Summary of S1016
Page 1
H3c s1016/1024 ethernet switch user manual hangzhou h3c technologies co., ltd. Http://www.H3c.Com manual version: t2-um-20080418-1.05.
Page 2: Ltd.
Copyright © 2004-2008, hangzhou h3c technologies co., ltd. All rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologies co., ltd. Trademarks h3c, , aolynk, , h 3 care, , top g, , irf, netpilot, neoc...
Page 3: Technical Support
Technical support soho@h3c.Com http://www.H3c.Com.
Page 4: About This Manual
About this manual organization this document is organized as follows: chapter content chapter1 product overview this chapter describes the appearance and features of this product. Chapter2 switch installation this chapter describes the precautions and steps to install this product. Conventions the m...
Page 5
This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed..
Page 6: Table of Contents
User manual h3c s1016/1024 ethernet switch table of contents i table of contents chapter 1 product overview ........................................................1-1 1.1 introduction ........................................................................1-1 1.2 product specifications ...............
Page 7: Chapter 1 Product Overview
User manual h3c s1016/1024 ethernet switch chapter 1 product overview 1-1 chapter 1 product overview 1.1 introduction h3c s1016/1024 ethernet switch is a management-free product at desktop level. It offers wire-speed layer 2 switching immediately after the product is powered on without any configura...
Page 8
User manual h3c s1016/1024 ethernet switch chapter 1 product overview 1-2 item description port attribute rj-45 connector compliant with ieee 802.3 and ieee 802.3u 10/100 mbps transmission rate half duplex, full duplex, and auto-negotiation auto-mdi/mdi-x cable 10base-t: category-3/-4/-5 twisted pai...
Page 9: 1.3 Hardware Description
User manual h3c s1016/1024 ethernet switch chapter 1 product overview 1-3 table 1-2 features of s1016/1024 features description wire-speed layer 2 switching all ports support wire-speed forwarding. All ports are in the same broadcast domain. Switching mode store and forward mac address table address...
Page 10
User manual er 1 product overvie h3c s1016/1024 ethernet switch chapt w 1-4 figure 1-2 front view of s1024 ii. Rear panel the s1016 has an ac power socket and a grounding pole on its rear panel as shown below: figure 1-3 rear view of s1016 the s1024 has an ac power socket and a grounding pole on its...
Page 11: 1.3.2 Leds
User manual h3c s1016/1024 ethernet switch chapter 1 product overview 1-5 1.3.2 leds table 1-3 leds of the s1016/1024 led status indication green the switch is powered on. Power off the switch is powered off. Green the port works in 100 mbps mode. Speed off the port works in 10 mbps mode or no ether...
Page 12: 2.1.1 Security Tips
User manual h3c s1016/1024 ethernet switch chapter 2 switch installation 2-1 chapter 2 switch installation 2.1 installation preparations 2.1.1 security tips to avoid any device impairment or bodily injury caused by improper use, take the precautions listed below: z before cleaning the switch, please...
Page 13
User manual h3c s1016/1024 ethernet switch chapter 2 switch installation 2-2 caution: there is a seal on one mounting screw of the chassis of the s1000 series. It must remain untouched unless the agent is on the spot to maintain your switch. Please contact your local agent and get permission if you ...
Page 14: 2.2 Installing The Switch
User manual h3c s1016/1024 ethernet switch chapter 2 switch installation 2-3 z keep the switch far away from high-power radio launchers, radar launchers, and equipment with high-frequency and high-current. Z use electromagnetic shielding if necessary. For example, you can use shielded port cable. Z ...
Page 15
User manual h3c s1016/1024 ethernet switch chapter 2 switch installation 2-4 step 3: check the status of the power led on the switch. On means the connection is ok. 2.2.3 examining the installation z check if the cables are correctly connected with the s1016/1024. Z check if all port cables travel i...