ICON Health & Fitness Pro-Form PFEVEX39832 User Manual - page 9
9
16
HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 15.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
audio cable into the adapter. Plug the adapter into
the AUDIO OUT jack on your VCR.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
audio cable into the adapter. Plug the adapter into
an RCA Y-adaptor (available at electronics stores).
Next, remove the wire that is currently plugged into
the AUDIO OUT jack on your VCR and plug the
wire into the unused side of the Y-adaptor. Plug the
Y-adaptor into the AUDIO OUT jack on your VCR.
AUDIO OUT
RIGHT
LEFT
VIDEO AUDIO
ANT. IN
RF OUT
IN
OUT
CH
3
4
C
Audio Cable
Adapter
A
VIDEO AUDIO
ANT. IN
RF OUT
IN
OUT
CH
3
4
A
Audio Cable
Adapter
B
Wire removed from
AUDIO OUT jack
RCA
Y-adaptor
HOW TO OPERATE THE EXERCISE CYCLE
HOW TO ADJUST THE SEAT POST
For effective exer-
cise, the seat
should be at the
proper height. As
you pedal, there
should be a slight
bend in your knees
when the pedals
are in the lowest
position. To adjust
the height of the
seat, first turn the
indicated knob
counterclockwise two or three turns to loosen it (if the
knob is not loosened enough, it may scratch the seat
post). Next, pull the knob, slide the seat post to the
desired height, and then release the knob.
Move the
seat post up and down slightly until the pin on the
knob snaps into one of the holes in the seat post.
Then, turn the knob clockwise until it is tight.
HOW TO ADJUST THE SEAT
The seat can be
adjusted to the
position that is the
most comfortable
for you.
Before
adjusting the seat,
dismount the
exercise cycle; do
not adjust the
seat while you are
sitting on it. To
adjust the seat, first
turn the indicated knob counterclockwise two or three
turns to loosen it (if the knob is not loosened enough, it
may scratch the seat bracket). Next, pull the knob,
slide the seat to the desired position, and then release
the knob.
Move the seat bracket forward and back-
ward slightly until the pin on the knob snaps into
one of the holes in the seat bracket. Then, turn the
knob clockwise until it is tight.
HOW TO ADJUST THE HANDLEBAR
The handlebar can
be adjusted to the
position that is the
most comfortable for
you. To adjust the
handlebar, first turn
the indicated handle
counterclockwise to
loosen it. Note: The
adjustment handle
works like a span-
ner. Turn the handle
counterclockwise,
pull it away from the handlebar, turn it clockwise, push
it toward the handlebar, and then turn it counterclock-
wise again. Repeat this procedure until the handlebar
is loose. Move the handlebar up or down to the desired
position, and then turn the handle clockwise until it is
tight.
HOW TO ADJUST THE PEDAL STRAPS
See assembly step 9 on page 8 to adjust the pedal
straps.
HOW TO LEVEL THE EXERCISE CYCLE
If the exercise cycle
does not sit flat on
the floor, turn one or
both of the leveling
pads until the exer-
cise cycle is level.
Seat
Post
Knob
Seat
Seat
Bracket
Seat
Knob
Handle
Pads