Dishwasher installation manual quality • innovation • style model dwl3025.
1 page before using your dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 built-in dishwasher installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 what do i need to have to i...
2 important: read and save these instructions doing so will: make installation easier. Help you in the future if you have questions. Help if you have an electrical inspection. Before using the dishwasher this is the safety alert symbol. This symbol alerts you to potential hazards that may seriously ...
3 you need to • carefully open dishwasher door while someone grasps the rear of the dishwasher. Remove shipping materials and lower rack. Close dishwasher door. Latch the dishwasher door shut. • install this dishwasher as specified in these instructions. • have everything you need (tools, materials,...
4 tools and materials needed all installations a pliers b. Phillips screwdriver c. 5 / 8 ” open end wrench d. Measuring tape or ruler e. 10” adjustable wrench that opens to 1 1 / 8 ” (2.9 cm) f. Flat-blade screwdriver g. Gloves h. Utility knife i. 2 twist-on wire connetors which are the proper size ...
5 in addition for new installations q. Electric drill r. ½”, ¾”and 1½” hole saw bits s. Small tubing cutter t. Wire stripper u. 1½”-2” screw-type clamp if connecting to waste-tee v. Copper tubing ( 3 / 8 ” recommended) or flexible strainless steel braided fill line w. Clamp connector or conduit conn...
6 requirements do not run water drain lines or electrical wiring where they can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must provide clearance between motor and flooring. Do not install dishwasher over carpeted flooring. Protect dishwas...
7 electrical it is the customer’s responsibility: to assure that the electrical installation is adequate and in conformance will all national and local codes and ordinances. You must have: - 120-volt, 60hz, ac-only, 15- or 20-amp., fused electrical supply, and connected to an individual, properly gr...
8 water you must have: - a hot water line with 20-120 psi (138-862 kpa) water pressure. - 120°f (49°c) water at dishwasher. - 3 / 8 ” (0.9 cm) o.D. Tubing with compression fitting or flexible stainless steel braided fill line (½”/1.3 cm) minimum plastic tubing is optional but not recommended). - a 9...
9 cabinet dimensions cut openings in shaded area of cabinet walls or floor as specified in chart: 24” (61 cm)** 3¼” (8.3 cm) 2” (5.1 cm) 6” *** (15.2 cm) 2¾” (7 cm) 3¼” (8.3 cm) 9” (22.9 cm) 5½” (14 cm) 2” (5.1 cm) 10” (25.4 cm) 3¼” (8.3 cm) 2¾” (7 cm) 6” *** (15.2 cm) 2” (5.1 cm) 3¼” (8.3 cm) 24” (...
10 warning electrical shock hazard disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. Do not use an extension cord or adapter plug with this appliance. A. Prepare cabinet 1. Disconnect the power s...
11 helpful tip: wiring the dishwasher will be easier if you route wire into the cabinet opening from the left side. Helpful tip: routing the water line through the left side of cabinet opening will make water connection easier. 3. Direct wire method: cut a ¾” (1.9 cm) hole “c” in righthand cabinet s...
12 7. Measure overall length of copper tubing “g” required. Attach copper tubing to water line with manual shutoff valve. Carefully feed copper tubing through hole in cabinet (copper tubing will bend and kink easily) until it is far enough into the cabinet opening to connect it to dishwasher inlet o...
13 11b. No waste disposer + air gap 1. Cut end of drain hose “i” if needed (do not cut ribbed section). 2. Attach drain hose to air gap “j” with large springtype clamp. If the drain hose was cut, use a 1½” to 2” (3.8 to 5 cm) screw-type clamp*. 3. Use a rubber hose connector* “l” with spring or scre...
Tip over hazard do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. 14 helpful tip: to reduce the vibration of the hose, keep the hose away from the floor and the edge of the hole where it passes through the cabinet. 12. Ins...
15 1. Grasp sides of dishwasher door and put dishwasher on its back. 2. Remove two screws “a” attaching access panel “b” and lower panel “c” to dishwasher using a ¼” hex socket,nut driver or phillips screwdriver. Remove panels and set panels aside on a protective surface. Check that grounding clip “...
16 5. Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed “k” (you need the lowest point). Check chart for that height opening. Put wheels “l” in the required position. Turn both front leveler legs to the same height. Helpful tip: built-up floor...
12. Push bracket into slot “s” on the side of dishwasher,and bend tab in towards the side of the dishwasher so that it keeps the bracket in place. 11. Open dishwasher door and push the plastic buttons “r” out of the side of the tub. Note: save the buttons to cover the holes after dishwasher is insta...
18 13. Check the door spring tension. With another person holding the dishwasher to prevent it from tipping, open and close the door a few times. If the door opens by itself, adjust the door spring tension. To adjust the door spring tension, unhook the spring “t” from the rear leg of dishwasher. Wit...
Helpful tip: built-up floors. Tilt dishwasher backward to move into opening. Once in position, support front of dishwasher by lowering or shimming front feet. 19 helpful tip: it is okay if dishwasher fits tightly into cabinet opening. Do not remove insulation blanket - it reduces the sound level. 18...
20. Check that leveling legs “aa” are firmly against the floor. Close and latch the door, and place level against the front panel “bb”. Check that dishwasher is plumb. Adjust leveling leg or add shims under rear wheel until dishwasher is level. Note: shims must be securely attached to floor to preve...
21 warning electrical shock hazard electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to do so can result in death, fire, or electrical shock. 1. Direct wire method: install strain relief and route direct wire so that ...
4. Reinstall terminal box cover “h” with wires inside terminal box. Go to step 5. The cover must be outside the box on the right side. Make sure no wires are pinched by cover. Do not leave the box without the cover. 22 3. Tighten clamp connector or conduit connector screws “g”. Check that power supp...
10. Use pliers to open clamp “n” and slide clamp onto connector “p” between ribs “o” on connector. 9. Push the drain hose into the connector “p” up to the rib “o” on the drain hose. 8. Place the smaller drain hose clamp “n” onto the small end of the drain hose “o”. Remove the plug from the connector...
24 warning tip over hazard do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. D. Secure dishwasher 1. Open dishwasher door and place towel “a” over pump assembly and spray arm of dishwasher. This will prevent screws from fa...
25 e. Check operation 4. Check that grounding clip “a” is attached to the lower panel. Place the lower panel “b” behind the access panel “c”. Some models have insulation “d” on the access panel which must fall behind the insulation “e” on the lower panel. Hold the two panels together and place them ...
52 side view model dwl3025 25” (63,5 cm) 21”(53.3cm) 33 7 / 8 “ (86 cm) minimum with wheels removed ¾”(1.9cm) insulation may be compress -ed..
Made in china haier america new york, ny 10018 printed in china part no. 0120504139b dwl3025dbww/dbbb/sbss issued:-xqh 09 important do not return this product to the store if you have a problem with this product,please contact the “haier customer satisfaction center” at 1-877-337-3639. Dated proof o...
