1. DL manuals
  2. Icom
  3. Transceiver
  4. IC-F3162DS
  5. Operating Manual

Icom IC-F3162DS Operating Manual

Manual is about: VHF dPMR HANDHELD TRANSCEIVER UHF dPMR HANDHELD TRANSCEIVER

Summary of IC-F3162DS

  • Page 1

    Operating guide operating guide for ic-f3162dt/ds ic-f4160dt/ds biis 1200/dpmr operation.

  • Page 2

    I thank you for purchasing this icom transceiver. The binary interchange of information and signaling (biis) 1200 and digital private mobile radio (dpmr) system func- tions are built into your ic-f3162dt/ds or ic-f4162dt/ds transceiver. Read all instructions carefully and completely before using the...

  • Page 3

    Table of contents ii important .......................................................................... I table of contents ........................................................ Ii 1 preparation............................................................1–2 ■ programmable function keys ...........

  • Page 4: Preparation

    1 1 preparation ■ programmable function keys the following functions can be assigned to [emr], [side1], [side2], [side3], [p0], [p1], [p2] and [p3] programmable function keys. Consult your icom dealer or system operator for details con- cerning your transceiver’s programmed keys and their func- tion...

  • Page 5

    D for both biis 1200 and dpmr operations the following key functions are useful for biis 1200 and dpmr operations. Status up, status down “ stup ” “ stdn ” ➥ push to select a status message. ➥ when the automatic scroll function is activated, push to cancel it, if desired. ➥ when an sdm that includes...

  • Page 6: Biis 1200 Operation

    3 2 biis 1200 operation ■ biis 1200 operation the binary interchange of information and signalling (biis) 1200 standard is the best choice to add a data service to an existing system. It enables digital communications, signalling and message exchanges with analog transceivers. The biis system provid...

  • Page 7

    4 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d receiving a group call q when a group call is received: • rings sound. • “ ” appears and the mute is released. • “ ” appears or blinks, depending on the pre-programmed set- tings. • the group id (or name) and the calling station’s id (...

  • Page 8

    5 2 biis 1200 operation ■ receiving a call (continued) d receiving a status message q when a status message is received: • rings sound. • the calling station’s id (or name) and the status message blink. W push [moni (audi)] to return to the stand-by mode. Note: when the display mode is one line if t...

  • Page 9

    6 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d displaying a received call record — queue channel mode the transceiver memorizes up to three calling station’s ids. When the fourth call is received, the oldest call record will be removed, and the last received call will be added. Whe...

  • Page 10: Transmitting A Call

    7 2 biis 1200 operation ■ transmitting a call d general • editing an id if the transceiver has a key assigned to the tx code enter function, you can edit an id within the allowable digits. Q push [tx code enter] to enter the id edit mode. • the digit to be edited blinks. W push [tx code enter] to se...

  • Page 11

    8 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a status message you can send a pre-programmed status message to an indi - vidual station or to group stations. There are 24 status messages that can be sent, and status 22 and 24 messages have designated meanings. Status ...

  • Page 12

    9 2 biis 1200 operation ■ transmitting a call (continued) d transmitting an sdm you can send a pre-programmed sdm to an individual station or to group stations. The transceiver has eight memories to store messages. Q push [biis button] to enter the call code memory mode. • “ ” appears. • the pre-pro...

  • Page 13

    10 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 • usable characters note: messages can be edited also using a pc editing program. Ask your dealer for details. D transmitting an emergency call if an msk channel is used as the emergency channel, the transceiver can access the biis emer...

  • Page 14: Position Data Transmission

    11 2 biis 1200 operation ■ position data transmission when a gps receiver is connected to the transceiver, through the opc-966 interface cable ,* the position data (longitude and latitude) can be automatically transmitted. Ask your dealer or system operator for connection details. * this cable is no...

  • Page 15: Printer Connection

    12 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ printer connection when a printer is connected to the transceiver, through the opc-966 interface cable , received sdm and the calling station’s id can be printed out, depending on the pre-pro- grammed settings. Ask your dealer or syst...

  • Page 16: Dpmr Operation

    ■ dpmr operation the ic-f3162dt/ic-f3162ds and ic-f4162dt/ic-f4162ds provide digital private mobile radio (dpmr) operation that meets the 6.25 khz bandwidth requirements for narrow band operation. This increases the efficiency of channel allocation and use of the spectrum. Note: during dpmr operatio...

  • Page 17

    14 3 dpmr operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d receiving a group call q when a group call is received: • rings sound. • “ ” appears and the mute is released. • “ ” appears or blinks, depending on the pre-programmed set- tings. • the talkgroup id (or name) and the calling station’s id (...

  • Page 18

    15 3 dpmr operation ■ receiving a call (continued) d receiving an sdm q when an sdm is received: • rings sound. • the calling station’s id (or name) and the sdm are displayed. Note: when the sdm includes more than 12 charac- ters, it automatically scrolls. • push [status up] or [status down] to stop...

  • Page 19

    16 3 dpmr operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d receiving an ambience listening call if an individual call with an ambience listening command is received from a specified station, the transceiver will auto- matically transmit its microphone audio. Note: if the transceiver receives an am...

  • Page 20

    17 3 dpmr operation ■ receiving a call (continued) d displaying a received call log entry depending on the pre-programmed setting, the transceiver stores up to 10 call log entries. Individual voice, status and sdm call log entries are stored. When an 11th call is re- ceived, the oldest call log entr...

  • Page 21: Transmitting A Call

    18 3 dpmr operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ transmitting a call dpmr operation allows you to make a call to a specific sta- tion (individual call) or to a particular group (talkgroup call). Other digital mode transceivers on the channel will not re- ceive a call that does not match ...

  • Page 22

    19 3 dpmr operation ■ transmitting a call (continued) d transmitting a voice call note: if you want to make a call to the pre-programmed id, skip step q and w and directly go to step e . Q push [dpmr button] to enter the id selection mode. • the pre-programmed id is displayed. W push [ch up] or [ch ...

  • Page 23

    20 3 dpmr operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a status message you can send a pre-programmed status message to an indi - vidual station or to group stations. There are 32 status messages that can be sent. Q push [dpmr button] to enter the id selection mode. • the pre-prog...

  • Page 24

    21 3 dpmr operation ■ transmitting a call (continued) d transmitting an sdm you can send a pre-programmed sdm to an individual station or to group stations. The transceiver has 10 memories to store messages. Q push [dpmr button] to enter the id selection mode. • the pre-programmed id is displayed. W...

  • Page 25

    22 3 3 dpmr operation 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 22 3 d direct message input (only 10-key version) while displaying an sdm, you can edit or change the mes- sage. Q push [dpmr button] twice to enter the application selec- tion mode. • “ status” is displayed. W push [ch up] or [ch down] to s...

  • Page 26

    ■ transmitting a call (continued) d transmitting an emergency call if a digital channel is used as the emergency channel, the transceiver can access the dpmr emergency mode. If your transceiver is programmed for silent operation, you can transmit emergency calls without the beep sounding or the disp...

  • Page 27: Transmitting A Command

    24 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 dpmr operation 24 ■ transmitting a command the following individual calls allow you to send special com- mands. These calls will function if you are designated as a specific station. Ask your dealer for details. D transmitting an ambience listening call an...

  • Page 28

    ■ transmitting a command (continued) d transmitting a kill call a kill call allows you to send a command that will disable the target station. Q push [dpmr button] to enter the id selection mode. • the pre-programmed id is displayed. W push [ch up] or [ch down] to select a desired individual id. E p...

  • Page 29: Position Data Transmission

    26 3 dpmr operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ position data transmission when a gps receiver is connected to the transceiver, through the opc-966 interface cable ,* the position data (longitude and latitude) can be automatically transmitted. Ask your dealer or system operator for conn...

  • Page 30: Printer Connection

    27 3 dpmr operation ■ printer connection when a printer is connected to the transceiver, through the opc-966 interface cable , received sdm and the calling station’s id can be printed out, depending on the pre-pro- grammed settings. Ask your dealer or system operator for connection and set- ting det...

  • Page 31

    Memo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16.

  • Page 32

    1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a-6842-2eu © 2010 icom inc..