1. DL manuals
  2. Intermec
  3. PDA
  4. 6640
  5. Installation Instructions Manual

Intermec 6640 Installation Instructions Manual - Introduction

Manual is about: Intermec 6640: Reference Guide

Summary of 6640

  • Page 1

    Installation instructions p/n 962-040-003 revision a november 1999 6640 dock p/n 962-040-003 revision a *962040003*.

  • Page 2: Introduction

    2 introduction these instructions provide useful information for installing and using the 6640 vehicle and inĆpremise docks. Numerous threaded inserts are provided on both the rear and bottom of these docks to accomodate existing mounting device hole patterns. These deĆ vices can be ordered through ...

  • Page 3: Connectors

    3 connectors 1. Parallel port, lpt1 (25-pin, printer) 2. Com port, rs-232 (9-pin) 3. General purpose i/o port, (15-pin) 4. Dc power input (vehicle dock only) 5. Remote radio antenna jacks 1 2 docks can be configured with various connector combinations. A composite dock is shown below. All possible c...

  • Page 4: Docking Procedures

    4 docking procedures note these four items in the illustrations below: (1) alignment recesses, (2) alignment wedges, (3) gripper, (4) dock latch. Follow these instructions to successfuly dock your 6640 computer: docking : 1. Place alignment recesses (bottom of the computer) onto the wedges (top of d...

  • Page 5: Information

    5 information the following pages contain dimensional information and drawings to help plan mounting locations for the 6640 docks. Engineering drawings are preĆ liminary and may be incomplete. Illustrations found on later pages show hole patterns for various available dock mounting brackets. Pay clo...

  • Page 6

    6.

  • Page 7

    7.

  • Page 8

    8 " a " a 2.293” " a 4.585” y b .750” 1.262” " a 2.659” thru-hole pattern *allows mounting to wall, plywood, or metal bulkhead *8 holes, 0.188” diameter note only the holes for this pattern are shown below..

  • Page 9: Caution

    9 three-hole pattern *1/4-20 threads, 3 holes y b " a 2.063” 1.191” caution maximum screw penetration is 1/4 inch in from outside surface to prevent damage to internal components. Note only the holes for this pattern are shown below..

  • Page 10: Caution

    10 four-hole pattern (see next page) *1/4-20 threads, 4 holes (rear) *#10-32 threads, 2 holes (bottom) caution maximum screw penetration is 1/4 inch in from outside surface to prevent damage to internal components. Y b " a 2.567” 1.283” note only the holes for this pattern are shown below. 4.0”.

  • Page 11: Four-Hole Adapter Bracket

    11 four-hole adapter bracket in the arrangement below, a custom adapter bracket aligns to the fourĆhole pattern on the back of the dock. The two bottom holes should also be used for stability..

  • Page 12: Caution

    12 " a 1.458” y b 1.0” b y 1.0” " a 1.458” six-hole pattern #6-32 threads, 6 holes caution maximum screw penetration is 3/8ths inch in from out- side surface to prevent damage to internal components. Note only the holes for this pattern are shown below..

  • Page 13: Caution

    13 1.372” 1.372” 2.981” c/l 2.981” c/l bottom pattern #6-32 threads, 4 holes caution maximum screw penetration is 3/8ths inch in from out- side surface to prevent damage to internal components. Note use this hole pattern to install the keyboard tray on the front of the dock. The keyboard tray is sho...

  • Page 14: Keyboard Mounting Tray

    14 keyboard mounting tray install the keyboard tray: 1. Remove the front four screws that fasten the bottom plate to the dock. 2. Attach the keyboard tray to the bottom of the dock using those four screws. (use a threadlocker such as loctite surface curing threadlock" #425) 3. Remove the backing pa...