- DL manuals
- Icom
- Two-Way Radio
- IC-F1020
- Instruction Manual
Icom IC-F1020 Instruction Manual
Summary of IC-F1020
Page 1
Instruction manual ic- f1020 vhf land mobile radio ic- f2020 uhf land mobile radio this device complies with part 15 of the fcc rules. Operation is subject to the condition that this device does not cause harmful interference..
Page 2
I r warning! Never connect the transceiver to an ac outlet. This may pose a fire hazard or result in an electric shock. Never connect the transceiver to a power source of more than 16 v dc such as a 24 v battery. This connection will ruin the transceiver. Never cut the dc power cable between the dc ...
Page 3
Ii table of contents important ........................................................................ I explicit definitions ..................................................... I cautions ........................................................................... I table of contents ...............
Page 4: Panel Description
P 0 p 1 p 2 p 3 volume control microphone connector function display speaker power switch programmable function keys programmable function keys panel description 1 1 ■ front panel.
Page 5: Programmable Function Keys
■ programmable function keys the following functions can be assigned to programmable function keys. Assigned function names can be affixed to the lcd using supplied stickers. Channel up and down keys • select an operating channel • select a bank after pushing the [ bank s ] key. • select a dtmf chan...
Page 6
1 scan tag key adds or deletes the selected channel to the scan group. • “ ” appears above the [ tag ] key when the channel be- longs to the scan group. Priority channel key selects a priority a or priority b channel with each push. Lock key electronically locks all programmable keys except the [ mo...
Page 7
1 4 talk around key turns the talk around function on and off. • the talk around function equalizes the transmit frequency to the receive frequency for mobile-to-mobile communica- tion. Emergency key push and hold the key to transmit an emergency call. • an emergency call is transmitted for a specif...
Page 8: Function Display
Busy indicator appears while the channel is busy. Transmit indicator appears while transmitting. Audible indicator appears when monitor function is turned off (ctcss and dtcs mutes are released). Activated key indicator appears or blinks when the key under this indicator is activated. Bell indicator...
Page 9: Turning Power On
■ turning power on q push [k i ] to turn the power on. • a power-up alert tone sounds for about 1 sec. And an opening mes- sage may appears. W if the transceiver is programmed for start up passcode, input digit codes as directed by your sys- tem operator. • the following keys can be used for the pas...
Page 10: Receiving and Transmitting
■ receiving and transmitting receiving: q push [k i ] to turn the power on. W push [ ch up ] or [ ch dn ] to select a channel. E when receiving a signal, adjust the volume to a comfort- able listening level. Transmitting: r hung off the microphone from the microphone hanger: • ctcss or dtcs may be r...
Page 11
2 8 d dtmf transmission if the transceiver has [ dtmf ] key, the automatic dtmf trans- mission function is available. Up to 7 dtmf channels may be available. Q push [ dtmf ] to select the display as at right. W push [ ch up ] or [ ch dn ] to select the desired dtmf channel. E push and hold [ dtmf ] ...
Page 12: Connection and Installation
¤ ⁄ ‹ › fi 12 v battery black: . Red: , optional speaker (sp-10) optional cable (opc-617) antenna supplied dc power cable connection and installation 3 9 ■ rear panel and connection.
Page 13: Unpacking
3 connection and installation 10 ⁄ antenna connector connects to an antenna. Ask your dealer about antenna selection and best installation location. ¤ microphone hanger connect the supplied microphone hanger to the vehicle’s ground for hanger function when hanging or releasing the microphone. ‹ dc p...
Page 14: Mounting
3 connection and installation 11 ■ mounting ■ separation q separate the front panel from the transceiver main unit using an allen-wrench (1/32 in). W connect the optional separation cable to the both front and main unit attachments (fig. 1 and 2). • remove the rear plate of the attachment. • use the...
Page 15: Optional Ut-105 Installation
3 connection and installation 12 ■ optional ut-105 installation the optional ut-105 provides smartrunk ii™ functions. In- stall the unit as follows: q turn power off, then disconnect the dc power cable. W unscrew the 4 screws, then remove the bottom cover. E install the unit as shown in the diagram ...
Page 16: Smartrunk Ii™ And
Optional smartrunk ii™ operation 4 13 ■ smartrunk ii™ and conventional modes this transceiver meets to smartrunk ii™ functions. The optional ut-105 allows communication in conventional channels or smartrunk ii™ channels. Select a channel bank for smartrunk ii™ before trunking operation. • push [ bk ...
Page 17
4 optional smartrunk ii™ operation 14 d terminating a call after completing a call, push [#] to disconnect (hang up). Important: if one person in the conversation terminates a call, all participants will be cut off. D last number redial push [ m ], [ m ] to automatically redial the last number calle...
Page 18
4 optional smartrunk ii™ operation 15 d clear channel alerting if all channels are busy, the transceiver automatically begins searching for an open channel and beeps every ten seconds. When two short beeps (low-pitched, then high-pitched) are heard, a channel is available. Push [ m ], [ m ] immediat...
Page 19: Options
Options 5 external speakers sp-5 large speaker for good audio quality. Input impedance: 4 Ω max. Input power: 5 w sp-10 compact and easy-to-install. Input impedance: 4 Ω max. Input power: 5 w rmk-1 separation kit and separation cable allows you for separate installation of the transceiver main unit ...
Page 20
A-5441s-1us printed in japan copyright © 1995 by icom inc. 6-9-16 kamihigashi, hirano-ku, osaka 547 japan.