Instruction manual fish finder mxf-5000 this device complies with part 15 of the fcc rules. Opera- tion is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause unde...
I foreword thank you for purchasing icom’s mxf-5000 fish finder. The fish finder is designed for use with the icom marinecommander™ system through the supplied connection cable. It has powerful transmission power and many other advanced features can be used with the icom marinecommander™ system. Aft...
Supplied accessories connection cable (1.5 m (4.92 ft)) × 1 dc power cable (3 m (9.84 ft)) × 1 bolts (m5×30 mm) × 4 nuts (m5) × 4 flat washers (m5) × 8 spring washers (m5) × 8 spare fuse (fgb 5 a) × 1 (for 12 v power source) fuse (fgb 3 a) × 1 (for 24 v power source) table of contents ii foreword ··...
Iii precautions r danger: a transducer must be installed by a shipbuilder or a qualifi ed installer. Improper installation could cause water leaks and other severe damage. R warning: never let metal, wire or other objects touch any internal part or terminals of the fi sh fi nder. This may result in ...
1 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 q w r this terminal is not used. E q dc power input terminals (p. 3) connect the 12 v/24 v dc power supply through the supplied dc power cable. W ground terminals (p. 3) connect these terminals to ground to prevent electrica...
2 installation and connections 2 ■ jumper setting (when connecting an ex-3195 only) when connecting an ex-3195, move the jumper (main unit; j15) to the 1 kw position as follows. Caution: before changing the jumper setting, make sure disconnecting the fi sh fi nder’s dc power cable from the battery. ...
■ power source requirement caution : before connecting the dc power cable, check the following important items. Make sure: • output voltage of the power source is 12/24 v dc. • dc power cable polarity is correct. Red : positive + terminal black : negative _ terminal • fuse rating of the dc power cab...
4 2 installation and connections ■ mounting first, drill four φ 5.5–6 mm ( 7 ⁄ 32 – 1 ⁄ 4 ″ ) holes to mount the fi sh fi nder using the units base as a pattern. Mount the fish finder securely with the four supplied bolts (m5×30 mm) to a flat surface which supports more than approx. 5 kg (11 lb). Ca...
5 2 installation and connections 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d installation position r danger: a transducer must be installed by a shipbuilder or a qualifi ed installer. Improper installation could cause water leaks and other severe damage. R warning: be sure the fi sh fi n...
6 2 installation and connections d optional transducer’s dimensions (approx.) • ex-3193 (600 w transom type, built-in boat speed and temperature sensors) • ex-3194 (600 w thru hull type, built-in boat speed and temperature sensors) • ex-3195 (1 kw thru hull type, built-in temperature sensor) 70 mm (...
3 7 maintenance and options ■ maintenance and inspection continued, reliable operation of the fish finder depends on how you care for your equipment. The simple maintenance tips that follow can help you save time and money, and avoid premature equip- ment failures. ■ periodic maintenance q keep the ...
4 8 specifications ■ mxf-5000 • power supply : 10.8 v to 31.2 v dc • current drain : less than 0.6 a (water depth range: 40 m/output power: 600 w at 12 v dc) less than 1.0 a (water depth range: 40 m/output power: 1 kw at 12 v dc) • output power : 600 w/1 kw • transmission frequency : 50 khz ±1 khz 2...
9 memo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21.
10 memo.
11 memo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21.
1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a-6753h-1ex- q printed in japan © 2009 icom inc..
