- DL manuals
- Jackson Grills
- Ice Maker
- AZ-20A
- User Manual
Jackson Grills AZ-20A User Manual
Summary of AZ-20A
Page 1
Automatic outdoor ice maker user’s manual be sure unit is standing upright 24 hours prior to plug-in model: bbq10700
Page 2: Table of Contents
1 table of contents page ice maker safety............................................................................................................... 2 important safeguards.............................................................................................. 3 - 5 technical information .....
Page 3: Ice Maker Safety
2 ice maker safety your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can injure or ...
Page 4: Important Safeguards
3 important safeguards before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. Jackson grills strongly recommends that you have a professional install your new machine. The warranty may be affected or voided by an incorrec...
Page 5
4 • use two or more people to move and install ice maker. Failure to do so can result in back or other injury. • to ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed. Choose a well-ventilated area with temperatures above 45 °f (7°c) and below 110 ° f...
Page 6: Save These Instructions
5 save these instructions electrical connection do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded. The power cord of this appliance is equipped with a 3-prong grounding plug that mates with a sta...
Page 7: Introduction
6 introduction the jackson grills bbq10700 ice maker produces hard, crystal-clear, gourmet cube ice, and offers convenience for homeowners and hotel guests. It can be used both indoors and outdoors. An insulated, removable ice storage bin is included. This user’s manual is intended as a resource for...
Page 8: Component Locations
7 component locations.
Page 9: Ice Maker Installation
8 installation clearances ice maker installation unpacking remove packaging materials important: do not remove any permanent instruction labels or the data label on your ice maker. Remove tape and glue from your ice maker before using. • to remove any remaining tape or glue, rub the area briskly wit...
Page 10
9 • this ice maker should be installed by qualified personnel. • to ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed. • when installing the ice maker under a counter, follow the recommended spacing dimensions shown on the previous page. Allow 2/5" (...
Page 11: Electrical Requirements
10 electrical requirements before you move your ice maker into its final location, be sure you have the proper electrical connection: a standard electrical supply (115v ac only, 60hz, 15a), properly grounded in accordance with the national electrical code and local codes and ordinances, is required....
Page 12: Leveling The Ice Maker
11 leveling the ice maker it is important for the ice maker to be leveled in order to work properly; otherwise water will not flow as it should through the evaporator (ice mold). Ice production will be less than normal, and operation will be noisy. The ice maker can be raised or lowered by four leve...
Page 13: Water Supply
12 to remove door from hinges: 1. Remove the top hinge cover. 2. Using a phillips screwdriver, remove the screws, then remove top hinge mat and top hinge. Keep the parts together and set them aside. 3. Lift the door off of the bottom hinge and turn it upside down so that the handle is on the right. ...
Page 14: Drain
13 connecting the water line: 1. Turn off main water supply. Turn on the nearest faucet long enough to clear the line of water. 2. Find a 1/2” to 3/4” vertical cold water pipe near the installation location. The distance should be less than 9 feet. The water supply hose provided with the ice maker i...
Page 15: Installation Types
14 installation types this ice maker has been designed for mobile (free-standing), enclosed (as under a cabinet) or built-in (sealed) installation, indoor or outdoor. In any case, there must be adequate air space around the unit for proper ventilation. (see diagrams on page 8.) mobile installation: ...
Page 16: Operation
15 ice- harvesting stage ice- making stage operation final check list before operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker? 2. Did you clean the ice storage bin? 3. Have the installation instructions been followed, including connecting ...
Page 17: How The Machine Makes Ice
16 2. After three minutes, the machine will automatically go into the ice-making stage, and the sound of flowing water will be heard. 3. When the batch of ice has been fully formed , the ice will automatically be harvested to the ice storage bin. 4. When the ice storage bin is full, the sheet of cub...
Page 18
17 how the machine uses the water the ice maker begins with a fixed charge of water that is contained in the water trough. As the water flows to the freezing evaporator surface, the portion of water that does not contain mineral impurities will freeze and stick to the ice cube molds. The water conta...
Page 19: Normal Sounds
18 normal sounds your new ice maker may make sounds that are unfamiliar to you. Most of the new sounds are normal. Hard surfaces like the floor and walls can amplify the sounds. The following describes the kinds of sounds that might be new to you and what may be causing them. • rattling noises may c...
Page 20: Cleaning and Maintenance
19 cleaning and maintenance periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets, or there are other special considerations. What should...
Page 21: Interior Cleaning
20 interior cleaning the ice storage bin should be sanitized occasionally. Clean the trough before the ice maker is used for the first time and reused after stopping for an extended period of time. It is usually convenient to sanitize the trough after the ice-making system has been cleaned and the s...
Page 22: Ice-Making System Cleaning
21 water distribution tube cleaning when you find that the ice cubes are incompletely formed or the output of ice cubes is low, the water distribution tube may be blocked. Set the power switch to off, rotate the water distribution tube, and locate the holes in the distribution tube. Using a toothpic...
Page 23
22 note: the unit will automatically shut down the cleaning program after 30 minutes, or you can stop it by pressing the clean switch again, and the machine will automatically progress to the ice-making stage. 4. Allow 20 minutes for proper cleaning. After cleaning, turn the machine off at the power...
Page 24: Major Functions
23 major functions 1. Completely automatic operation 2. When the ice storage bin is full of ice, the machine stops making ice and proceeds to the cold preservation stage automatically. It starts making ice again once the cubes are removed. 3. The fan motor responds to the ambient temperature. If it ...
Page 25: Troubleshooting
24 troubleshooting before calling for service if the unit appears to be malfunctioning, read through the operation section of this manual first. If the problem persists, check the troubleshooting guide below and on the following page. The problem could be something very simple that can be solved wit...
Page 26
25 problem possible cause probable correction check if the water supply pressure is below 15 psig. Check water supply; filter may be restricted. Cubes are partially formed or are white at the bottom. Not enough water in the water trough. Check for a water leak at the water trough. The legs are not l...