1. DL manuals
  2. ICON
  3. Fitness Equipment
  4. weider 8515 WESY87150
  5. User Manual

ICON weider 8515 WESY87150 User Manual

Summary of weider 8515 WESY87150

  • Page 1

    User's manual questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete sat- isfaction through our customer service department. Please call: 0345-089009 or write...

  • Page 2

    2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3

    3 1. It is the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 3. Use the home gym system only on a level surface. Cove...

  • Page 4

    4 before you begin assembled dimensions: height: 74 in. Width: 40 in. Length: 53 in. Foot plate low pulley station high pulley station lat bar seat leg lever butterfly arms press arm weight stack weight pin backrest stepper pedals resistance cylinders thank you for selecting the versatile weider ¨ 8...

  • Page 5

    5 assembly 1 56 high side of bracket handles 3 5 51 long side 31 51 14 1 1 27 4 before beginning assembly, carefully read the following information and instructions: ¥ place all parts of the weider 8515 in a cleared area and remove the packing materials; do not dispose of the packing materials until...

  • Page 6

    6 frame assembl y 2. Slide the front upright (42) onto the 5/16Ó x 2 1/2Ó carriage bolts (1) in the base (4). Hand tighten a 5/16Ó nylon locknut (3) onto each carriage bolt. Do not tighten the nylon locknuts yet. Press a 1Ó square inner cap (65) into the front upright (42). Attach the slotted end of...

  • Page 7

    5. Lubricate the pedal axles on the rear upright (56). Slide the left pedal (79) onto the left pedal axle, and the right pedal (78) onto the right pedal axle. Note: make sure that the pedals are on the correct sides; the slot- ted brackets must be on the insides of the pedals. Hold a 1" retainer (69...

  • Page 8

    8 frame assembl y arm assembl y 9. Press the weight tube bumper (64) into the end of the weight tube (63). Insert the weight tube into the stack of weights (25). Be sure that the pins on the weight tube are sitting in the pin grooves in the top weight. Lubricate the insides of the holes in the top w...

  • Page 9

    9 arm assembl y 12. Wet the handle of one press arm (46) with soapy water. Slide a 5Ó plastic grip (31) onto the handle. Press a 1Ó round inner cap (49) into the other end of the handle. Press a 1 3/4Ó square inner cap (44) into the top of the press arm (46). Attach the press arm (46) to one side of...

  • Page 10

    10 cable assembl y as you assemble the cables and pulleys in steps 14 through 22, please refer to the cable diagram on page 22 of this manual. 14. Route the long cable (23) around the 3 1/2Ó pulley (15) attached to the top frame (55). Be sure that the end of the cable with the ball is on the indicat...

  • Page 11

    14 cable assembl y 22. Attach the long cable (23) to the small ÒuÓ- bracket (67) with a 1/4Ó nylon locknut (2) and a 1/4Ó flat washer (10). Do not com- pletely tighten the nylon locknut. It should be threaded onto the end of the cable so only a couple of threads are showing above the nylon locknut, ...

  • Page 12

    Cable assembl y 12 3 6 9 58 15 21 66 92 9 17 20 21 2 2 10 58 67 10 57 58 20. Route the short cable (58) around the 3 1/2Ó pulley (15) attached to the upper hole in the press frame (17). Be sure that the cable trap (66) is in the Ò3 oÕclockÓ position and that the cable is routed around the pulley as ...

  • Page 13

    Important: the assembly is divided into four stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly, and 4) seat and backrest assembly. The hardware for each stage is packaged separately. Wait until you begin each assembly stage to open that parts bag. This char...

  • Page 14

    5/16" nylon locknut (3)Ð19 1/4" flat washer (10)Ð6 5/16" flat washer (8)Ð6 1" retainer (69)Ð6 1/4" x 2 1/2" screw (43)Ð2 5/16" x 1 3/4" bolt (72)Ð1 1/4" x 2" machine screw (24)Ð1 5/16" x 2" eyebolt (35)Ñ1 5/16" x 2 1/2" carriage bolt (1)Ð3 5/16" x 2 3/4" carriage bolt (14)Ð3 1/4" x 1/2" screw (18)Ð2...

  • Page 15

    Remove this part list/exploded drawing from the manual! 81 note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover for information about ordering replacement parts. Key no. Qty. Description 1 3 5/16Ó x 2 1/2Ó carriage bolt 2 3 1/4Ó nylon lo...

  • Page 16

    23 11 11 8 8 55 27 12 15 44 15 71 23 21 44 21 3 61 60 3 3 5 51 14 19 26 51 25 64 63 3 76 72 9 92 3 3 4 1 27 65 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 69 70 47 48 44 45 44 45 52 53 39 49 62 2 10 67 54 31 31 74 12 68 55 3 21 66 15 20 74 31 49 46 31 46 22 3 9 16 15 21 58 59 17 21 44 44 66 73 71 49 13 ...

  • Page 17

    23 11 11 8 8 55 27 12 15 44 15 71 23 21 44 21 3 61 60 3 3 5 51 14 19 26 51 25 64 63 3 76 72 9 92 3 3 4 1 27 65 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 48 44 45 52 53 39 49 62 2 10 67 12 68 55 3 21 66 15 20 74 83 84 85 7 81 56 31 1 3 3 8 11 87 89 15 89 71 90 91.