Hager 2916 Installation Instructions Manual
2916 Keypad
Installation Instructions
I-EA00080
Rev 6, Rev Date: 6/8/2016
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
INSTALLATION INSTRUCTIONS
2916
The 2916 Indoor/Outdoor Keypad Surface Mount is a digital keyless
entry system designed for access control applications. The keypad is
integrated in a heavy cast vandal resistant housing, designed to be
mounted on a rugged, surface mounting plate and may be mounted
in a standard single-gang electrical box. The indoor/outdoor backlit
keys have bright, easy-to-read graphics.
Up to 500 entry codes, from 4 to 6 digits in length, can be
programmed. They can activate either, or both of the relay outputs.
The “anti-passback” feature prevents using the same code again
before the programmed time elapses.
All system indicators are long-lasting, solid state LEDs. Two
indicators show the status of the entry system. The left indicator lights
red to indicate power, then turns green when access is granted. The
right indicator lights yellow when the keypad is in “lockout” condition
(from too many incorrect code entries). The yellow LED flashes when
the keypad is in programming mode. An internal sounder beeps when
each key is pressed. An internal jumper sets the sounder volume
high or low
The SENSE input can be used two ways.
If programmed for “door
sense” the input is wired to a normally closed switch on the door to
detect when the door is opened or closed. Forced entry or door ajar
situations can then be detected. Using door sense,
the “Auto-relock”
feature will prevent “tailgating” by turning off the Main Relay output
immediately when the door is closed after access has been granted.
If the SENSE
input is programmed for “inhibit”, the input can be wired
to a “service” switch or automatic timer that will disable the Main
Relay when required.
The REQUEST-TO-EXIT input can be wired to a pushbutton to
provide codeless activation of Main Relay, Auxiliary Relay, Output #3
or Output #4 (programmable).
The ALARM SHUNT output activates when access is granted. This
output can be wired to shunt alarm contacts on the access door/gate
to prevent triggering of an alarm when authorized access occurs.
The 2916 is powered from a 12-24V AC or DC source. The
EEPROM memory retains all entry codes and programming, even
without power. An internal jumper is provided to reset the master
code. The Main Relay has a 5 Amp capacity. The Auxiliary Relay
has a 2 Amp capacity. Two solid state outputs, capable of switching
100 mA to common, are programmable to signal forced entry, door
ajar, lockout, alarm circuit shunting, request-to-exit, and keypad active
conditions.
Features
·
Keypad programmable
·
500 user codes
·
4 to 6 digit user codes
·
4 independent outputs
·
4 independent timers
·
2 Form C relay contacts
·
2 solid state open collector outputs
·
Program entry codes to activate one or
two relays
·
Disable input
·
Door sense input
·
Request-to-exit/enter input
·
Keypad tamper lockout
·
Timed anti-passback
·
Anti-tailgate
·
Two LED status indicators
·
Tactile key feel
·
Audible code entry verification
·
12 or 24V, AC or DC operation
SPECIFICATIONS
Mechanical
Dimensions: 3.00" W x 5.75" H x 1.375" D
(1.4375
” wall projection)
Electrical
Input Voltage: 12-24 Volts AC or DC
Operating Current: 30 mA typical, 150 mA max
Output Ratings
Main Relay:
Form “C” 5 Amps @ 28 Volts max
Auxiliary Relay:
Form “C” 2 Amp @ 28 Volts max
Type: Solid state outputs (Outputs #3 & #4)
Short-to-common 100 mA @ 24 VDC maximum
Environmental
Temperature: -22°F to 149°F (-30°C to 65°C)
Humidity: 5% to 95% non-condensing
Page 1 of 8