- a in a out v in+ v out- v out+ + - jp 4 3 2 1 jp 4 3 2 1 cn1 cn2 cn1 cn2 jp2 a a d d ct + + v pi v d1 m pi m d1 _ _ a d ct + v d2 m d2 _ a d + v po m po _ d2l-pl...

  • Page 20

    Sec pri ~ ~ + + - - a a + + _ _ d d t-940 plus t-940 plus a + _ d t-940 plus a + _ d t-940 plus fa-plus/c sec pri ~ ~ + + - - cv+ cv- d malla v in- a in a out v in+ v out- v out+ + - cv+ cv- d malla v in- a in a out v in+ v out- v out+ + - jp 4 3 2 1 jp 4 3 2 1 cn1 cn2 cn1 cn2 1 4 7 2 5 8 3 6 0 9 c ...

  • Page 21

    38 39 installation diagrams fa-plus/c c o n ti n u e o n t h e f o ll o w in g p a g e sec pri ~ ~ main + + - - e s + s1 e s + s1 fa-plus/c sec pri ~ ~ main + + - - slave door panel master door panel cv+ cv- d malla v in- a in a out v in+ v out- v out+ + cn1 cn2 - cv+ cv- d malla v in- a in a out v ...

  • Page 22

    40 41 installation diagrams 1,50mm² 2,50mm² 0,25mm² 0,25mm² rg-59 rg-59 terminal sections chart 100m. Distance 300m. A , a , a, d in out v , v , v , v in+ out+ in out +, –, cv+, cv– e s + s1 s2 sec pri ~ ~ + + - - cv+ cv- d malla v in- a in a out v in+ v out- v out+ + cn1 - sw1 sec pri ~ ~ + + - - c...

  • Page 23

    43 42 sa + t t r r m m sar-90 sa + t t r r m m sar-90 tf-104 sec ~ ~ cv+ cv- - a + _ d int a _ + d a1 malla v in v out cn4 a _ + d a1 malla v in v out cn4 a _ + d int malla v in v out cn4 a _ + d malla v in v out cn4 optional connections optional connections the lock release can be activated at any ...

  • Page 24

    45 44 optional connections troubleshooting hints hz- - sa + t t r r m m sar-90 a _ + d 2c malla v in v out cn4 oor bell push button connection. D the platea plus monitor and the t-940 plus telephone can be used to receive the calls made from the apartment door, saving the use of a bell. Wire the pus...

  • Page 25

    Golmar se reserva el derecho a cualquier modificación sin previo aviso. Golmar se réserve le droit de toute modification sans préavis. Golmar reserves the right to make any modifications without prior notice. Golmar@golmar.Es www.Golmar.Es.