Icom MR-1200RII Instruction Manual - page 9
4
1
PANEL DESCRIPTION
#5
COMPASS/GYRO INDICATOR
(pp. 28, 43)
• GYRO:
NMEA (gyro) is connected.
• COMPASS: NMEA (compass), N+1 or AUX data is
connected.
#6
EBL1/ 2 READOUTS
(pp. 15, 16)
Shows the bearing of the displayed Electronic Bear-
ing Lines (EBL1 and EBL2) when EBL is in use.
#7
WAYPOINT/MOB READOUTS
(p. 13)
➥
Shows the bearing and distance to the waypoint
received from navigation equipment.
• This readout appears when “WPT” in the FUNCTION
menu is turned ON.
• To display the waypoint/MOB marker, bearing data
and NMEA data in 0183 format is necessary. (p. 43)
➥
Shows the bearing and distance to the MOB
(Man Over Board) event marker.
• Push [MOB]/[
] to cancel the readout and the
symbol.
#8
POSITION/CURSOR READOUT
(p. 13)
Shows your own ship or cursor latitude and longi-
tude readout when external NMEA data in 0183 for-
mat is connected.
• Select ‘SHIP’ or ‘CURS’ in the “POSN DISP” item of the
FUNCTION menu.
• To display the POSITION, NMEA 0183 is necessary.
• To display the CURSOR, NMEA 0183 and bearing data
are necessary.
#9
TUNING LEVEL INDICATOR
(p. 9)
Shows the receiver tuning level.
$0
CURSOR INDICATOR
Shows the bearing and distance to the cursor.
• R: Relative bearing, T: True Bearing, M: Magnetic bearing
$1
VECTOR INDICATOR
(p. 19)
Shows the ATA, AIS and OWN vector type.
• T: True vector, R: Relative vector
$2
VECTOR TIME INDICATOR
(p. 19)
Shows the vector time. Select vector time in “VECT
TIME” of the TARGET menu.
$3
TRAILS INDICATOR
(p. 12)
Shows the trail time.
• The echo remains, with gradation, during the trail time
period on the screen. (Except for the trail time;
∞
)
• Progressing time counter starts counting until the timer
reaches the trail time.
$4
HEADING INDICATOR
Shows the heading bearing readout.
• HDG: When “BRG INPUT” in the INT. SETTING menu is
selected “NMEA,” “N+1” or “AUX.”
• COG: When “BRG INPUT” in the INT. SETTING menu is
selected “GPS.”
• The HDG readout indicates the bow of the ship’s bear
-
ing in a clockwise direction from north.
• R: Relative bearing, T: True Bearing, M: Magnetic bearing
$5
IR INDICATOR
(p. 11)
Eliminates or reduces interference caused by other
radar operating nearby.
• This indicator appears when “IR” in the VIDEO menu is
set to 1 or 2.
$6
ECHO STRETCH INDICATOR
(p. 11)
Appears when the echo stretch function is in use.
• This indicator appears when “STRETCH” in the VIDEO
menu is turned ON.
$7
CROSS LINE CURSOR
Used to measure the bearing and distance, setting
the alarm zone, selecting the ATA/AIS targets, and
so on.
• Push [
p
], [
q
], [
t
] or [
u
] one or more times to move
the cursor.
$8
OWN SHIP VECTOR INDICATOR
Shows the vector of your own ship.
$9
VRM 1
(pp. 15, 16)
%0
VRM 2
(pp. 15, 16)
Used to measure distance. When a target is se-
lected, the VRM1/2 readout (
%4
) shows its dis-
tance.
%1
NORTH MARK
The north mark shows the true north direction.
%2
EBL1
(pp. 15, 16)
%3
EBL2
(pp. 15, 16)
Used to measure bearing. When a target is se-
lected, the EBL readout (
#6
) shows its bearing.
%4
VRM1/2 READOUTS
(pp. 15, 16)
Shows the distance of the displayed Variable Range
Markers (VRM1 and VRM2) when the VRM is in
use.
• Nautical miles (NM) or kilometers (KM) can be selected
in the FUNCTION menu as the distance unit.
%5
ALARM INDICATOR
(p. 17)
Appears when the alarm function is in use.
%6
ZOOM INDICATOR
(p. 11)
Appears when the zoom function is in use.
• Push [TARGET]/[
] and [TRAILS]/[
] simul-
taneously to turn the function ON or OFF.
%7
TIME INDICATOR
%8
TIME INDICATOR
Shows the estimated time to the marker edge from
the center of the marker, at the current speed.
%9
TIME INDICATOR
Shows the estimated time to the waypoint at the
current speed.