1. DL manuals
  2. Icom
  3. Two-Way Radio
  4. IC-A24
  5. Instruction Manual

Icom IC-A24 Instruction Manual

Manual is about: VHF AIR BAND TRANSCEIVER

Summary of IC-A24

  • Page 1

    Instruction manual ia6 ia24 vhf air band transceiver this device complies with part 15 of the fcc rules. Operation is subject to the condition that this device does not cause harmful inter- ference. Ic-a24 ic-a6.

  • Page 2

    I safety training information w arning your icom radio generates rf electromagnetic energy during transmit mode. This radio is designed for and classified as “occupational use only”, meaning it must be used only dur- ing the course of employment by individuals aware of the hazards, and the ways to m...

  • Page 3

    Ii foreword thank you for purchasing this icom product. The ic-a24/a6 vhf air band transceiver is designed and built with icom’s state of the art technology and craftsmanship. With proper care this product should provide you with years of trouble-free operation. Important read all instructions caref...

  • Page 4

    Iii r danger! Never short the terminals of the battery pack. Also, current may flow into nearby metal objects, such as a necklace, etc. Therefore, be careful when carrying with, or placing near metal objects, carrying in handbags, etc. R danger! Use and charge only specified icom bat- tery packs wit...

  • Page 5

    Iv safety training information ............................................... I foreword .................................................................................. Ii important ................................................................................... Ii explicit definitions .........

  • Page 6: Panel Description

    1 1 panel description ■ panel description e r t u y i o microphone speaker !6 !5 !7 q w !1 !0 !2 !3 !4 wx-alert ic-a24 !7 wx-alert !7 ic-a6.

  • Page 7

    2 1 q backlight switch [light] turns the backlight for display and keypad on or off. W ptt switch [ptt] (p. 9) hold down to transmit; release to receive. • “ ” appears on the function display while transmitting. E volume [vol] (p. 9) adjusts the audio level. R tuning dial [dial] (pp. 8–12) ➥ rotate ...

  • Page 8

    3 1 panel description !1 clear key [clr• del ] (pp. 8–17) ➥ push to return to the frequency mode, when memory channel, wx channel, 121.5 mhz, squelch level setting or beep tone setting is se- lected. ➥ push , then hold down [clr• del ] to delete a recall frequency data. ➥ push to clear the entered c...

  • Page 9

    4 1 panel description 1 !7 digit keys ➥ input the specified digit during frequency input, mem- ory channel selection, etc. ➥ in addition, each key has one or more secondary func- tions after pushing as follows: push , then push [0• bank ], and rotate [dial] to select the memory bank number during me...

  • Page 10: Function Display

    5 1 panel description ■ function display q function indicator (p. 2) appears when is pushed. W tx indicator (p. 9) appears while transmitting. E rx indicator (p. 9) appears when receiving a signal, or when the squelch opens. R duplex indicator (ic-a24 only)(p. 24) ➥“dup” appears when the duplex func...

  • Page 11

    6 1 panel description 1 i tag channel indicator (p. 17) “ ” appears when the selected memory channel is set as a tag channel. O memory channel indicator (pp. 12–15) shows the selected memory channel number. !0 memory bank number indicator (p. 12) shows the selected memory bank number. !1 overflow in...

  • Page 12: Accessory Attachment

    7 d antenna caution: do not transmit without an antenna. Other- wise the transceiver may be damaged. Insert the supplied antenna into the antenna connector and screw down the antenna as shown below. D belt clip conveniently attaches to your belt. Attach the belt clip with the supplied screws as belo...

  • Page 13: Basic Operation

    8 3 basic operation ■ setting a frequency ï using keypad q push [pwr] for 2 sec. To turn power on, then push [clr• del ] to select the frequency mode when memory ch number or wx ch number appears on the function display. W push 5 appropriate digit keys to input the frequency. • push [1• dvor ] as th...

  • Page 14: Receiving

    9 3 basic operation ■ receiving q push [pwr] for 2 sec. To turn the power on. W push [sql• wx-alert ], then rotate [dial] counterclock- wise to select the squelch level 0. E rotate [vol] to adjust the audio level. R push [sql• wx-alert ], then rotate [dial] clockwise until the noise is muted. • “ ” ...

  • Page 15: Low Battery Indicator

    10 3 basic operation ■ low battery indicator low battery indicator appears when the battery power has de- creased to a specified level. The attached battery pack requires recharging. ■ recall function the recall function stores the last 10 frequencies used. The function stores frequencies when the f...

  • Page 16: Accessing The 121.5 Mhz

    11 3 basic operation ■ setting weather alert function an noaa broadcast station transmits a weather alert tone before any important weather announcements. When the weather alert function is turned on, the transceiver detects the alert, and sounds a beep tone until the transceiver is op- erated. The ...

  • Page 17: Memory Operation

    12 4 memory operation ■ memory channel selection the transceiver has 200 memory channels for storage of often-used frequencies, along with 6-character notes. Q push [mr• mw ] to select the memory mode. • the memory bank number and memory ch number appears. Using [dial]: w push , then push [0• bank ]...

  • Page 18: Programming A Memory

    13 4 memory operation ■ programming a memory channel the transceiver has 200 (20 ch × 10 bank) memory chan- nels for storage of often-used frequencies. Q push [clr• del ] to select the frequency mode, if neces- sary. W select the desired frequency. • push , then push [ent• wx ] to select a weather c...

  • Page 19: Memory Names

    14 4 memory operation ■ memory names ï programming memory names the memory channel can display a 6-character name in- stead of the programmed frequency. Q in the frequency mode, rotate [dial] to select the desired frequency in the frequency mode. W push , then push [mr• mw ] to program the contents ...

  • Page 20

    15 4 memory operation push push push push push push push push push push push (or rotate [dial]) (or rotate [dial]) • example: programming 125.000 mhz into memory bank 1/ memory channel 17 with “air-23” as a comment. Note: push , then push [0• bank ], and then rotate [dial] to select the bank number,...

  • Page 21: Scan Operation

    16 5 scan operation ■ scan types the u.S.A. Version has 3 scan types to suit your needs. The non-u.S.A. Versions have 2 scan types. ■ com band scan q push [clr•del] to select the frequency mode. W push [sql• wx-alert ], then rotate [dial] to set the squelch level to the point where noise is just mut...

  • Page 22: Weather Channel Scan

    17 5 scan operation ■ weather channel scan (u.S.A. Version only) q push , then push [ent• wx ] to select a weather chan- nel. W set the squelch to the point where noise is just muted. E push , then push [anl• scan ] to start the scan. • when a signal is received, the scan pauses until it disappears....

  • Page 23: Vor Navigation (Ic-A24 Only)

    18 6 vor navigation (ic-a24 only) ■ vor indicators 214 34 from com band (118.000 136.975 mhz) nav band (108.000 117.975 mhz) dvor mode function display of the ic-a24 general vor equipment to-from flag indicator cdi mode course indicator course indicator course deviation needles overflow indicator pu...

  • Page 24: Vor Functions

    19 6 vor navigation (ic-a24 only) ■ vor functions d to select the cdi mode to show the deviation between your flying course and the desired course, push , then push [4• cdi ] to select the cdi mode. D to select the dvor mode when entering the nav band, 108.000–117.975 mhz, the ic-a24 selects the dvo...

  • Page 25: Flying to A Vor Station

    20 6 vor navigation (ic-a24 only) ■ flying to a vor station the ic-a24 shows the deviation from a vor station. Q select a vor station on your aeronautical chart and push the keypad or rotate [dial] to set the frequency of the station. • the course indicator indicates where you are located on a ra- d...

  • Page 26

    21 6 vor navigation (ic-a24 only) vor station 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 n magnetic north desired course aircraft heading 40 123.65 vortac seattle 116.8 ch 115 sea the aircraft is on course vor ...

  • Page 27: Entering A Desired Course

    22 6 vor navigation (ic-a24 only) ■ entering a desired course the ic-a24 shows not only the deviation from the vor sta- tion but the deviation from the desired course. Q push the keypad or rotate [dial] to set the frequency for the desired vor station. • push , then push [2• to ] or [3• from ] to ch...

  • Page 28

    23 6 vor navigation (ic-a24 only) example: entering the desired course bearing 65° to a vor station. Vor station 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 n magnetic north vor station 0 10 20 30 40 50 60 70 80...

  • Page 29: Duplex Operation

    24 6 vor navigation (ic-a24 only) ■ duplex operation (u.S.A. Version only) the duplex function allows you to call a flight service station while receiving a vor station. The duplex function requires frequency programming for the flight service station in ad- vance. D programming a duplex frequency q...

  • Page 30: Battery Packs

    25 7 battery packs ■ battery charging prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. Caution: to avoid damage to the transceiver, turn the power off while charging. • recommended temperature range for charging: +10°c to +40°c...

  • Page 31: Optional Battery Case

    26 7 battery packs d regular charging q attach the battery pack to the transceiver. W be sure to turn the transceiver power off. E connect the wall charger or optional cable (cp-20) as shown below. R charge the battery pack approximately 8 hours, depend- ing on the remaining power condition. Do not ...

  • Page 32: Optional Battery Chargers

    27 7 battery packs ■ optional battery chargers d ad-101 installation the ad-101 charger adapter must be installed into the bc-119n or bc-121n before battery charging. Connect the ad-101 charger adapter and the bc-119n/ bc-121n as below (q), then install the ad-101 into the holder space of the bc-119...

  • Page 33

    28 d rapid charging with the bc-119n+ad-101 the optional bc-119n provides rapid charging of the battery packs. The following are additionally required. • ad-101 charger adapter. • an ac adapter (may be supplied with bc-119n depending on ver- sions) or the dc power cable (cp-20). D rapid charging wit...

  • Page 34: Cloning

    29 8 cloning cloning allows you to quickly and easily transfer the programmed data from one transceiver to another transceiver, or, data from a pc to a transceiver, using the optional cs-a24 cloning software. D transceiver to transceiver cloning q connect the opc-474 cloning cable with adapter plugs...

  • Page 35: Troubleshooting

    30 9 troubleshooting if your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. 9 10 fuse 8 a d cp-20 fuse replacement if the fuse blows or the receiver stops functioning while operating with the optional cp-20 cigarette lighter cable , f...

  • Page 36: Specifications

    31 10 specifications d general • frequency coverage (mhz) : tx 118.000 to 136.975 rx 108.000 to 136.975* 1 wx 161.650 to 163.275* 2 • mode : 6k00a3e 16k0g3e (161.65 to 163.275 mhz)* 2 • channel spacing : 25 khz • number of memory channels : 200 (20 ch × 10 banks) • power supply requirement : specifi...

  • Page 37: Options

    D battery case and packs • bp-208n battery case battery case for 6 × aa (lr6) alkaline cells. • bp-209n ni-cd battery pack 7.2 v/1100 mah ni-cd battery pack. • bp-210n ni-mh battery pack 7.2 v/1650 mah ni-mh battery pack. D chargers • bc-167sa/sd/sc/sv wall charger the same as supplied with the tran...

  • Page 38: Optional Headset Connection

    33 12 optional headset connection d opc-499 ( headset adapter) connection when using a headset (3rd party products) via the opc-499 headset adapter , the transceiver outputs your transmitted voice to the headset for monitoring. See “■ side tone function” (p. 11) when setting the side tone level. Ptt...

  • Page 39

    34 12 13 memo.

  • Page 40

    1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan printed on recycled paper with soy ink. A-6403d-1ex-i printed in japan © 2004–2010 icom inc..