- DL manuals
- Haier
- Inverter
- AS072XVERA
- Operation And Installation Manual
Haier AS072XVERA Operation And Installation Manual
Summary of AS072XVERA
Page 1
Wall mounted type indoor units r410a multi split series room air conditioner operation & installation manual please read this manual carefully before using this air conditioner. Please keep this manual safely for future use. As072xvera as092xvera as122xvera as182xvera no.0010576789 b.
Page 2: Contents
Contents cautions ............................................................................................. Safety precautions............................................................................... Parts and functions .........................................................................
Page 3: Cautions
Cautions 1 disposal of the old air conditioner before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, wh...
Page 4: Specifications
4. The wiring method should be in line with the local wiring standard. 5. The power cable and connecting cable are self-provided.The requirement of the connecting cable: all the cables shall have got the local authentication certificate. 6. The breaker of the air conditioner should be all-pole switc...
Page 5: Warning!
3 warning! Carefully read the following information in order to operate the air conditioner correctly. Below are listed three kinds of safety cautions and suggestions. Instructions: these information can ensure the correct operation of the machine. Be sure to conform with the following important saf...
Page 6: Cautions!
4 cautions! Conditioner should not be used for any other purpose other than airconditioning. Don't use air-conditioner for any other special purposes, e.G. The preservation and protection of food, animals, plants, pecision apparatus as well as work of art, otherwise the qualities of these stuffs may...
Page 7: Caution !
5 caution ! Please ask the dealer or specialist to install, never try by the users themselves. After the installation please be sure of the following conditions. Safety precautions incorrect installation may cause water leaking, shock and fire hazard. Please call dealer to install the air-conditione...
Page 8: Parts and Functions
Parts and functions 6 front panel air inlet grille louver display board indoor unit front view indoor unit back view signal receiver mounting plate heat preservation pipe connecting pipes drainage pipes.
Page 9: Parts and Functions
7 parts and functions remote controller yr-h65 mode clock used to set correct time. Timer light used to set temp.,temp. Range:16 c~30 c sleep used to select sleep mode hour used to set clock and timer setting. Reset used to reset the controller back to normal condition. Lock used to select timer on,...
Page 10: Operation
8 mode sleep swing clock timer set lock light reset sterilize 1 2 3 health airflow fresh code operation clock set when unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: press clock button, "am"or "pm" flashes. Press or to set ...
Page 11: Operation
Operation auto 2 1 press on/off button unit starts running. The previous status appears on the display (except. Timer, sleep mode) press mode button. For each press, operation mode changes as follows: 4 remote controller press on/off button unit stops running. Press fan,for each press, operation mod...
Page 12: Operation
10 a operation cooling press on/off button unit starts running. The previous status appears on the display (except. Timer, sleep mode) press mode button. For each press, operation mode changes as follows: select temp. Button press temp button every time the button is pressed, temp. Setting increases...
Page 13: Operation
11 a operation dry press on/off button unit starts running. The previous status appears on the display (except. Timer, sleep mode) press mode button. For each press, operation mode changes as follows: select drying operation shows" " dry operation starts select temp. Button press temp button every t...
Page 14: Operation
12 a operation fan press on/off button unit starts running. The previous status appears on the display (except. Timer, sleep mode) press mode button. For each press,operation mode changes as follows: select fan operation shows " ", fan operation starts. Press on/off button unit stops running, and wh...
Page 15: Operation
13 a operation heating press on/off button unit starts running. The previous status appears on the display (except. Timer, sleep mode) press mode button. For each press,operation mode changes as follows: select heating operation " " appears and heating operation starts. Press fan button. For each pr...
Page 16: Operation
14 a operation air flow adjustment swing louvers (vertical louvers) up and down put louvers at up position in cooling and down position in heating mode. This will be helpful to keep an even room temp. Note: in cooling or dry operation, don't put horizontal louvers at downward position for a long tim...
Page 17: Operation
15 a operation sleep remote control unit usage of the sleep function after starting, set the run mode and press the sleep button. Run mode 1. In cooling and dry after starting of the sleep operation, the temperature will be raised for 1 c higher than the set temperature 1 hour later,and be raised fo...
Page 18: Operation
16 a operation timer on/off operation remote control unit timer operation set clock correctly before starting timer operation (refer to page 2) you can let unit start or stop automatically at following times: before you wake up in the morning, or get back from outside or after you fall asleep at nig...
Page 19: Operation
17 a operation timer on-off function remote controller operation timer on-off (1) after unit start, select your desired operation mode. Operation mode will be displayed on lcd. (2) timer mode selection press timer button to change timer mode. Every time the button is pressed, display changes as foll...
Page 20: Operation
18 a operation after turning on the unit and set the desired working mode. Press the health button, the lcd will display " ", the unit begins health operation (start the negative ion generation device). Press the health button again, the " " displayed on the lcd disappears, health operation is cance...
Page 21: Notes For Safety
Notes for safety clean the dust filter periodically: blockage of the dust filter would reduce the cooling and heating effect, consume more power, water would be leaked during cooling, and other failures would also occur. 19 ! ! Use the fuse of required capacity: never use steel wire or copper wire t...
Page 22: Operation and Maintenance
Operation and maintenance 20 emergency and test operation use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed "pi" sound is heard once, which means the start of this operation. In this operation,the system automatically selects the ...
Page 23: Trouble Shooting
21 the followings are not malfuncition hua hua trouble shooting water flowing sound is heard when the air conditoner is started, when the compressor starts or stops during operation or when the air conditioner is stopped,it som- etimes sounds ì bi- bi-î or ìgodo-godoî. It is the flowing sound of the...
Page 24: Trouble Shooting
22 **? On off air does not blow or the fan speed cannot be changed during drying. In dry mode, when room temperature becomes 2 c higher than temperature setting, unit rill run intermittently at lo speed regardless of fan setting during heating,indoor fan is still running even unit is stopped. To get...
Page 25: Customer Need-to-Know
23 customer need-to-know customer need-to-know please install the air conditioner according to the requirements specified in this manual to ensure the air conditioner work well. Be careful not to scratch the surface of the case during moving the air conditioner. Please keep the installation manual f...
Page 26: Instructions to Installation
24 warning this system should be applied to places as office, restaurant, residence and the like. Application to inferior environment such as engineering shop could cause equipment malfunction. Please entrust installation to either the company which sold you the equipment or to a professional contra...
Page 27: Precaution
25 precaution self-contained accessories 3. Accessories for installation name of parts no. A b c d e f non-adhesive tape adhesive tape connecting hose gypsum powder drain hose heat insulation material 2. Preparation for installation installation tools 7 pipe cutter 14 refrigeration oil 6 spanner 13 ...
Page 28: Instructions to Installation
5. Method for cutting and expanding pipes. 26 make a hole of 60mm in diameter, slightly descending to outside the wall. Install piping hole cover and seal it off with putty after installation. 4. Drawing of pipe rear piping draw pipes and the drain hose, then fasten them with the adhesive tape. Left...
Page 29: 7. Other Direction Piping
27 heat insulation material drain hose piping indoor/outdoor electric cable signal wire change-f or-fresh-air tube indoor/outdoor electric cord and drain hose must be bound with refrigerant piping by protecting tape lid for right piping lid for under piping lid for left piping fix with adhesive tape...
Page 30: Instructions to Installation
28 8. Indoor unit communication addresses setting 1.There are two methods to set the communication address a. Use the remote controller(default status in first installation). B. Use dip switches on the indoor unit pcb. 2. Address setting procedure when using the remote controller. A. Set the address...
Page 31: 10.Installation Check
29 9.Installation check and trial operation check the layout of the drain pipe and connection wires, and also the piping and address setting. The drain pipe should be placed underneath, and the connection wires should be placed upside; and the drain pipe especially the section inside the machine and...
Page 32: When Trouble Happens
30 when trouble happens insufficient cooling or heating the operation controller adjusted as required air filter too dirty ? Horizontal swing louver upward ? (in heat mode) any obstacle exists at the air inlet or outlet? Door or window left opened ? Insufficient cooling any other heat sources in the...
Page 33: Failure Code
31 failure code note: 1. Please contact the installers or distributors when trouble happens to repair it. 2. Turn the power off and power on again, if the failure code recurs, please change the indoor unit pcb. 3. Failrue codes maked with are resumable. Trouble shooting failure code (displayed on lc...
Page 34
Haier group qingdao haier air conditioner electric co., ltd. Address: haier garden, qianwangang road, economic development zone, qingdao, shandong 266500, p.R.China web site: http://www.Haier.Com.