1. DL manuals
  2. Icom
  3. Transceiver
  4. IC-M505
  5. Instruction Manual

Icom IC-M505 Instruction Manual

Manual is about: VHF Marine Transceiver

Summary of IC-M505

  • Page 1

    Instruction manual im505 vhf marine transceiver.

  • Page 2: D Features

    I foreword thank you for purchasing this icom product. The ic-m505 vhf marine transceiver is designed and built with icom’s state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble- free operation. We want to take a couple of moments of y...

  • Page 3

    Ii in case of emergency if your vessel requires assistance, contact other vessels and the coast guard by sending a distress call on channel 16. Or, transmit your distress call using digital selective calling on channel 70. Installation note the installation of this equipment should be made in such a...

  • Page 4: 0560

    Iii doc ce versions of the ic-m505 which display the “ce” symbol on the serial number seal, comply with the essential requirements of the euro- pean radio and telecommunication terminal directive 1999/5/ec. This warning symbol indicates that this equip- ment operates in non-harmonised frequency band...

  • Page 5

    Iv foreword …………………………………………………………… i important …………………………………………………………… i explicit definitions ……………………………………………… i in case of emergency…………………………………………… ii installation note ………………………………………………… ii doc …………………………………………………………………… iii table of contents ……………………………………………… iv precautions ………………………………………...

  • Page 6

    V precautions rwarning! Never connect the transceiver to an ac outlet. This may pose a fire hazard or result in an electric shock. Never connect the transceiver to a power source of more than 16 v dc or use reverse polarity. This will ruin the trans- ceiver. Never cut the dc power cable between the ...

  • Page 7: Operating Rules

    1 1 operating rules d d priorities • read all rules and regulations pertaining to priorities and keep an up-to-date copy handy. Safety and distress calls take priority over all others. • you must monitor channel 16 when you are not operating on another channel. • false or fraudulent distress signals...

  • Page 8: Panel Description

    2 panel description 2 ■ front panel q distress key [distress] push for 5 sec. To transmit a distress call. (p. 23) w dsc menu key [menu] push to toggle the dsc menu appear or disappear. (p. 15) e clear key [clr] push to cancel the entered function, exit set mode. (pgs. 9, 10, 55) r hail/rx speaker k...

  • Page 9

    3 2 panel description u channel selector [channel•enter] ➥ rotate to select the operating channels, set mode set- tings, etc. (pgs. 6–8, 55) ➥ while pushing and holding [h/l], rotate to adjust the brightness of the lcd and key backlight. (p. 10) ➥ push to enter the input channel comment, selected it...

  • Page 10: ■ Function Display

    4 2 panel description ■ function display q rx speaker indicator (p. 51) appears during the rx speaker mode. W power indicator (p. 8) ➥ “2 25 5w w” appears when high power is selected. ➥ “1 1w w” appears when low power is selected. E tag channel indicator (p. 13) appears when a tag channel is selecte...

  • Page 11: ■ Microphone

    5 2 panel description 2 !1 position indicator ➥ shows the gps position data. • “? ?? ?” may blink every 2 sec. Instead of position data when the gps position data is invalid. In such a case, the last position data is held for up to 23.5 hours. • “? ?? ?” may blink every 2 sec. Instead of position da...

  • Page 12: Basic Operation

    6 basic operation 3 ■ channel selection ï ï channel 16 channel 16 is the distress and safety channel. It is used for establishing initial contact with a station and for emergency communications. Channel 16 is monitored during both dual- watch and tri-watch. While standing by, you must monitor channe...

  • Page 13

    7 3 basic operation 3 ï ï international channels there are pre-programmed 57 international channels for the ic-m505. Q push [dial•dual/grp] to select a regular channel. W while pushing and holding [h/l], push [dial•dual/grp] to change the channel group, if necessary. • “i in nt t” appears when inter...

  • Page 14

    8 3 basic operation ■ receiving and transmitting caution: transmitting without an antenna may dam- age the transceiver. Q push [power] to turn power on. W set the audio and squelch levels. ➥ rotate [sql] fully counterclockwise in advance. ➥ rotate [vol] to adjust the audio output level. ➥ rotate [sq...

  • Page 15

    9 3 basic operation 3 ■ call channel programming you can program the call channel with your most often-used channels in each channel group for quick recall. Q while pushing and holding [h/l], push [dial•dual• grp] one or more times to select the desired channel group (int, usa, atis or dsc) to be pr...

  • Page 16: ■ Channel Comments

    10 3 basic operation ■ channel comments memory channels can be labelled with a unique alphanumeric id of up to 10 characters. Capital letters, small letters, 0 to 9, some symbols (/ . –) and space can be used. Q select the desired channel. • cancel dualwatch, tri-watch or scan in advance. W while pu...

  • Page 17

    11 3 basic operation 3 ■ optional voice scrambler operation d d activating the scrambler the optional voice scrambler provides private communica- tions. In order to receive or send scrambled transmissions you must first activate the scrambler function. To activate the function, an optional scrambler...

  • Page 18: Scan Operation

    12 scan operation 4 ■ scan types scanning is an efficient way to locate signals quickly over a wide frequency range. The transceiver has priority scan and normal scan. Set the tag channels (scanned channel) before scanning. Clear the tag channels which inconveniently stop scanning, such as those for...

  • Page 19: ■ Setting Tag Channels

    13 4 scan operation 4 ■ setting tag channels for more efficient scanning, add the desired channels as tag channels or clear the tag for unwanted channels. Channels that are not tagged will be skipped during scanning. Tag channels can be assigned to each channel group (int, usa, atis or dsc) independ...

  • Page 20: Dualwatch/tri-Watch

    14 dualwatch/tri-watch 5 ■ description dualwatch monitors channel 16 while you are receiving on another channel; tri-watch monitors channel 16 and the call channel while receiving another channel. Dualwatch/tri- watch is convenient for monitoring channel 16 when you are operating on another channel....

  • Page 21: Dsc Operation

    15 6 dsc operation 5 6 ■ mmsi code programming the 9-digit mmsi (maritime mobile service identity: dsc self id) code can be programmed at power on. This code programming can be performed only once. After the code programming, it can be changed only by your dealer or distributor. Q turn power off. W ...

  • Page 22: ■ Mmsi Code Check

    16 6 dsc operation ■ mmsi code check the 9-digit mmsi (dsc self id) code can be checked. Q push [menu] to enter the dsc menu. W rotate [channel] to select “s se et t u up p,” push [chan- nel•enter]. E rotate [channel] to select “m mm ms si i c ch he ec ck k,” push [channel•enter]. R check the 9-digi...

  • Page 23: ■ Dsc Address Id

    17 6 dsc operation 6 ■ dsc address id a total of 100 dsc address ids can be programmed and named with up to 10 characters. D d programming individual id q push [menu] to enter the dsc menu. W rotate [channel] to select “s se et t u up p,” push [chan- nel•enter]. E rotate [channel] to select “a ad dd...

  • Page 24

    18 6 dsc operation d d deleting individual id q push [menu] to enter the dsc menu. W rotate [channel] to select “s se et t u up p,” push [chan- nel•enter]. E rotate [channel] to select “d de el l: :i in nd dv v i id d,” push [channel•enter]. • when no address id is programmed, “n no o i id d” is dis...

  • Page 25

    19 6 dsc operation 6 d d programming group id q push [menu] to enter the dsc menu. W rotate [channel] to select “s se et t u up p,” push [chan- nel•enter]. E rotate [channel] to select “a ad dd d: :g gr ro ou up p i id d,” push [channel•enter]. R rotate [channel] to set the group id and id name. • t...

  • Page 26

    20 6 dsc operation d d deleting group id q push [menu] to enter the dsc menu. W rotate [channel] to select “s se et t u up p,” push [chan- nel•enter]. E rotate [channel] to select “d de el l: :g gr ro ou up p i id d,” push [channel•enter]. • when no address id is programmed, “n no o i id d” is displ...

  • Page 27

    21 6 dsc operation 6 ■ position and time programming a distress call should include the ship’s position and time data. If no gps is connected, your position and utc (univer- sal time coordinated) time should be input manually. They are included automatically when a gps receiver (nmea0183 ver. 2.0 or...

  • Page 28

    ■ position and time indication when a gps receiver (nmea0183 ver. 2.0 or 3.01) is con- nected, the transceiver displays the current position and time. When no gps receiver is connected, the transceiver displays the manually entered position and time. A gps receiver appropriate for the ic-m505 is not...

  • Page 29: ■ Distress Call

    23 6 dsc operation 6 ■ distress call a distress call should be transmitted, if in the opinion of the master, the ship or a person is in distress and requires imme- diate assistance. Never use the distress call when your ship or a person is not in an emergency. A distress call can be used only when i...

  • Page 30

    24 6 dsc operation ➥ a distress alert contains (default); • nature of distress : undesignated distress • position data : gps or manual input position data held for 23.5 hrs or until the power is turned off. ➥ the distress call is repeated every 3.5–4.5 min., until re- ceiving an ‘acknowledgement.’ ➥...

  • Page 31

    25 6 dsc operation 6 when a gps receiver (nmea0183 ver. 2.0 or 3.01) is con- nected, go to step y. Because the following steps (r and t; current position/time programming) do not appear. R the position information appears. Set your position (lati- tude and longitude) data by rotating [channel]. • pu...

  • Page 32: ■ Transmitting Dsc Calls

    26 6 dsc operation i after receiving the acknowledgment, reply using the mi- crophone. ➥ a distress alert contains (default); • nature of distress : selected nature of the distress • position data : gps or manual input position data is held for 23.5 hrs or until the power is turned off. ➥ the distre...

  • Page 33

    27 6 dsc operation 6 e rotate [channel] to select the desired pre-programmed individual address or “m ma an nu ua al l i in np pu ut t,” push [chan- nel•enter]. • the id code for the individual call can be set in advance. (p. 17) • when “m ma an nu ua al l i in np pu ut t” is selected, set the 9-dig...

  • Page 34

    28 6 dsc operation y standby on channel 70 until an acknowledgement is re- ceived. U when the acknowledgement ‘able to comply’ is received, the specified channel (in step r) is selected with beeps automatically. Or, when the acknowledgement ‘unable to comply’ is received, the display returns to the ...

  • Page 35

    29 6 dsc operation 6 r rotate [channel] to select “a ab bl le e t to o c co om mp pl ly y” or “u un na ab bl le e t to o c co om mp pl ly y,” push [channel•enter]. • when “u un na ab bl le e t to o c co om mp pl ly y” is selected, “no reason given” will be transmitted. T push [channel•enter] to tran...

  • Page 36

    30 6 dsc operation r rotate [channel] to select a desired intership channel, push [channel•enter]. • intership channels are already preset into the transceiver in rec- ommended order. T push [channel•enter] to transmit the group call. • if channel 70 is busy, the transceiver stands by until the chan...

  • Page 37

    31 6 dsc operation 6 d d transmitting an all ships call large ships use channel 70 as their ‘listening channel.’ when you want to announce a message to all ships within range, use the all ships call function. Q push [menu] to enter the dsc menu. W rotate [channel] to select “a al ll l s sh hi ip ps ...

  • Page 38

    32 6 dsc operation t after the all ships call has been transmitted, the following indication is displayed. Y push [clr] to exit and the transceiver selects channel 16 automatically. • even if [clr] hasn’t been pushed, the transceiver automatically selects channel 16 after 2 sec. Of inactivity. D d t...

  • Page 39

    33 6 dsc operation 6 r push [channel•enter] to transmit the position request call. • if channel 70 is busy, the transceiver stands by until the channel becomes clear. T after the position request call has been transmitted, the fol- lowing indication is displayed. Y push [clr] to return to the previo...

  • Page 40

    34 6 dsc operation d d transmitting a position report call transmit a position report call when you want to announce your own position to a specific ship and to get an answer, etc. Q push [menu] to enter the dsc menu. W rotate [channel] to select “p po os si it ti io on n r re ep po or rt t,” push [...

  • Page 41

    35 6 dsc operation 6 y push [channel•enter] to transmit the position report call. • if channel 70 is busy, the transceiver stands by until the channel becomes clear. U after the position report call has been transmitted, the fol- lowing indication is displayed. I push [clr] to return to the previous...

  • Page 42

    36 6 dsc operation d d transmitting a polling request call transmit a polling request call when you want to know if a specific vessel is within communication range. Q push [menu] to enter the dsc menu. W rotate [channel] to select “p po ol ll li in ng g r re eq qu ue es st t,” push [channel•enter]. ...

  • Page 43

    37 6 dsc operation 6 t after the polling request call has been transmitted, the fol- lowing indication is displayed. Y push [clr] to return to the previous indication before en- tering the dsc menu. • even if [clr] hasn’t been pushed, the display automatically re- turns to the previous indication af...

  • Page 44

    38 6 dsc operation when a gps receiver (nmea0183 ver. 2.0 or 3.01) is con- nected, go to step y. Because the following steps (r and t; current position/time programming) do not appear. R the position information appears. Set your position (lati- tude and longitude) data by rotating [channel]. • push...

  • Page 45

    39 6 dsc operation 6 d d transmitting a position report reply call transmit a position report reply call when a position report call is received. Q push [menu] to enter the dsc menu. W rotate [channel] to select “p po os s r re ep po or rt t r re ep pl ly y,” push [channel•enter]. • “p po os s r re ...

  • Page 46

    40 6 dsc operation d d transmitting a polling request reply call transmit a polling reply call when a polling request call is re- ceived. Q push [menu] to enter the dsc menu. W rotate [channel] to select “p po ol ll li in ng g r re ep pl ly y,” push [channel•enter]. • “p po ol ll li in ng g r re ep ...

  • Page 47: ■ Receiving Dsc Calls

    41 6 dsc operation 6 ■ receiving dsc calls d d receiving a distress call while monitoring channel 70 and a distress call is received: ➥ the emergency alarm sounds for 2 minutes. • push [clr] to stop the alarm. ➥ “r re ec ce ei iv ve ed d d di is st tr re es ss s” appears in the display, then channel...

  • Page 48

    42 6 dsc operation d d receiving an individual call while monitoring channel 70 and an individual call is re- ceived: ➥ the emergency alarm or beeps sound depending on the received category. ➥ “r re ec ce ei iv ve ed d i in nd di iv vi id du ua al l” appears in the display. ➥ push [clr] to stop the ...

  • Page 49

    43 6 dsc operation 6 d d receiving a geographical area call while monitoring channel 70 and a geographical area call (for the area you are in) is received: ➥ emergency alarm or beeps sound depending on the re- ceived category. ➥ “r re ec ce ei iv ve ed d g ge eo og gr ra ap ph hi ic c” appears in th...

  • Page 50

    44 6 dsc operation d d receiving a polling request call while monitoring channel 70 and a polling request call is re- ceived: ➥ “r re ec ce ei iv ve ed d p po ol ll l r re eq q” appears in the display. ➥ push [clr] to stop the beep, then push [channel• enter] to reply to the call; push [clr] to igno...

  • Page 51: ■ Received Messages

    45 6 dsc operation 6 ■ received messages the transceiver automatically stores up to 20 distress mes- sages and 20 other messages. The messages can be used as an assistance to the logbook. Q push [menu] to enter the dsc menu. W rotate [channel] to select “r re ec ce ei iv ve ed d c ca al ll ls s,” pu...

  • Page 52

    46 6 dsc operation d d other messages q rotate [channel] to select “o ot th he er r,” push [chan- nel•enter]. W rotate [channel] to scroll to the desired message, push [channel•enter]. • messages which are blinking have not been read. E rotate [channel] to scroll the message. • the stored message ha...

  • Page 53: ■ Dsc Set Mode

    47 6 dsc operation 6 ■ dsc set mode d d mmsi code check (see p. 16) d d add individual id/group id (see pgs. 17, 19) d d delete individual id/group id (see pgs. 18, 20) d d offset time this item sets the offset time from the utc (universal time coordinated) time. Q push [menu] to enter the dsc menu....

  • Page 54

    48 6 dsc operation d d automatic acknowledgement this item sets the automatic acknowledgement function to on or off. When a position request, position report or polling request call is received, the transceiver automatically transmits a position request reply, position report reply or polling reply ...

  • Page 55

    49 6 dsc operation 6 d d nmea output select an nmea output function from off, all station or list station. When receiving position acknowledgment, the transceiver outputs it to the external equipment via the nmea connector. Q push [menu] to enter the dsc menu. W rotate [channel] to select “s se et t...

  • Page 56: Other Functions

    50 other functions 7 ■ intercom operation the optional intercom function allows you to talk to the deck from the cabin. The optional commandmic iii™ is required for intercom operation. Connect an optional command microphone as described on p. 63. • transmitting is impossible during intercom operatio...

  • Page 57: ■ Rx Speaker Function

    51 7 other functions 7 • while in the intercom mode, the transceiver functions (transmit and receive) are interrupted. If the transceiver is in transmit condition, the intercom function is not avail- able. • when a dsc call is received, the intercom function is in- terrupted with an automatic return...

  • Page 58: ■ Hailer Operation

    52 7 other functions ■ hailer operation the ic-m505 has a hailer function for voice amplification over a loudspeaker, making it unnecessary to leave the bridge to talk a hailing party. Connect an external hailer speaker (25 w nominal at 13.8 v/4 Ω ) as described on p. 58. • transmitting is not possi...

  • Page 59

    53 7 other functions 7 ■ automatic foghorn function the automatic foghorn function sounds a horn repeatedly until the function is turned off. Four patterns are available for varying conditions. The foghorn outputs from the hailer speaker. To use this func- tion, the hailer speaker must be connected ...

  • Page 60

    54 7 other functions q while pushing and holding [h/l], push [hail•rx ] to enter auto foghorn mode. W rotate [channel] to select the desired foghorn pattern, push [channel•enter]. • ‘u un nd de er rw wa ay y,’ ‘s st to op p,’ ‘s sa ai il l,’ ‘t to ow w’ are available. (p. 53) • even if [channel•ente...

  • Page 61: Set Mode

    55 8 set mode 7 8 ■ set mode programming set mode is used to change the conditions of the transceiver’s functions: scan type, scan resume timer, dual/tri-watch, beep tone, lcd contrast, automatic foghorn frequency, radio power, scrambler type* and scrambler code.* *appears only when the optional scr...

  • Page 62

    56 8 set mode d d dual/tri-watch this item can be selected as dualwatch or tri-watch. (p. 14) d d beep tone you can select the silent operation by turning beep tones off or you can have confirmation beeps sound at the push of a key by turning beep tones on. D d lcd contrast the lcd contrast can be a...

  • Page 63

    57 8 set mode 8 d d radio power (appears when the hm-162e is connected) this item sets the radio power function on or off. On : the transceiver’s power is controlled by the optional command microphone. When the command micro- phone is turned off, the transceiver will also be turned off automatically...

  • Page 64: Connections And Maintenance

    58 connections and maintenance 9 ■ connections q nmea in lead (red) connects to a gps receiver for position indication. • a nmea0183 ver. 2.0 or 3.01 (sentence formatters rmc, gga, gns, gll and vtg) compatible gps receiver is required. Ask your dealer about suitable gps receivers. W nmea out lead (w...

  • Page 65: ■ Antenna

    59 9 connections and maintenance 9 caution: after connecting the dc power cable, nmea in/out leads, external speaker lead and hailer/foghorn lead, cover the connector and leads with an adhesive tape as shown below, to prevent water seeping into the transceiver. ■ antenna a key element in the perform...

  • Page 66

    60 9 connections and maintenance ■ mounting the transceiver d d using the supplied mounting bracket the universal mounting bracket supplied with your transceiver allows overhead or dashboard mounting. • mount the transceiver securely with the 4 supplied screws (5 × 20) to a surface which is more tha...

  • Page 67: ■ Mb-75 Installation

    61 9 connections and maintenance 9 ■ mb-75 installation an optional mb-75 flush mount kit is available for mounting the transceiver to a flat surface such as an instru- ment panel. Caution: keep the transceiver and microphone at least 1 meter away from your vessel’s magnetic navigation com- pass. Q ...

  • Page 68

    62 9 connections and maintenance ■ ut-112/ut-98 installation caution: disconnect the dc power cable from the transceiver before performing any work on the transceiver. Otherwise, there is danger of electric shock and/or equip- ment damage. Follow the case opening procedure shown here when you want t...

  • Page 69: ■ Hm-162E Installation

    63 9 connections and maintenance 9 r return the cables and screws to the original position. • be sure not upside down the flat cable. Caution: • when re-assembling the case and tightening the screws, you must keep the specified torque (0.5±0.07 n.M). Oth- erwise the transceiver may be damaged (torqu...

  • Page 70

    64 9 connections and maintenance q insert the supplied cable into the external microphone jack and tighten the cable nut as shown below. W to use the supplied cable as a wall socket, perform the fol- lowing steps. E using the mounting base as a template, carefully mark the holes where the cable and ...

  • Page 71

    65 9 connections and maintenance 9 gasket mounting base cap nut.

  • Page 72: Troubleshooting

    66 troubleshooting 10 possible cause solution ref. No sound from speaker. • squelch level is too high. • volume level is too low. • speaker has been exposed to water. P. 8 p. 8 — • set [sql] to the threshold point. • set [vol] to a suitable level. • drain water from the speaker. The transceiver does...

  • Page 73: Specifications And Options

    67 11 specifications and options 10 11 ■ specifications d d general • frequency coverage : tx 156.000–161.450 mhz rx 156.000–163.425 mhz • mode : fm (16k0g3e), dsc (16k0g2b) • channel spacing : 25 khz • current drain (at 13.8 v) : tx high 5.5 a max. Max. Audio 1.5 a max. • power supply requirement :...

  • Page 74: ■ Options

    68 11 specifications and options d d dimensions ■ options • mb-75 flush mount kit for mounting the transceiver to a panel. • hm-162e commandmic iii ™ external microphone-type controller. Provides optional inter- com operation. 6 m microphone cable and mount-ing base in- cluded. Black and white color...

  • Page 75: Channel List

    69 12 channel list 11 12 • international channels ch frequency (mhz) ch frequency (mhz) ch frequency (mhz) ch frequency (mhz) ch frequency (mhz) ch frequency (mhz) transmit receive transmit receive transmit receive transmit receive transmit receive transmit receive 01 156.050 160.650 11 156.550 156....

  • Page 76

    70 12 channel list • usa channels (for u.K. Version only) frequency (mhz) frequency (mhz) frequency (mhz) frequency (mhz) frequency (mhz) frequency (mhz) transmit receive transmit receive transmit receive transmit receive transmit receive transmit receive 156.050 156.050 156.600 156.600 157.100 157....

  • Page 77: Template

    Template hm-162e unit: mm 29.5 to 31.5 (d) 2 165 11 0 146 92.4 r12 (max.) mb-75 cut here.

  • Page 79

    Memo.

  • Page 80

    1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan at fi it pl gb ro be fr lv pt is tr cy de lt sk li hr cz gr lu si no dk hu mt es ch ee ie nl se bg a-6484h-1eu-e printed in japan © 2006–2007 icom inc. Printed on recycled paper with soy ink..