- DL manuals
- Icom
- Transceiver
- IC-F310S
- Instruction Manual
Icom IC-F310S Instruction Manual
Summary of IC-F310S
Page 1
Instruction manual this device complies with part 15 of the fcc rules. Operation is subject to the condition that this device does not cause harmful interference. Vhf transceiver uhf transceiver if320s if310s if410s if420s.
Page 2
I r warning! Never connect the transceiver to an ac outlet. This may pose a fire hazard or result in an electric shock. Never connect the transceiver to a power source of more than 16 v dc such as a 24 v battery. This connection will ruin the transceiver. Never cut the dc power cable between the dc ...
Page 3
Ii table of contents important ........................................................................ I explicit definitions ..................................................... I cautions .......................................................................... I table of contents ................
Page 4: Panel Description
1 1 panel description ■ front panel tx / rx 4 3 2 1 s r microphone connector (p. 2) programmable function keys [p0],[p1],[p2],[p3] (p. 3) e power switch (p. 2) function led (p. 2) w ch up/down keys [ ]/[ ] (p. 3) q volume up/down keys (p. 2).
Page 5: Function Led
1 panel description 2 q volume up/ down keys push to adjust the audio output level. • minimum audio level is pre-programmed. W ch up/down [ ]/[ ] keys • push to select the operating channel. • can be programmed for one of several functions by your- dealer. (see p. 3) e power switch turns the power o...
Page 6: Programmable Function Keys
1 3 panel description call keys transmit a 5-tone call. • call transmission is necessary before you call another sta- tion depending on your signaling system. • the [cal a] and/or [cal b] keys may be available when your system employs selective ‘individual/group’ calls. Ask your system operator whic...
Page 7
1 auto :turns on/off depending on the acc socket pin 1 voltage. On: low (0 v) off: high (12 v) * even when turned off, the led lights slightly. Operating channel keys select an operating channel directly. Output power selection keys select the transmit output power temporarily or per- manently depen...
Page 8
1 panel description 5 trunking group switch push to select the trunking group. Voice scrambler switch • push and hold to turn the voice scrambler function on. • push to turn the voice scrambler function off. Note: • optional ut-109 (#02) or ut-110 (#02) voice scrambler unit is required. • ic-f320(42...
Page 9: Channel Selection
■ channel selection several types are available, and the channel selection method may differ according to your system set up. Non-bank type: push the [ ]/[ ] keys to select the desired operating channel, in sequence; or, push one of the [ ch 1 ] to [ ch 4 ] keys to select these channels directly. Se...
Page 10: Receiving and Transmitting
■ receiving and transmitting receiving: q push [k i ] to turn the power on. W push [ ]/[ ] to select a channel. E when receiving a call, adjust the volume [up] or [down] to a comfortable listening level. Transmitting: r take the microphone off hook. • 5-tone mute may be released. • a priority channe...
Page 11: User Set Mode
2 operation 8 d dtmf transmission if the transceiver has a [ dtmf ] key, the automatic dtmf transmission function is available. D scrambler function a ut-109 (#02) or ut-110 (#02) optional voice scrambler unit provides hight performance private communication between stations with the same scrambler ...
Page 12: Connection and Maintenance
Connection and maintenance 3 9 ■ rear panel and connection antenna red: + black: _ supplied dc power cable optional speaker (sp-10, sp-22) optional cable (opc-617) t q w e r.
Page 13: Supplied Accessories
3 connection and maintenance 10 ⁄ antenna connector connects to an antenna. Ask your dealer about antenna selection and placement. (see p. 12) ¤ microphone hanger connect the supplied microphone hanger to the vehicle’s ground for on/off hook microphone functions. (see p. 2) ‹ dc power receptacle con...
Page 14: Mounting The Transceiver
■ mounting the transceiver the universal mounting bracket supplied with your transceiver allows overhead mounting. Please read the following instruc- tions carefully. • mount the transceiver securely with the 4 supplied screws to a sturdy surface which can support more then 1.5 kg. 3 connection and ...
Page 15: Antenna
3 connection and maintenance 12 ■ antenna a key element in the performance of any communication sys- tem is an antenna. Ask your dealer about antennas and the best places to mount them. ■ fuse replacement two fuses are installed in the supplied dc power cable. If a fuse blows or the transceiver stop...
Page 16: Smartrunk Ii™ And
Optional smartrunk ii™ operation 4 13 ■ smartrunk ii™ and conventional modes this transceiver is capable of smartrunk ii™ functions. The optional ut-105 allows communication in conventional channels or smartrunk ii™ channels. Note: connect an optional hm-100t dtmf micro- phone . Contact your dealer ...
Page 17
4 optional smartrunk ii™ operation 14 d terminating a call after completing a call, push [#] to disconnect (hang up). Important: if one person in the conversation terminates a call, all participants will be cut off. D last number redial push [ m ], [ m ] to automatically redial the last number calle...
Page 18
4 optional smartrunk ii™ operation 15 d clear channel alerting if all channels are busy, the transceiver automatically begins searching for an open channel and beeps every ten seconds. When two short beeps (low-pitched, then high-pitched) are heard, a channel is available. Push [ m ], [ m ] immediat...
Page 19: Options
5 external speakers sp-5 large speaker for good audio quality. Input impedance: 4 Ω max. Input power: 5 w sp-10 compact and easy-to-install. Input impedance: 4 Ω max. Input power: 5 w sp-22 compact and easy-to-install input impedance: 4 Ω max. Input power: 5 w microphones hm-100t dtmf microphone. Hm...
Page 20
6-9-16 kamihigashi, hirano-ku, osaka 547-0002 japan a-5560d-1ex printed in japan © 1998 by icom inc..