- DL manuals
- Icom
- Transceiver
- IC-F3022S
- Instruction Manual
Icom IC-F3022S Instruction Manual
Summary of IC-F3022S
Page 1
Instruction manual if3022t/s vhf transceivers the photo shows the 10-key version vhf transceiver. If4022t/s uhf transceivers.
Page 2
Precautions i r caution! Never hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical. R ca...
Page 3
Ii do not modify the transceiver for any reason. Keep the transceiver from the heavy rain, and never immerse it in the water. The transceiver construction is water resistant, not waterproof. The use of non-icom battery packs/chargers may impair transceiver performance and invalidate the warranty..
Page 4
Iii important ........................................................................ I explicit definitions ..................................................... I precautions ................................................................... I table of contents .....................................
Page 5: Accessories
1 1 accessories 1 ■ supplied accessories ■ accessory attachments d flexible antenna connect the supplied flexible antenna to the antenna connector. Caution! • never hold the antenna when carrying the transceiver. • transmitting without an antenna may damage the transceiver. Flexible antenna battery ...
Page 6
2 1 accessories ï battery pack to attach the battery pack: slide the battery pack in the direction of the arrow ( q), then lock it with the battery release button. • slide the battery pack until the battery release button makes a ‘click’ sound. To release the battery pack: slide the battery release ...
Page 7
3 1 accessories 1 ï jack cover attach the jack cover when the optional speaker-microphone or headset is not used. To attach the jack cover: q attach the jack cover to the [mic/sp] jack. W tighten the screws. Caution! • attach the jack cover when the optional speaker-micro- phone or headset is not us...
Page 8: Panel Description
4 2 panel description ■ front panel q antenna connector connects the supplied antenna. W dealer-programmable key [emer] desired function can be programmed by your dealer. (p. 7) e dealer-programmable key [side1] desired function can be programmed by your dealer. (p. 7) r ptt switch [ptt] push and ho...
Page 9
5 2 panel description 2 o external microphone/speaker jack connect an optional speaker-microphone or headset. Note: connect or disconnect the optional equipment after the transceiver is turned off. !0 volume control [vol] rotate to turn the power on/off and adjusts the audio level. Jack cover note: ...
Page 10: ■ Function Display
6 2 panel description ■ function display q transmit indicator appears while transmitting. W busy indicator appears while the channel is busy. E signal strength indicator indicates relative signal strength level. R low power indicator appears when low output power is selected. • when the battery powe...
Page 11
7 2 panel description 2 ■ programmable function keys the following functions can be assigned to [emer], [side1], [side2], [side3], [p0], [p1], [p2] and [p3] programmable function keys. Consult your icom dealer or system operator for details con- cerning your transceivers programming. If the programm...
Page 12
8 2 panel description prio a/b keys ➥push to select priority a or priority b channel. ➥push and hold [prio a (rewrite)] or [prio b (rewrite)] for 1 sec. To reassign the operating channel to priority a or priority b channel. Mr-ch 1/2/3/4 keys push to select memory channels 1 to 4 in the operating zo...
Page 13
9 2 panel description 2 surveillance key push to turn the surveillance function on or off. When this function is turned on, the beep is not emitted and the lcd backlight does not light when a signal is received or a key is pushed, etc. Siren key push to emit a siren. Tx code enter key push to enter ...
Page 14: ■ Turning Power On
■ turning power on prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. (p. 16) q rotate [vol] to turn the power on. W if the transceiver is programmed for a start up password, input the digit codes as directed by your dealer. • 10...
Page 15: ■ Channel Selection
11 3 basic operation 3 ■ channel selection several types of channel selections are available. Methods may differ according to your system set up. Non-zone type: push [ch up] or [ch down] to select the desired operating channel, in sequence; or, push one of [mr-ch 1] to [mr-ch 4] keys to select a cha...
Page 16
12 3 basic operation ■ receiving and transmitting note: transmitting without an antenna may damage the transceiver. See (p. 1) for accessory attachments. Receiving: q rotate [vol] to turn the power on. W push [ch up] or [ch down] to select the conventional sys- tem channel, in sequence. E when recei...
Page 17
13 3 basic operation 3 d tx code channel selection if the transceiver has [tx code ch select] assigned to it, the indication can be switched between the operating channel number (or name) and tx code channel number (or name). When the tx code channel number (or name) is displayed, [ch up] or [ch dow...
Page 18: ■ User Set Mode
14 3 basic operation using [tx code enter] key: q select the desired tx code channel via [tx code ch select]+[ch up] or [ch down], [tx code ch up] or [tx code ch down]. (p. 13) w push [tx code enter] to enter the tx code edit mode. E push [tx code enter] several times to select the desired digit to ...
Page 19: ■ Emergency Transmission
15 3 basic operation 3 ■ emergency transmission when [emergency single] or [emergency repeat] is pushed, an emergency signal is automatically transmitted for the spec- ified time period. When [emergency] is pushed, the dtmf emergency signal is transmitted on the priority channel. When [emergency sin...
Page 20: Battery Charging
16 4 battery charging ■caution r danger! Use and charge only specified icom battery packs with icom radios or icom charger. Only icom battery packs are tested and approved for use and charge with icom radios or icom charger. Using third-party or counterfeit bat- tery packs or charger may cause smoke...
Page 21
17 4 battery charging 4 warning! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your icom dealer or distrib- utor. Warning! Immediately wash, using clean water, any part of the body that comes into co...
Page 22
18 4 battery charging ■ optional battery chargers see each instruction manual for details of the charger led indication, operation, etc. ï rapid charging with the bc-160 the optional bc-160 provides rapid charging of optional li- ion battery packs. • an ac adapter (may be supplied with bc-160 depend...
Page 23
19 4 battery charging 4 ï rapid charging with the bc-119n+ad-106 the optional bc-119n provides rapid charging of battery packs. The following items are additionally required. • ad-106 charger adapter • an ac adapter (may be supplied with bc-119n depending on ver- sion) or the dc power cable (opc-515...
Page 24
20 4 battery charging important!: battery charging caution ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. (this illustration is described with the bc-160.) guide rail lobs.
Page 25: Battery Case
21 5 battery case 4 5 ■optional battery case (bp-240) when using the optional battery case, install 6 × aaa (lr03) size alkaline batteries as illustrated at right. Q unhook the battery cover release hook ( q), and open the cover in the direction of the arrow ( w). (fig.1) w then, install 6 × aaa (lr...
Page 26: Optional Swivel Belt Clip
22 6 optional swivel belt clip ■ mb-93 contents qty. Q belt clip ……………………………………………………… 1 w base clip …………………………………………………… 1 ■ attaching q release the battery pack if it is attached. (p. 2) w slide the base clip in the direction of the arrow until the base clip is locked and makes a ‘click’ sound. E ...
Page 27: ■ Detaching
23 6 optional swivel belt clip 6 ■ detaching q turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. W release the battery pack if it is attached. (p. 2) e pinch the clip ( q), and slide the base clip in the direction of the arrow ( w). Caution! Hold the tra...
Page 28: Options
24 7 options d battery pack d chargers •bc-119n desktop charger + ad-106 charger adapter + bc-145 ac adapter for rapid charging of battery packs. An ac adapter is sup- plied with the charger depending on versions. Charging time: approx. 2 hours when bp-231 is attached. •bc-121n multi - charger + ad-...
Page 29
25 7 options 7 d other options • sp-13 earphone provides clear receive audio in noisy environment. • hm-158l/159l speaker - microphone combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt. • hs-94/hs-95/hs-97 headset + vs-1l vox /ptt case hs-...
Page 30: Doc
26 8 doc ce versions of the ic-f3022t/s and the ic-f4022t/s which display the “ce” symbol on the serial number seal, comply with the essential requirements of the european radio and telecommunication terminal directive 1999/5/ec. Declaration of conformity we icom inc. Japan 1-1-32, kamiminami, hiran...
Page 31: 0168
27 8 doc 8 declaration of conformity we icom inc. Japan 1-1-32, kamiminami, hirano-ku osaka 547-0003, japan kind of equipment: uhf pmr transceiver type-designation: ic- f4022t/f4022s signature authorized representative name place and date of issue declare on our sole responsibility that this equipme...
Page 32
1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a-6507d-1eu-q printed in japan © 2006 icom inc. Ger aut gbr irl nor fra ned bel lux esp por ita gre swe den fin sui.