- DL manuals
- Haier
- Air Conditioner
- AC142XCERA
- Installation Manual
Haier AC142XCERA Installation Manual
Summary of AC142XCERA
Page 1
Please read this operation manual before using the air conditioner. Please keep this manual carefully and safely. Ac142xcera ac182xcera no. 0010578101 r410a multi split series room air conditioner intdoor unit installation manual.
Page 2: Contents
Contents cautions ............................................................................... Safety precautions .................................................................. Name of parts.......................................................................... Cleaning and care .............
Page 3: Cautions
1 cautions for the purpose of safety, the air conditioner must be properly grounded in accordance with specifications. Always remember to unplug the air conditioner before opening inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight o...
Page 4: Specifications
All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditoiner. Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner's tubes with sharp...
Page 5: Safety Precautions
Safety precautions warning if the power supply cord of this air conditioner is damaged, it must be replaced by the manufacturer or its authorized service personnel only. Use copper wire only. All the cables shall have got the local authentication certificate. The power supply connects from the outdo...
Page 6: Name of Parts
4 name of parts for the wired control type unit, the unit state should be checked by the the wired controller, instead of the remote receiver; and if you set the timer function, the timer led on the remote receiver will not be on. 1 operating control panel (fig.2) 2 emergency switch 3 remote control...
Page 7: Cleaning and Care
Cleaning and care caution before cleaning the air conditioner ,be sure to turn it off and disconnect the power supply cord. Be sure the intake grill is installed securely. When removing and replacing the air filters, be sure not to touch the heat exchanger, as personal injury may result. Cleaning th...
Page 8: Operation Tips
Operation and performance *heating performance *microcomputer-controlled automatic defrosting heat-pump air conditioners heat your entire room by recirculating air throughout the room, with the result that some time may be required after first starting the air conditioner until the room is heated. T...
Page 9: Installation
Installation warning ! Caution ! Please ask the dealer or specialist to install, never try by the users themselves. After the installation please be sure of the following conditions. Incorrect installation may cause water leaking, shock and fire hazard. Please call dealer to install the air-conditio...
Page 10: Installation Procedures
8 installation procedures selecting the mounting position (1)do not install where there is the danger of com- bustible gas leakage. (2) do not install near heat sources. (3) if children under 10 years old may approach the unit, take preventive measures so that they cannot reach the unit. Install at ...
Page 11: Installation Procedures
Installation procedures open the intake grill and remove the three or four or six screws.(fig. 1) remark: the main unit can be wired before the indoor unit is installed. Select the most appropriate installation order. A. Floor console type 1. Drilling for piping select piping and drain directions.(f...
Page 12: Installation Procedures
Installation procedures select whether the drain hose will be connected to the left or right side.(fig.3) insert the drain hose into the drain pan, then secure the drain hose with a nylon fastener. (fig.6) 2. Installing drain hose (fig. 6) wrap the insulation (drain hose) around the drain hose conne...
Page 13: Installation Procedures
3. Installing brackets install the brackets with nuts, washers and spring washers.(fig. 15) 4. Installing indoor unit bracket (right) bracket (left) installation procedures select piping and drain directions. (fig.11) 1. Drilling for piping insert the anchor bolts into the drilled holes, and drive t...
Page 14: Installation Procedures
12 installation procedures select whether the drain hose will be connected to the left or right side.(fig.3) insert the drain hose into the drain pan, then secure the drain hose with a nylon fastener.(fig.6) wrap the insulation (drain hose)around the drain hose connection.(fig.7) be sure to arrange ...
Page 15: Installation Procedures
13 installation procedures (1) dimension of connecting pipe (2) the maximum length and drop height of connecting pipe cautions for piping connection smear refrigerant oil on the joints of piping and flare. The bending radius shall be as large as possible. Align the pipe center when fastening, and ti...
Page 16: Installation Procedures
Installation procedures how to connect wiring to the terminals a. For solid core wiring (or f-cable)(fig.24a) (1) cut the wire with a wire cutter or wire-cutting pliers, then strip the insulation to about 25mm of the exposed solid wire. (2) using a screwdriver, remove the terminal screw(s) on the te...
Page 17: Installation Procedures
15 installation procedures electrical wiring 1. Indoor unit side (1) remove the electric component box. (2) pull out the electric component box. (3) remove the electric component box cover. Remove the three tapping screws. (1) remove the cord clamp. (2) process the end of the connection cords to the...
Page 18: Installation Procedures
16 (5). Wiring of indoor unit the distance between the signal wires and the power cabes should be at least 50mm. C b a q p 1(l) 2(n) 2(n) 1(l) p q a b c l n c1 c2 (in case of using wired controller) to other indoor unit to wired controller to outdoor unit (p) (q) 1.Incorrect address setting will cau...
Page 19: Installation Procedures
Installation procedures 17 1.There are two methods to set the communication address a. Use the remote controller(default status in first installation). B. Use dip switches on the indoor unit pcb. 2. Address setting procedure when using the remote controller. A. Set the addresses only after the succe...
Page 20: Installation Procedures
Installation procedures 18 4. How to check the addresses? When finish all the above works, please power off and power on again to the whole system but set all the indoor units in standby. Then continously press the emergency switch until you hear the buzzer sound 5 times(pi pi pi pi pi), and then th...
Page 21: Installation Procedures
Installation procedures electrical wiring (1) the power source capacity must be the sum of the room air conditioner current and the current of other electrical appliances. When the current contracted capacity is insufficient, change the contracted capacity. (2) when the voltage is too low and the ai...
Page 22: Installation Procedures
Installation procedures (2) insert the hinges on the bottom of the intake grill into the holes in the base assembly. Then mount the arms to the three areas on the top of the intake grill. Fig. 35 fig. 34 (1) cut the right side of the intake grill. This is only when the pipe exits from the right side...
Page 23: Trouble Shooting
Followings are not problems sound of water flowing is not a problem. Sound of cracking is heard. Smell are generated. During operation, white fog or steam comes out from the indoor unit. No outlet air or fan speed can't be changed in dry mode. In cooling operation, unit switches to blowing operation...
Page 24: Trouble Shooting
Before ask for services, please first check your unit against the following. Air conditioner won't start. Poor cooling or heating is power supply switch turned on? Power supply switch is not set at on. Is city power supply normal? Is leakage current breaker activated? This is very dangerous, please ...
Page 25: Trouble Shooting
23 trouble shooting note: 1. Please contact the installers or distributors when trouble happens to repair it. 2. Turn the power off and power on again, if the failure code recurs, please inform the franchiser. 3. Failrue codes maked with are resumable. Abnormal communication between wired controller...
Page 26
Haier group qingdao haier air conditioner electric co., ltd. Address: haier garden, qianwangang road, economic development zone, qingdao, shandong 266500, p.R.China web site: http://www.Haier.Com.