Hager 2916 Installation Instructions Manual - page 2
2916 Keypad
Installation Instructions
I-EA00080
Rev 6, Rev Date: 6/8/2016
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
QuickStart Programming
To enter Programming Mode, enter #9# plus the Master Code. The yellow indicator will blink slowly showing that the 2916 is in
programming mode. Use the option codes to program each function. After the new data entry is complete for each function , the
yellow indicator will flash quickly while the data is being stored and the green indicator will light briefly if the programming has been
accepted. The red indicator will light if any programming data is entered incorrectly or the function is rejected. If a red indicator is
seen, the entire function (option code + data) will have to be fully re-entered.
CAUTION
IF THE UNIT IS AC POWERED, MAKE SURE
THAT THE SECONDARY OF THE SYSTEM IS
ISOLATED FROM EARTH GROUND
!
!
Test your new user code
Enter user code ‘9876#’. The green indicator should illuminate, the main relay
should activate and the door should unlock for 5 seconds.
KEYPAD
POWER
WIRE
HARNESS
(E1-E8)
MAIN
RELAY
AUXILIARY
RELAY
ANTI-TAMPER
SWITCH
BACK
JP1
E1
E8
JP2
RED/GREEN
POWER/ACCESS
INDICATOR
YELLOW
“PROGRAM”
INDICATOR
KEYPAD
FRONT
Deleting a user code
Step 1. Enter: #9# 123456# - Enter the program mode (default master code)
Step 2. Enter: 02# 002# 002# - User 2 has been deleted.
Step 3. Enter: # - Exit programming mode
**
**
Adding additional user codes
Step 1. Enter: #9# 123456# - Enter the program mode (default master code)
Step 2. Enter: 01# 002# 2222# 2222# 1# -
PIN code ‘2222’ is assigned to User #002 to
momentarily activate the main relay
Step 3. Enter: 01# 003# 2580# 2580# 10# -
PIN code ‘2580’ is assigned to User #003 to
toggle (on/off) the main relay
Step 4. Enter: # - Exit programming mode
Program the first user code
Step 1. Enter: #9# 123456# - Enter the program mode (default master code)
Step 2. Enter: 03# 4# - Set the entry code length to 4 digits
Step 3. Enter: 21# 5# - Set the main relay activation time for 5 sec.
Step 4. Enter: 01# 001# 9876# 9876# 1# -
PIN code ‘9876’ is assigned to User #001 to
momentarily activate the main relay
Step 5. Enter: # - Exit programming mode
Once the code length and relay time has been set you do not need to set them again for
additional users.
**
Fig. 2 Wiring Pigtail Color Code
E
1
E
2
E
3
E
4
E
5
E
6
E
7
E
8
SENSE
GROUND
REQUEST TO EXIT
GROUND
GROUND
OUTPUT 3
OUTPUT 4
GROUND
BLACK
PINK/SALMON
BLUE
BLACK
GREEN
VIOLET
BLACK
GRAY
C
N/O
N/C
C
N/O
N/C
N/C DOOR
POSITION
SWITCH
N/O
REQUEST-
TO-EXIT
SWITCH
EARTH
GROUND
CONNECTION
AUXILIARY OUTPUTS
100mA MAX TO COMMON
2916 TERMINALS
TO POWER SUPPLY
KEY PAD POWER
12-24 VOLTS
AC OR DC
}
+
-
BLACK
RED
AUXILIARY RELAY
2 AMPS @ 28VDC MAX
}
NO
NC
COM
ORG/BLK
BLK/WHT
BRN/YEL
MAIN RELAY
5 AMPS @ 28VDC MAX
}
NO
COM
NC
ORANGE
WHITE
YELLOW
Page 2 of 8