1. DL manuals
  2. H3C
  3. Switch
  4. S12500 Series
  5. Quick Start Manual

H3C S12500 Series Quick Start Manual

Other manuals for S12500 Series: Installation Manual, Installation Instructions Manual

Summary of S12500 Series

  • Page 1

    H3c s12500 routing switch series quick start guide hangzhou h3c technologies co., ltd. Http://www.H3c.Com document version: 6pw101-20120508.

  • Page 2

    Copyright © 2011-2012, hangzhou h3c technologies co., ltd. And its licensors all rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologies co., ltd. Trademarks h3c, , aolynk, , h 3 care, , top g, , i...

  • Page 3

    I contents quick start guide ·························································································································································· 1 preparing for installation ·······················································································...

  • Page 4

    1 quick start guide note: this quick start guide provides basic instructions for installing an s12500 routing switch. For more detailed installation procedures, see h3c s12500 routing switch series installation guide . Preparing for installation esd prevention to prevent the electronic components fr...

  • Page 5

    2 humidity, cleanness, emi, grounding, power module, and space requirements. For more information, see h3c s12500 routing switch series installation guide: installation tools and accessories installing the switch figure 2 installation flow installing the switch in a rack check before installation be...

  • Page 6

    3 figure 3 installing the slide rails (1) middle of the narrower metal area between holes (2) 1 ru installing cage nuts 1. Align the mounting bracket with the left rack post, making sure that the bottom edge and the slide rail are level. Mark the positions of the cage nuts on the rack post according...

  • Page 7

    4 installing the mounting brackets figure 5 installing the mounting brackets (for the s12504) figure 6 installing the mounting brackets (for the s12508/s12518) mounting the switch in the rack 1. Use several people to place the switch on the slide rails or rack shelf and slide the switch into the rac...

  • Page 8

    5 figure 7 installing the switch in a standard 19-inch rack grounding the switch 1. Remove the two grounding screws from the switch chassis. 2. Use the grounding screws to attach one end of the grounding cable to the chassis. 3. Connect the other end of the grounding cable to the grounding strip of ...

  • Page 9

    6 figure 8 connecting the grounding cable installing the power modules note: h3c recommends that you install at least three power modules to one power frame. Installing a dc power module 1. Rotate the power frame cover up with both hands. 2. Pull the clip at the bottom left corner of the power modul...

  • Page 10

    7 figure 9 installing a power module installing an ac power module to install an ac power module, install a pem first, and then install the ac power module. To install a pem: 1. Loosen the screws on the filler panel of the pem slot with a phillips screwdriver to remove the filler panel. 2. Insert a ...

  • Page 11

    8 figure 10 installing a pem the procedures for installing an ac power module are similar to installing a dc power module. For more information, see “ installing a dc power module .” installing a fan tray note: the s12504 has one fan tray. Each of the s12508 and the s12518 has two fan trays. They ar...

  • Page 12

    9 figure 11 installing a fan tray (for the s12504) figure 12 installing a fan tray (for the s12508/s12518) installing a card slot requirements install mpus, lpus, and switching fabric modules into appropriate slots as shown in figure 13 and figure 14 ..

  • Page 13

    10 note: on an s12504 switch, install at least one mpu, one interface card, and three switching fabric modules. On an s12508 or s12518 switch, install at least one mpu, one interface card, and seven switching fabric modules. Figure 13 slot requirements (for the s12504) (1) mpu slots (with red edges)...

  • Page 14

    11 installing a card this section describes how to install an mpu as an example. To install an mpu: 1. Remove the protective box before installing an mpu: { put on an esd-preventive wrist strap and then loosen the captive screws that fix the mpu to the protective box with a phillips screwdriver. { p...

  • Page 15

    12 figure 17 installing a card (for the s12508/s12518) connecting power cords note: make sure that the power switch is in the off position before you connect the power cords. Connecting a dc power cord warning! A plastic protection cover is installed in front of the grounding strip to protect operat...

  • Page 16

    13 figure 18 connecting the dc power cord to the grounding strip 5. Connect the other end of the dc power cord to the power source: { connect the other end of the black dc power cord to the rtn(+) terminal that provides power to the switch. { connect the other end of the blue dc power cord to the ne...

  • Page 17

    14 connecting an ac power cord caution: typically 10 a busbars are available in the equipment room but the lstm2pemc6 requires a 16 a power cord (ac), so you need to use a 16 a busbar, and make sure that the ac power module system can provide enough power. For ac power cords used in different countr...

  • Page 18

    15 verifying the installation warning! Each of the s12504 and s12508 has one power switch, and an s12518 has two power switches. Make sure that you have turned off the power before checking the installation to avoid bodily injury and switch damage. After the installation is completed, verify the ins...

  • Page 19

    16 figure 21 connecting the console cable powering on the switch verify that the power cord is connected to the power source, power on the switch, and verify that the leds on the switch are normal. Table 2 led description when the switch is operating properly module led status mpu sfc (red/green) fl...

  • Page 20

    17 module led status fan tray run (green) flashing alm (red) off note: for more information about the leds, see h3c s12500 routing switch series installation guide . Obtaining documentation take the following steps to get related documents from the h3c website at www.H3c.Com. 1. Go to http://www.H3c...

  • Page 21

    18 index c e g i p v c connecting power cords, 12 connecting the console cable, 15 e esd prevention, 1 examining the installation site, 1 g grounding the switch, 5 i installation tools and accessories, 2 installing a card, 9 installing a fan tray, 8 installing the power modules, 6 installing the swi...