- DL manuals
- Icom
- Transceiver
- IC-F110
- Instruction Manual
Icom IC-F110 Instruction Manual
Summary of IC-F110
Page 1
If110 vhf transceiver instruction manual if210 uhf transceiver ic-f110_f210_eur-1.Qxd 03.2.5 3:30 pm page a (1,1).
Page 2
I important explicit definitions rwarning! Never connect the transceiver to an ac outlet. This may pose a fire hazard or result in an electric shock. Never connect the transceiver to a power source of more than 16 v dc such as a 24 v battery. This connection will ruin the transceiver. Never cut the ...
Page 3
Ii do not use or place the transceiver in areas with tem- peratures below –25°c or above +55°c, or in areas subject to direct sunlight, such as the dashboard. Avoid operating the transceiver without running the vehi- cle’s engine. The vehicle’s battery will quickly run out if the transceiver transmi...
Page 4: Panel Description
1 1 panel description y t r q w e ■front panel qaf volume control knob rotate the knob to adjust the audio output level. • minimum audio level is pre-programmed. Wfunction display displays a variety of information, such as an operating channel number/name, 5-tone code, dtmf numbers and audible condi...
Page 5: ■Function Display
2 1 panel description tdealer-programmable keys [p0] to [p3] desired functions can be programmed independently by your dealer. Ymicrophone connector connect the supplied microphone or optional dtmf micro- phone for smartrunk ii tm operation here. Never connect non-specified microphones. The pin assi...
Page 6
3 1 panel description u2/5tone indicator appears when the specified 2/5-tone call is received. I alphanumeric display displays the ch number, 5-tone indication, dtmf num- bers, audible indication, etc. Note: when the alphanumeric display blinks and trans- mitting becomes impossible, check that the d...
Page 7
4 1 panel description ¡ ¡ scan start/stop key push this key to start scanning; and push again to stop. Note: place the microphone on hook to start scanning. Take the microphone off hook to stop scanning. ¡ ¡ scan tag key adds or deletes the selected channel to the scan group. ¡ ¡ priority channel ke...
Page 8
5 1 panel description ¡ ¡ output power selection keys select the transmit output power temporarily, or permanently, depending on the pre-setting. • contact your dealer for the output power level for each selection. ¡ ¡ talk around key turns the talk around function on and off. • the talk around func...
Page 9
6 1 panel description ¡ ¡ scrambler key ➥ push and hold to turn the voice scrambler func- tion on. ➥ push this key to turn the voice scrambler func- tion off. Note: • the optional ut-109 (#02) or ut-110 (#02) voice scrambler unit is required. – ut-109: non-rolling type. 32 codes are available. – ut-...
Page 10: Operation
7 2 operation ■turning power on q push [ ] to turn the power on. W if the transceiver is programmed for a start up passcode, input the digit codes as directed by your dealer. • the keys in the table below can be used for password input: • the transceiver detects numbers in the same block as identica...
Page 11
8 2 operation ■receiving and transmitting receiving: q push [ ] to turn the power on. W push [ ] and [ ] to select a channel. E when receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: r take the microphone off hook. • 2-tone, 5-tone mute may be released. ...
Page 12
9 2 operation d tx code channel selection if the transceiver has a [tx ch] key, the display can be tog- gled between the operating channel number (or name) and tx code channel number (or name). When the tx code channel number (or name) is displayed, the [ ]/[ ] keys select the tx code channel. To se...
Page 13
10 2 operation d user set mode user set mode is accessed at power on and allows you to set seldom-changed settings. In this case you can “cus- tomize” transceiver operation to suit your preferences and operating style. Entering the user set mode: q while pushing and holding [ ] and [ ], push [power]...
Page 14: ■Smartrunk Ii™ And
11 3 optional smartrunk ii™ operation ■smartrunk ii™ and conventional modes this transceiver is capable of smartrunk ii™ functions. The optional ut-105 allows communication in conventional channels or smartrunk ii™ channels. Select a channel bank for smartrunk ii™ before trunking operation. • push [...
Page 15
12 3 optional smartrunk ii™ operation d terminating a call after completing a call, push [#] to disconnect (hang up). Important!: if one person in the conversation termi- nates a call, all participants will be cut off. D last number re-dial push [m] 2 times to automatically re-dial the last called n...
Page 16: Connection And Maintenance
13 4 connection and maintenance optional speaker (sp-22) optional cable (opc-617) antenna never connect to a 24 v battery. + red: black: 12v battery solder crimp note: use the terminals as shown below for the cable connections. R c a u t i o n ! N e v e r r e- move the fuse-holder from the dc power ...
Page 17: ■Supplied Accessories
14 4 connection and maintenance q antenna connector connects to an antenna. Contact your dealer about an- tenna selection and placement. W microphone hanger connect the supplied microphone hanger to the vehicle’s ground for microphone on/off hook functions. (see p. 2) e dc power receptacle connects ...
Page 18: ■Mounting The Transceiver
15 4 connection and maintenance ■mounting the transceiver the universal mounting bracket supplied with your transceiv- er allows overhead mounting. • mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. Flat washer spring washer when using ...
Page 19: ■Optional Ut-109 Or Ut-110
16 4 connection and maintenance ■optional ut-109 or ut-110 installation q turn the power off, then disconnect the dc power cable. W unscrew the 4 cover screws, then remove the bottom cover. E cut the pattern on the pcb at the tx mic circuit (mic) and rx af circuit (disc) as shown below. R install th...
Page 20: ■ Antenna
17 4 connection and maintenance ■ antenna a key element in the performance of any communication sys- tem is an antenna. Contact your dealer about antennas and the best places to mount them. ■ fuse replacement a fuse is installed in the supplied dc power cable. If a fuse blows or the transceiver stop...
Page 21: Options
18 5 options sp-22 external speaker compact and easy-to-install. Input impedance : 4 Ω max. Input power : 5 w hm-100tn dtmf microphone. Sm-25 desktop microphone. Ut-105 smartrunk ii tm logic board provides smartrunk ii tm capabilities. Ut-108 dtmf decoder unit provides pager and code squelch capabil...
Page 22: 0168
19 6 ce ce versions of the ic-f110s/210s which display the “ce” symbol on the serial number seal, com- ply with the essential requirements of the european radio and telecommunication terminal directive 1999/5/ec. This warning symbol indicates that this equip- ment operates in non-harmonised frequenc...
Page 23: 0168
20 6 ce declaration of conformity we icom inc. Japan 1-1-32, kamiminami, hirano-ku osaka 547-0003, japan kind of equipment: uhf transceiver this compliance is based on conformity with the following harmonised standards, specifications or documents: i) en 301 489-1 (august 2000) ii) en 301 489-5 (aug...
Page 24
1-1-32 kamiminami, hirano-ku, osaka 547-0003 japan a-6234h-1eu-q printed in japan © 2002–2003 icom inc. Ger aut gbr irl nor fra ned bel lux esp por ita gre swe den fin sui ic-f110_f210_eur-1.Qxd 03.2.5 3:31 pm page z (1,1).