1. DL manuals
  2. Interchange
  3. Nail Gun
  4. NF6515-34
  5. Operator's Manual

Interchange NF6515-34 Operator's Manual

Summary of NF6515-34

  • Page 1

    Operator’s manual note: please read and fully understand the instructions in this manual before operating the pneumatic power tool. Carefully read through this operator’s manual to ensure efficient, safe operation. It is recommended that the manual be kept readily available as an important refer- en...

  • Page 2: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 2 interchange brands operator’s manual index information . . . . . . . . . . . . . . . . . . . . . . . . . . . Page important information . . . . . . . . . . . . . . . . . . . . . ....

  • Page 3: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 3 interchange brands operator’s manual important information warning: the warnings, cautions and instructions discussed in this instruction manual can not cover all possible conditi...

  • Page 4: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 4 interchange brands operator’s manual tool information nailer specifications: nf6515-34 15 ga. Finish nailer tool dimensions - length x height x width 13-17/32" x 11-31/32" x 3-7/3...

  • Page 5: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 5 interchange brands operator’s manual parts identification exhaust accessories standard accessories 1 eye protection 1 ①.

  • Page 6: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 6 interchange brands operator’s manual safety information important safety instructions for operating nailers read all instructions 1. Operators and others in work area must wear sa...

  • Page 7: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 7 interchange brands operator’s manual 10. Stay alert. Watch what you are doing . Use common sense and do not operate the nailer when you are tired . The nailer should never be used...

  • Page 8: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 8 interchange brands operator’s manual 22. Keep all screws and covers mounted tightly in place. Keep all screws and covers tightly mounted . Check their condition periodically . Nev...

  • Page 9: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 9 interchange brands operator’s manual 32. Disconnect the air supply and empty the magazine when the nailer is not in use. Never leave a nailer unattended with the hose attached. Al...

  • Page 10: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 10 interchange brands operator’s manual operating the nailer note: the information contained in this manual is designed to assist you in the safe operation of the nailer . Some illu...

  • Page 11: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 11 interchange brands operator’s manual warning never connect nailer to pressure which potentially exceeds 150 psi. Do not use the wrong fitting on nailer. The nailer and air hose m...

  • Page 12: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 12 interchange brands operator’s manual testing the nailer 1. Disconnect air hose from nailer . Remove all nails from nailer . All screws must be tightened. If any screws are loose,...

  • Page 13: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 13 interchange brands operator’s manual 4. Separate the safety/push lever from the wood . Next, point the nailer downward, pull the trigger and then wait in that position for 5 seco...

  • Page 14: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 14 interchange brands operator’s manual operating the nailer danger: operators and others in work area must wear safety glasses with side shields . Eye protection equipment must con...

  • Page 15: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 15 interchange brands operator’s manual driving depth adjustment dial (on some models) warning: always disconnect air supply before changing the adjustment dial . ■ with air pressur...

  • Page 16: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 16 interchange brands operator’s manual maintenance and inspection read the section titled safety. Note: the information contained in this manual is designed to assist you in the sa...

  • Page 17: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 17 interchange brands operator’s manual parts drawing/schematics for nf6515-34 parts drawing/schematics, parts list & parts kits.

  • Page 18: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 18 interchange brands operator’s manual parts list for nf6515-34 no. Order no. Description no. Order no. Description 1 610170 bolt m6x12 (loctite 243) 39 630120 steel ball 2 321080 ...

  • Page 19: 15 Ga. Angled Finish Nailer

    15 ga. Angled finish nailer drives 34˚ finish nails (1-1/4" to 2-1/2" / 32 to 65mm) model no. Nf6515-34 item no. 65420 19 interchange brands operator’s manual parts kits for nf6515-34 order no. Desc. Code kit # item 98580 nf6515k1 kit #1 o-ring/gasket kit for nf6515-34 98585 nf6515k2 kit #2 piston/d...

  • Page 20

    Nf6515-34 15 ga. Finish nailer made in china db limited five (5) year warranty for pneumatic nailers our products are designed and constructed using the highest standards of both mate- rial and workmanship. We warrant to the original retail purchaser that their nailers will be free from defects in m...