I3 International Ax48DC2 Quick Start Manual - Quick Start Guide
QUICK START GUIDE
Page -2-
Ax48DC Covert IP Camera
Rev.
160826
CAMERA INSTALLATION
• Depending on the type of installation, additional mounting accessories may need to be
purchased.
• It is the installer’s responsibility to ensure that the mounting surface is suitable for the
chosen installation method.
• Based on installation location and surface type, supplied screws and anchors may not
be adequate. Mounting hardware is site-specific and may need to be supplied by the
installer.
• The camera can be used on its own for covert installations or with the dome cover for
ceiling door count installations.
• Follow Camera network infrastructure diagram below as a general installation guideline.
No. Description
10
DC 12V Power Input. Connect the PoE Gigabit Splitter power cable.
11
LAN Port. Connect one end of the second CAT5/6 cable (not supplied) to
DATA(OUT) RJ45 port on the Splitter and the other end to the LAN RJ45 port
on the Main Unit.
12
Mounting plate, attached to the Main Unit. If your camera comes with mount-
ing plate not attached to the main unit, use a small Phillips screwdriver to
secure the plate to the main unit with four small black screws (provided).
13
Wall Mounting Bracket (Attach to the wall, then slide into the mounting plate
on the main unit)
14
Camera with RJ12 cable. Connect to the VIN1 port on the Main Unit.
Use the adhesive strip provided to attach the camera to the wall (optional).
15
Dome cover (Optional). Fit over the camera, if using.
16
PoE Gigabit Splitter. POWER+DATA (IN) port.
Connect one end of the first CAT5/6 cable (not supplied) to the POWER+DATA
(IN) RJ45 port on the Splitter and the other end to the Gigabit switch.
17
PoE Gigabit Splitter. Output Power (12V) port. Connect the green terminal end
of the Power Cable (#19) to the Output Power (12V) port.
18
PoE Gigabit Splitter. DATA(OUT) RJ45
Connect one end of the second CAT5/6 cable (not supplied) to DATA(OUT)
RJ45 port and the other end to the LAN RJ45 port on the Main Unit (#11).
19
PoE Gigabit Splitter Power Cable.
Connect the green terminal end of the to the Output Power (12V) port on the
Splitter (#17). Connect the other end of the Power Cable to the DC 12V port on
the Main Unit (#10).
CAMERA NETWORK INFRASTRUCTURE
POE Switch
i3 Server (VMS)
Network
RJ45
POE Splitter
(SP12)
Network RJ45
12V DC
8m (26ft) RJ12,
provided)
Ax48DC2/Ax48DC3
Camera
Covert Surveillance
Ax48DC2/Ax48DC3
Main Unit
Network
RJ45
POE Splitter
(SP12)
Network RJ45
12V DC
8m (26ft) RJ12,
provided)
Ax48DC2/Ax48DC3
Main Unit
Ax48DC2 (2.1mm lens, low ceiling install: 8-10 m (26-32 ft) AFF);
Ax48DC3 (2.8mm lens, high ceiling install: 10-14 m (32-46ft) AFF)
Ax48DC2/Ax48DC3 Camera
Door Count
CONNECT CAMERA TO i3 SRX-PRO SERVER
1. Close SRX-Pro Server software by pressing Alt+Shift+Ctrl+F4.
2. Write down the IP address of the onboard NIC (LAN) (or of NIC1 if your SRX-Pro
Server has two onboard NIC cards).
3. Connect your camera to i3 Server (see Camera Network Infrastructure diagram).
4. Turn on your Annexxus 48DC camera.
5. Launch the CD that came with your Annexxus camera and double-click
“
AnnexxusConfigurationTool.msi” file to install Annexxus Configuration Tool
(ACT) application. ACT application discovers all Annexxus cameras connected to
your network.
6. Follow the ACT installation instructions until the application has been successfully
installed on your SRX-Pro Server.
7. Double-click i3 Annexxus Configuration Tool icon on the Desktop to launch
the ACT application. Accept the ACT license agreement.
8. ANNEXXUS Configuration Tool window will display a list of active network
cameras.
Camera’s default IP:
192.168.1.64. Default Login / PW: i3admin / i3admin
9. Select the desired Annexxus camera in the list (left-click).
10. In the Device(s) Communication area, enter the new IP Range (address) and
Subnet Mask of the camera. The new camera IP address must match the IP range
of your SRX-Pro LAN or NIC1 card (see Step 2).
E.g. If your SRX-Pro Server’s IP address is 192.138.10.122, change your Annexxus
camera’s IP address to 192.138.10.XXX. Remember: Annexxus Cameras cannot
share an IP address, each camera requires its own unique IP address.
Change Camera’s Default IP
Please Note: Scan the QR code to the right or visit www.i3international.com to view and download the full User Manual for this
camera. Also available for download is the
AnnexxusConfigurationTool or ACT program used to locate and configure your
cameras with your SRX-Pro software. This program is already installed in SRX-Pro v3.3.3.69 and higher. Please contact our
Technical Support team if you have any questions or concerns regarding camera installation or you require software services or
support. Technical support can be reached by email at:
support@i3International.com or by phone toll free 1.877.877.7241.
QR Code to
Complete
User Manual
/ ACT