Summary of GT-3
Page 1
User manual serious connections tm gt-3 & gt-3st gas tool.
Page 2: A. The Use of Internal
Serious connections tm iccons™ gas tool gt-3 & gt-3st user manual 2 a. The use of internal combustion, gas operated nailer tool the iccons ™ gas nailer is referred to as “tool” in this general safety instruction. Iccons ™ pty ltd is referred to as “manufacturer” in this general safety instruction. I...
Page 3: B. The Use of Fuel Cell
Serious connections tm 3 iccons™ gas tool gt-3 & gt-3st user manual - when using the tool, the operator and any bystanders must wear appropriate eye and ear protection. - when not in use, remove the battery, fuel cell and fasteners, return the fastener follower to guide locking position, and return ...
Page 4: Transport
Serious connections tm iccons™ gas tool gt-3 & gt-3st user manual 4 the cartridge. Transport transport of small amount in a private vehicle ( a transport and safety sheet. The regulations by transport categories are: - road/rail: adr – rid – un code 1950 class 2 code 5f - sea: imdg – un code 1950 + ...
Page 5: Safety For Handling Battery
Serious connections tm 5 iccons™ gas tool gt-3 & gt-3st user manual - this appliance is not intended for use by person (including children) with reduced physical, sensory and metal capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning us...
Page 6: C. Fastener
Serious connections tm iccons™ gas tool gt-3 & gt-3st user manual 6 pressure 18 bar capacity 1,000 shots caution! The fuel cell is always pressurized with propellant to sustain the fuel supply to the metering valve, even the fuel is used up. Its contents are extremely flammable. The fuel cell is not...
Page 7: Battery
Serious connections tm 7 iccons™ gas tool gt-3 & gt-3st user manual b. Installing and removing the battery steps: 1. Empty fasteners from the magazine and make sure the trigger is not pulled while installing the battery. 2. To install the battery, insert the battery cartridge until hearing a “click”...
Page 8: D. Preparing The Fuel Cell
Serious connections tm iccons™ gas tool gt-3 & gt-3st user manual 8 d. Preparing the fuel cell caution ! • never attempt to use fuel cell from other manufacturer. • do not remove the cap when it is unused. • never drill a hole on the fuel cell. • do not inhale the gas. Breathing in the gas could cau...
Page 9: G. Driving The Pins
Serious connections tm 9 iccons™ gas tool gt-3 & gt-3st user manual and release it gently. 4. For removing the pins, lock the follower at the magazine bottom and the pins will slide down. Further pull the follower for releasing all the pins. G. Driving the pins caution ! • please read and understand...
Page 10: I. Adjust The Driving Depth
Serious connections tm iccons™ gas tool gt-3 & gt-3st user manual 10 i. Adjust the driving depth caution ! • please read and understand the section 1 “general safety instructions” for personal and working environment safety. • never press the pin guide by bare hand or by any parts of the body. • nev...
Page 11: Symptom 3
Serious connections tm 11 iccons™ gas tool gt-3 & gt-3st user manual symptom 3 red and green leds on charger are blinking simultaneously. Symptom 1 fan does not run. Symptom 2 fan does not run, or runs slower than normal. Possible reasons services battery is hot. Remove battery from charger and allo...
Page 12: Symptom 2
Serious connections tm iccons™ gas tool gt-3 & gt-3st user manual 12 possible reasons services cylinder head o-ring pinched. Contact authorized serviceman for repair. Jammed fasteners. Clear jam according to user manual. Symptom 2 failure to install fasteners to nose piece. Possible reasons services...
Page 13: Symptom 3
Serious connections tm 13 iccons™ gas tool gt-3 & gt-3st user manual follower holding wrong at the top of the pin strip. Slide follower holder gently to the bottom and release to reset the pin strip in the magazine. Jammed fasteners clear jam according to user manual. Possible reasons services fuel ...
Page 14: 5 - Parts List
Serious connections tm iccons™ gas tool gt-3 & gt-3st user manual 14 5 - parts list.
Page 15
Serious connections tm 15 iccons™ gas tool gt-3 & gt-3st user manual pos. Code description thread lock pos. Code description thread lock 1 nb1010 pin guide 56 nb1600 air dam 2 nb1390 guide sleeve 57 nb1590 u-wire 3 nb140b spring dial 60 nb1610 head o-ring 4 nb142a rear sleeve 61 nb1620 blade assembl...
Page 16
Iccons pty ltd 12-18 produce drive dandenong south victoria, 3175 australia tel: +61 (03) 9706 4344 fax: +61 (03) email: info@iccons.Com.Au web: www.Iccons.Com.Au this manual must be observed when using the tool. All product designations and brand names are the property of their owners and are not e...