Conser ver installation, operation, and service manual conserver ® xl-e/xl-e-lth/xl hh manual • 07610-003-92-84-q conserver ® xl-e, xl-e-lth, & xl hh dishmachines ®.
Manufacturer's warranty one year limited parts and labor warranty all new jackson dishwashers are warranted to the original purchaser to be free from defects in material or workmanship, under normal use and operation, for a period of (1) one year from date of purchase, but in no event to exceed (18)...
I revision letter revision date made by applicable ecns details a 1-6-14 mhh 8241 release to production. B 8-18-14 kap 8305 removed pg 17, updated part on page 20. C 8-29-14 kap n/a updated part on pg. 27. D 10-14-14 kap n/a added 208 volt schematic on page 32. Updated available electrical character...
Ii the manufacturer provides technical support for all of the dishmachines detailed in this manual. We strongly recommend that you refer to this manual before making a call to our technical support staff. Please have this manual open when you call so that our staff can refer you, if necessary, to th...
Iii guides symbols ......................................................................................................................................1 abbreviations & acronyms ..........................................................................................................1 specificatio...
Iv table of contents maintenance preventative maintenance ........................................................................................................ 22 troubleshooting common problems .........................................................................................................
07610-003-92-84-q 1 guides guides symbols ! Caution ! Warning notice - risk of injury to personnel. - risk of damage to equipment. - risk of electrical shock. - lockout electrical power. - reference data plate. - important note. I - caustic chemicals. Abbreviations & acronyms ansi - american nationa...
07610-003-92-84-q 2 e1 main electrical connection (1 1/8” hole) (located on back of control box) w main inlet water connection (3/4" npt) d drain connection (2” npt) det detergent bulkhead access (7/8” hole) san sanitizer inlet ra rinse-aid inlet 1 (24.63 mm) 13 1/4 (337.18 mm) 29 1/2 (750.28mm) 78 ...
07610-003-92-84-q 3 e1 main electrical connection (1 1/8” hole) (located on back of control box) w main inlet water connection (3/4" npt) d drain connection (2” npt) det detergent bulkhead access (7/8” hole) san sanitizer inlet ra rinse-aid inlet 1 (24.63 mm) 13 1/4 (337.18 mm) 29 1/2 (750.28mm) 78 ...
07610-003-92-84-q 4 conserver xl-e hh 13 in [328 mm] 5 3 4 in [146 mm] 79 1 2 in [2019 mm] doors open 29 1 2 in [748 mm] 76 in [1928 mm] w det san ra 67 3 4 in [1721 mm] 2 1 2 in [63 mm] 9 3 4 in [248 mm] 29 1 4 in [743 mm] e1 6 3 4 in [174 mm] 24 1 2 in [620 mm] 33 1 2 in [853 mm] 31 in [787 mm] 13...
07610-003-92-84-q 5 please remove the front dress panel from the dishmachine if mounting dishmachine for a corner installation and attaching side tables. Corner installation will trap panel making it difficult to remove. Specifications table dimensions notice 20 1/2” (52.1 cm) opening 25 1/4” (64.1 ...
07610-003-92-84-q 6 model designation: xl-e xl-e-lth xl hh operating capacity: racks per hour 39 39 39 dishes per hour 975 975 975 glasses per hour 1404 1404 1404 tank capacity (gallons): wash tank 1.02 (40.2 gph) 1.02 (40.2 gph) 1.61 (62.8 gph) electrical loads (as applicable): wash motor hp 1 1 1 ...
07610-003-92-84-q 7 all electrical ratings provided in this manual are for reference only. Always refer to the machine data plate to get exact electrical information for this machine. All electrical work performed on machines should be done in accordance with applicable local, state, territorial, an...
07610-003-92-84-q 8 instructions installation before installing the unit, check the packaging and machine for damage. If the packaging is damaged, the machine might also be damaged. If there is damage to both the packaging and machine, do not throw away the packaging. The dishmachine has been inspec...
07610-003-92-84-q 9 water supply connection: water hardness of 3 gpg or lower pressure regulator shock absorber connecting the drain line if water hardness tests at 3 gpg or lower, install the water supply line to the dishmachine’s incoming water connection point using copper pipe (or order the flex...
07610-003-92-84-q 10 electrical and grounding connections must comply with the applicable portions of the national electrical code ansi/nfpa 70 (latest edition) and/or other electrical codes. Disconnect electrical power supplies and place a tag at the disconnect switch to indicate that you are worki...
07610-003-92-84-q 11 1. Ensure the power switch is in the off position and apply power to the dishmachine. 2. Check the incoming power at the terminal block and ensure it corresponds to the voltage listed on the data plate. If not, contact a qualified service agency to examine the problem. Caution! ...
07610-003-92-84-q 12 instructions installation priming chemical feeder pumps 5. Rinse-aid is dispensed as required into the final rinse. The amount of rinse-aid might need to be adjusted depending on water hardness and results. 6. Sanitizer is dispensed into the final rinse. The amount of sanitizer ...
07610-003-92-84-q 13 the cam timer is a 1-minute, 30-second, 8-cam timer that controls the operation of the dishmachine. The following is a description of the setpoints for each cam and the function of each switch. Function: when the machine is in operation mode the notch is in the home position. Th...
07610-003-92-84-q 14 function: the fill solenoid cam works off the normally-closed contacts of cam 5. The switch is held open by the cam until it drops into the notch of the cam. This energizes the fill solenoid, which starts filling the machine with water. After a 10-second delay, the cam reverses ...
07610-003-92-84-q 15 false panel weldment 05700-002-51-66 false panel kit 05700-003-12-93 rack rail removed and repositioned for a corner operation insert this side first bottom of side panel xl-e/xl-e-lth false panel instructions installation false panel positioned in unit. The false panel will mou...
07610-003-92-84-q 16 rack rail removed and repositioned for a corner operation. Xl hh false panel instructions installation false panel weldment 05700-002-52-54 false panel kit 05700-002-52-89 false panel positioned in unit. The false panel will mount inside of the dishmachine. 1. Remove the rack as...
07610-003-92-84-q 17 operating range before operating the unit, verify the following: 1. The sump strainer and pan strainer are in place and clean. 2. The drain stopper is installed. 3. The wash/rinse arms are installed and secure. To place the unit in standby, flip the "off/on/fill" switch to the o...
07610-003-92-84-q 18 the first rack of ware that you place into the unit can have the effect of quickly reducing the temperature of the wash tank. This is because you are introducing cold materials into the dishmachine and the unit has to circulate water to activate the heating cycle. You might have...
07610-003-92-84-q 19 shutdown & cleaning 1. Turn machine off by flipping the “off/on/fill” switch to the “off” position. 2. Open the door. 3. Remove the drain stopper and allow tub to drain. 4. Remove the sump strainer and pan strainer. 5. Use a hand-scraper to scrape foodsoil into a trash basket. 6...
07610-003-92-84-q 20 operating instructions operation 8. Verify the nozzles and arms are free from obstruction. If clogged, remove end- caps, clean nozzles with a brush, and flush with fresh water. 9. Replace end-caps and ensure they have been tightened. 10. Spray or wipe out interior of machine. 11...
07610-003-92-84-q 21 1. Follow filling the wash tub section. 2. Add deliming solution per chemical supplier’s instructions. 3. Close the door. 4. Flip the normal/delime switch on the back of the control box to delime. 5. Run machine the period of time recommended by chemical supplier. 6. Wait five m...
07610-003-92-84-q 22 the manufacturer highly recommends that any maintenance and repairs not specifically discussed in this manual be performed only by qualified service personnel. Performing maintenance on your dishmachine may void your warranty, lead to larger problems, or even cause harm to the o...
07610-003-92-84-q 23 problem possible cause remedy dishmachine will not run, no voltage at wash relay terminals l1 and t1. 1. Service disconnect switch off or faulty. 2. Branch circuit breaker tripped/fuse blown. 3. Loose or broken connection to dishmachine. 1. Turn disconnect on. 2. Reset or replac...
07610-003-92-84-q 24 problem possible cause remedy dishmachine fills slowly and/ or the rinse is weak. 1. Clogged or obstructed rinse arms. 2. Low incoming water pressure. 3. Y-strainer is clogged. 1. Remove and clean the rinse arms. 2. Adjust the water pressure regulator to ensure that there is 15 ...
07610-003-92-84-q 25 1 11 19 28 18 10 9 8 7 4 3 2 4 5 9 9 15 16 17 27 25 26 22 24 12 13 14 20 21 23 29 xl-e control box parts 19a.
07610-003-92-84-q 26 item qty description part number 1 1 control box top 05700-003-81-49 2 1 decal, warning–disconnect power 09905-004-08-16 3 1 upper decal, xl-e 09905-004-00-07 4 2 chemical feeder pump assembly, 36 rpm (208 v units) chemical feeder pump assembly, 36 rpm (115 v units) 05700-003-78...
07610-003-92-84-q 27 xl-e-lth control box parts d item qty description part number xl-e-lth control box complete assembly 05700-004-49-01 1 1 box, control assembly 05700-004-49-02 2 1 bracket, terminal block 05700-004-51-59 3 2 bracket, pressure switch 05700-004-08-99 4 1 bracket, timer mounting 057...
07610-003-92-84-q 28 item qty description part number 8 1 contactor, 30 a 05945-004-43-74 9 9a 1 1 thermostat, elan electric (dual) probe, thermistor 4” 06685-004-17-27 06685-004-17-26 10 1 terminal board 05940-021-94-85 11 1 terminal block, 3-pole 05940-011-48-27 12 1 contactor, 30 a 05945-002-74-2...
07610-003-92-84-q 29 detail a pump installation detail a (2 plc's) (4 plc's) (3 plc's) (3 plc's) (2 plc's) (2 plc's) (6 plc's) (6 plc's) (4 plc's) (2 plc's) (2 plc's) (2 plc's) (4 plc's) (3 plc's) (2 plc's) (4 plc's) 39 19 16 15 4 18 13 1 30 26 2 24 34 32 3 5 6 23 38 20 27 14 14 33 28 13 35 13 37 10...
07610-003-92-84-q 30 item qty description part number high hood control box complete assembly 05700-004-25-41 1 1 control box weldment 05700-003-81-49 2 3 light, red 05945-504-07-18 3 1 light, green 05945-504-08-18 4 1 switch, carling 05930-301-21-18 5 1 counter, 115 v 05990-111-35-38 1 counter, 208...
07610-003-92-84-q 31 item qty description part number 30 1 upper decal 09905-004-30-01 31 2 bracket, pressure switch 05700-004-08-99 32 1 decal, wash/rinse 09905-002-82-46 33 6 p-clamp 1/4" id 05975-002-61-42 34 1 temperature gauge 06685-111-68-49 35 35a 1 8 timer microswitch, timer 05945-004-11-78 ...
07610-003-92-84-q 32 parts section technical manual (07610-003-92-84) 25 pagecreated:01/30/2012 revised:n/a chemical feeder pump components motor, 14 rpm 115v rinse aid feeder pump 04320-111-35-13 motor, 14 rpm 240v rinse aid feeder pump 04320-111-47-46 motor, 36 rpm 115v detergent/sanitizer feeder ...
07610-003-92-84-q 33 item qty description part number 1 1 rear housing 04320-111-37-09 2 1 motor, 14 rpm 115 v rinse-aid feeder pump 04320-111-35-13 motor, 14 rpm 208/230 v, rinse-aid feeder pump 04320-111-47-46 1 motor, 36 rpm 115 v, detergent/sanitizer feeder pump 04320-111-35-14 motor, 36 rpm 208...
07610-003-92-84-q 34 before ordering plumbing assembly or plumbing parts, see the note on the next page. 1 2 7 8 4 6 3 17 5 xl-e hood assembly parts complete inlet plumbing assembly 05700-004-34-44 14 13 12 11 10 9 15 16 18 notice.
07610-003-92-84-q 35 1 1 control box assembly, 115 v control box assembly, 208 v 05700-004-01-65 05700-004-16-66 2 1 hood, weldment 05700-004-08-68 3 10 locknut, 1/4-20 with nylon insert 05310-374-01-00 4 2 hood support 05700-002-78-99 5 6 bolt, 1/4-20 x 1/2” 05305-274-02-00 6 12 washer, ss 1/4” 053...
07610-003-92-84-q 36 xl-e-lth hood assembly parts complete inlet plumbing assembly 05700-004-49-05 1 2 3 4 6 5 6 7 8 9 10 12 13 14 15 17 16 18 19 20 21 22 22 11.
07610-003-92-84-q 37 xl-e-lth hood assembly parts 1 1 control box assembly, xl-e-lth 05700-004-49-01 2 1 hood, weldment 05700-004-08-68 3 1 gasket, air-gap 05330-002-14-48 4 1 air-gap 05700-004-34-42 5 1 nipple, 3/4" x 2" brass 04730-207-46-00 6 2 elbow, 3/4", 90-degree brass 04730-206-13-00 7 1 nip...
07610-003-92-84-q 38 8 1 2 12 11 10 7 4 6 15 16 17 9 3 5 xl hh hood assembly parts complete inlet plumbing assembly 05700-004-34-44 14 13 18 before ordering plumbing assembly or plumbing parts, see the note on the next page. Notice.
07610-003-92-84-q 39 item qty description part number xl hh hood assembly parts 1 1 control box assembly, 115 v control box assembly, 208 v 05700-004-25-41 05700-004-30-24 2 1 hood, weldment 05700-004-24-96 3 10 locknut, 1/4-20 with nylon insert 05310-374-01-00 4 2 hood support 05700-004-13-45 5 6 b...
07610-003-92-84-q 40 1 2 24, 18 10, 11, 12 13 9 15, 16 7 8 5 22 4 14 3 6 23, 18 17, 18 19, 11, 12 20 21, 25 3a 3b 3c 3d 3e 3f xl-e/xl-e-lth door assembly parts.
07610-003-92-84-q 41 item qty description part number 1 1 arm, cantilever 05700-031-50-67 2 2 spring pin, 1/4” dia. X 1 1/8” 05315-407-06-00 3 2 yoke assembly 05700-000-75-77 3a 1 cotter pin 05315-207-01-00 3b 1 yoke 05700-000-75-78 3c 1 clevis pin 05315-700-01-00 3d 2 nylon washer 05311-369-03-00 3...
07610-003-92-84-q 42 26 2 1 8 17 24 25 8 23 9 20 22 21 9 7 3 6 5 9 7 16 12 7 19 18 11 10 13 4 8 14 27 27c 27e 27d 27a 27b 15 xl hh door assembly parts.
07610-003-92-84-q 43 item qty description part number 1 1 door, front outer 05700-004-14-21 2 1 door, left outer 05700-004-14-19 3 1 door, right outer 05700-004-14-17 4 2 bracket, door connecting 05700-004-14-23 5 1 handle, door front 05700-004-14-30 6 2 plug, cantilever 05340-011-35-00 7 22 washer,...
07610-003-92-84-q 44 3 1 2 4 5 6 item qty description part number 1 1 bearing assembly 05700-021-35-97 2 1 o-ring, 117-s70 silicon 05330-002-60-69 3 2 wash arm end-cap 05700-011-35-92 4 1 wash arm 05700-003-57-70 wash arm assembly 05700-003-59-35 wash arm assembly parts 1 2 3 4.
07610-003-92-84-q 45 item qty description part number 1 2 bolt, 3/8-16 x 3/8" ss 05306-011-36-95 2 1 casting, upper wash manifold 05700-031-34-82 3 4 3/8" lockwasher, ss 05311-276-01-00 4 4 3/8" hex nut, ss 05310-276-01-00 5 2 bolt, 3/8-16 x 1 1/4" ss 05305-276-10-00 6 1 lower wash manifold 05700-00...
07610-003-92-84-q 46 item qty description part number 1 1 tub assembly, xl-e/xl-e-lth 05700-003-78-39 1 tub assembly, xl hh 05700-004-27-28 2 1 rack guide assembly 05700-031-36-76 3 1 bulkhead fitting, 1/2” 04730-011-45-21 4 1 1 clamp, nylon lock nut, 10-24 ss 04730-011-39-01 05310-373-01-00 5 1 was...
07610-003-92-84-q 47 item qty description part number 1 1 pump and motor assembly 06105-004-24-80 2 1 pump drain hose 05700-004-08-52 3 2 clamp, 7/16” to 25/32” 04730-011-36-05 4 1 clamp, 5 5/8” to 6” 04730-011-34-90 5 1 sump weldment 05700-003-78-41 6 1 sump gasket 05330-003-78-31 7 9 lock nut, 1/4...
07610-003-92-84-q 48 drain, seat 05700-021-34-38 gasket, spillway 05700-111-34-52 lock nut, ¼-20 s/s 05310-374-01-00 connection, drain link 05700-002-38-10 drain link 05700-003-78-49 spillway weldment 05700-003-52-13 spillway assembly parts 05700-004-37-18.
07610-003-92-84-q 49 complete pump and motor assembly 06105-004-24-80 pump dishcharge hose (not shown) 05700-003-78-50 hose clamp, 1 5/16" to 2 1/4" s/s (not shown) 04730-719-18-00 (2 required) case cap screw 05305-356-04-00 shim kit 05700-002-82-58 case o-ring 05330-002-81-83 seal plate 05700-002-8...
07610-003-92-84-q 50 xl-e-lth booster tank assembly parts 16.
07610-003-92-84-q 51 item qty description part number complete booster tank assembly 05700-004-52-09 1 1 booster tank 05700-004-52-23 2 1 plate, booster tank base 05700-004-48-90 3 4 bracket, booster mount 05700-004-48-83 4 1 bracket, booster tank 05700-004-52-08 5 2 plumbing, booster inlet/outlet 0...
07610-003-92-84-q 52 frame assembly parts item qty description part number 1 1 frame weldment 05700-003-78-38 2 1 splash shield 05700-004-01-54 3 1 strainer 05700-004-09-08 4 1 strainer stop 05700-004-18-33 5 1 accumulator 05700-004-08-39 6 4 adjustable foot 05340-108-01-03 7 1 1 screw, 1/4-20 x 1 1...
07610-003-92-84-q 53 ball stopper 05700-121-35-54 blue chemical tubing (120") 05700-011-37-17 red chemical tubing (120") 05700-011-37-15 white chemical tubing (120") 05700-011-37-13 chemical tubing stiffener 05700-002-66-49 bulk head fitting 04730-011-45-21 flanged bullet foot (optional) 05340-002-3...
07610-003-92-84-q 54 schematics xl-e/xl hh 115 v, 60 hz, 1-phase.
07610-003-92-84-q 55 schematics xl-e/xl hh 208 v, 60 hz, 1-phase.
07610-003-92-84-q 56 schematics xl-e-lth 208/230 v, 60 hz, 1/3 phase.
58 jackson wws, inc. • 6209 n. Us hwy 25e • gray, ky 40734 usa 1.888.800.5672 • www.Jacksonwws.Com conserver ® xl-e/xl-e-lth/xl hh manual • 07610-003-92-84-q.