- DL manuals
- Jackson Grills
- Ice Maker
- AZ-20A
- User Manual
Jackson Grills AZ-20A User Manual
Summary of AZ-20A
Page 1
Automatic outdoor ice maker user’s manual be sure unit is standing upright 24 hours prior to plug-in model: az-20a.
Page 2: Table Of Contents
Table of contents page ice maker safety............................................................................................................... 2 important safeguards.............................................................................................. 3 - 5 technical information .......
Page 3: Ice Maker Safety
Ice maker safety your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can injure or ki...
Page 4: Important Safeguards
Important safeguards before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. Jackson grills strongly recommends that you have a professional install your new machine. The warranty may be affected or voided by an incorrect ...
Page 5: Save These Instructions
• use two or more people to move and install ice maker. Failure to do so can result in back or other injury. • to ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed. Choose a well-ventilated area with temperatures above 45°f (7°c) and below 110° f (43...
Page 6: Technical Information
Electrical connection do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded. The power cord of this appliance is equipped with a 3-prong grounding plug that mates with a standard 3-prong grounding wa...
Page 7: Introduction
Introduction the jackson grills az-20a ice maker produces hard, crystal-clear, gourmet cube ice, and offers convenience for homeowners and hotel guests. It can be used both indoors and outdoors. An insulated, removable ice storage bin is included. This user’s manual is intended as a resource for per...
Page 8: Component Locations
Component locations 7.
Page 9: Unpacking
Unpacking ice maker installation excessive weight hazard use two or more people to move and install ice maker. Failure to do so can result in back or other injury. Remove packaging materials important: do not remove any permanent instruction labels or the data label on your ice maker. Remove tape an...
Page 10
• this ice maker should be installed by qualified personnel. • to ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed. • when installing the ice maker under a counter, follow the recommended spacing dimensions shown on the previous page. Allow 2/5" (10...
Page 11: Electrical Requirements
Electrical requirements electrical shock hazard plug into a grounded 3- prong outlet. Never remove the ground prong from the plug. Never use an adapter. Never use an extension cord. Failure to follow these instructions can result in fire, electrical shock or death. Before you move your ice maker int...
Page 12: Installation Of Casters
Installation of casters casters are provided with the ice maker. They are ideal for rolling the unit from place to place outdoors. If a mobile installation is chosen, you must install the casters. Screw holes use two or more people when installing or removing casters. • tip unit to the right so ther...
Page 13: Reversing The Door Swing
1. Place a carpenter’s level on t op of the product to see if the ice maker is level from front to back and side to side. 2. Adjust the height of the legs as follows: turn the leveling legs to the right to lower that side of the ice maker. Turn the leveling legs to the left to raise that side of the...
Page 14: Water Supply
To replace door on hinges: 1. Using a flat screwdriver , remove the plug buttons from the screw holes opposite the door hinges, top and bottom. Set aside. 2. Remove the bottom hinge and place it on the opposite side at the bottom of the door. 3. Position the door on the bottom hinge. 4. Align the do...
Page 15: Drain
Connecting the water line: 1. Turn off main water supply. Turn on the nearest faucet long enough to clear the line of water. 2. Find a 1/2” to 3/4” vertical cold water pipe near the installation location. The distance should be less than 9 feet. The water supply hose provided with the ice maker is a...
Page 16: Installation Types
Installation types this ice maker has been designed for mobile (free-standing), enclosed (as under a cabinet) or built-in (sealed) installation, indoor or outdoor. In any case, there must be adequate air space around the unit for proper ventilation. (see diagrams on page 8.) mobile installation: a m...
Page 17: Operation
Operation final check list before operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Did you clean the ice storage bin? 3. Have the installation instructions been followed, including connecting the machine to water and electricity? 4. Ha...
Page 18
2. After three minutes, the machine will automatically go into the ice-making stage, and the sound of flowing water will be heard. 3. When the batch of ice has been fully formed , the ice will automatically be harvested to the ice storage bin. 4. When the ice storage bin is full, the sheet of cubes ...
Page 19
How the machine uses the water the ice maker begins with a fixed charge of water that is contained in the water trough. As the water flows to the freezing evaporator surface, the portion of water that does not contain mineral impurities will freeze and stick to the ice cube molds. The water containi...
Page 20: Normal Sounds
Normal sounds your new ice maker may make sounds that are unfamiliar to you. Most of the new sounds are normal. Hard surfaces like the floor and walls can amplify the sounds. The following describes the kinds of sounds that might be new to you and what may be causing them. • rattling noises may come...
Page 21: Cleaning And Maintenance
Cleaning and maintenance if the ice maker is left unused for a long time, before the next use it must be thoroughly cleaned. Follow carefully any instructions provided for cleaning or use of sanitizing solution. Do not leave any solution inside the ice maker after cleaning. Periodic cleaning and pro...
Page 22: Interior Cleaning
Interior cleaning the ice storage bin should be sanitized occasionally. Clean the trough before the ice maker is used for the first time and reused after stopping for an extended period of time. It is usually convenient to sanitize the trough after the ice-making system has been cleaned and the stor...
Page 23: Ice-Making System Cleaning
Do not touch the condenser fins. They are sharp and can be damaged easily. Water distribution tube cleaning when you find that the ice cubes are incompletely formed or the output of ice cubes is low, the water distribution tube may be blocked. Set the power switch to off, rotate the water distributi...
Page 24
Note: the unit will automatically shut down the cleaning program after 30 minutes, or you can stop it by pressing the clean switch again, and the machine will automatically progress to the ice-making stage. 4. Allow 20 minutes for proper cleaning. After cleaning, turn the machine off at the power sw...
Page 25: Major Functions
Major functions 1. Completely automatic operation 2. When the ice storage bin is full of ice, the machine stops making ice and proceeds to the cold preservation stage automatically. It starts making ice again once the cubes are removed. 3. The fan motor responds to the ambient temperature. If it is ...
Page 26: Troubleshooting
Troubleshooting before calling for service if the unit appears to be malfunctioning, read through the operation section of this manual first. If the problem persists, check the troubleshooting guide below and on the following page. The problem could be something very simple that can be solved withou...
Page 27
Problem possible cause probable correction cubes are partially formed or are white at the bottom. Not enough water in the water trough. Check if the water supply pressure is below 15 psig. Check water supply; filter may be restricted. Check for a water leak at the water trough. Noise during operatio...
Page 28
Jackson grills limited warranty description of limited warranty this limited warranty is given by jackson grills to the original purchaser of the refrigeration equipment supplied by jackson grills as long as the equipment remains in the possession of the original purchaser. Your jackson grills refri...