1. DL manuals
  2. Jacobsen
  3. Lawn Mower
  4. Eclipse 2
  5. Technical Manual

Jacobsen Eclipse 2 Technical Manual

Other manuals for Eclipse 2: Technical Manual, Technical Manual

Summary of Eclipse 2

  • Page 1

    Technical manual when performance matters. ™ warning if incorrectly used, this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers, and should read the entire manual before attempting to set up, operate, adjust, or servi...

  • Page 2

    © 2012, jacobsen, a textron company/textron innovations inc. “all rights reserved, including the right to reproduce this material or portions thereof in any form.” this manual contains safety, operating, adjustment, maintenance, troubleshooting instructions and parts list for your new jacobsen machi...

  • Page 3

    3 table of contents 1 safety 1.1 operating safety . . . . . . . . . . . . . . . . . . . . . . 4 1.2 important safety notes . . . . . . . . . . . . . . . . . 5 2 specifications 2.1 product identification . . . . . . . . . . . . . . . . . . 6 2.2 mower . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4: Warning

    1 safety 4 1 safety 1.1 operating safety ______________________________________________________ 1. Safety is dependent upon the awareness, concern and prudence of those who operate or service the equipment. Never allow minors to operate any equipment. 2. It is your responsibility to read this manual...

  • Page 5: Warning

    Safety 1 5 1.2 important safety notes ________________________________________________ this safety alert symbol is used to alert you to potential hazards. Danger - indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning - indicates a potenti...

  • Page 6

    2 specifications 6 2 specifications 2.1 product identification _________________________________________________ 63334 ............................ Eclipse ® 118 base unit with 18 in. (457 mm) 11 blade reel and incommand™ control system. Gen-set power module. 63343 ............................ Eclip...

  • Page 7

    Specifications 2 7 2.2 mower __________________________________________________________________ reel..................................7, 9, 11, or 15 blades, hardened high manganese carbon steel. Reel diameter ..................5 in. (127 mm) cutting width ...................18, 22 or 26 in. (457, 5...

  • Page 8

    2 specifications 8 2.6 battery power module ________________________________________________ to ensure the longest battery life possible, the batteries are not shipped with the power module and must be ordered separately. For optimum range and performance use batteries that equal or exceed the amp-h...

  • Page 9: Caution

    Specifications 2 9 2.7 accessories & support literature _____________________________________ contact your area jacobsen dealer for a complete listing of accessories and attachments. Accessories lapping compound (180 grit) ................................... 554598 orange touch-up paint (12 oz. Spra...

  • Page 10

    2 specifications 10 2.8 declaration of conformity ____________________________________________ declaration of conformity ▪ ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ ▪ prohlÁŠenÍ o shodĚ ▪ overensstemmelseserklÆring ▪ conformiteitsverklaring ▪ vastavusdeklaratsioon ▪ vaatimustenmukaisuusvakuutus ▪ declaration de co...

  • Page 11

    Specifications 2 11 cutting width ▪ Широчина на рязане ▪ Šířka řezu ▪ skærebredde ▪ maaibreedte ▪ lõikelaius ▪ leikkuuleveys ▪ largeur de coupe ▪ schnittbreite ▪ Μήκος μισινέζας ▪ vágási szélesség ▪ larghezza di taglio ▪ griešanas platums ▪ pjovimo plotis ▪ tikkonforma mad-direttivi ▪ szerokość cięc...

  • Page 12

    2 specifications 12 signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is established in the community. Подпис на човека, упълномощен да състави декларацията от името н...

  • Page 13

    Decals 3 13 3 decals 3.1 decals _________________________________________________________________ familiarize yourself with the following decals. They are critical to the safe operation of the mower. Replace damaged decals immediately. 4170001 stop 4127335 4169840 rev a danger to prevent injury, dis...

  • Page 14

    3 decals 14 familiarize yourself with the following decals. They are critical to the safe operation of the mower. Replace damaged decals immediately. 4265170 4265171 4172240 read the manual before adjusting front roller weight. Disengaged parking engaged brake reel switch off on 4265172 key switch o...

  • Page 15

    Decals 3 15 to engage traction. 1. Slide bail to the left. 2. Squeeze bail to handle..

  • Page 16: Warning

    4 controls 16 4 controls 4.1 icons ___________________________________________________________________ 4.2 handle controls ______________________________________________________ a. Parking brake – used whenever the mower is left unattended or as a service brake while transporting. Always use transpo...

  • Page 17: Warning

    Controls 4 17 4.3 lcd display _____________________________________________________________ the lcd displays current functional values for the operation of the eclipse mower and sounds one of three types of audible alerts. The lcd operates in one of two modes, operator mode (default), and maintenanc...

  • Page 18

    4 controls 18 operator mode is used by the operator for system voltage information, travel speed, foc setting, reel speed, and total hours on mower. Press the orange buttons (k and l) on the front handle cover to toggle between the different displays. Operator mode is view only, only screen illumina...

  • Page 19

    Controls 4 19 maintenance mode is used to set and adjust all functional values for the eclipse mower. Lcd displays available in maintenance mode are, maintenance hours, backlap, system voltage, travel speed, set foc, reel speed, traction motor current draw, reel motor current draw, total motor curre...

  • Page 20

    4 controls 20 display description to enter maintenance mode, press either orange buttons (k or l) until maintenance mode pin screen is on the display and press black button (j). Use the orange buttons (k or l) to select and the black button (j) to enter the digits for the mechanic mode pin. Note: th...

  • Page 21

    Controls 4 21 gen-set power module - used to indicate the gen-set power module is installed on the mower. This setting is used by system controllers and does not affect operation of mower. Do not operate mower with incorrect power module setting. Press the black button (j) to toggle between the powe...

  • Page 22

    4 controls 22 4.4 frequency of cut ______________________________________________________ the foc (frequency of cut) is the distance, in inches (mm), the machine travels forward between reel blades contacting the bedknife. The foc can be adjusted either by changing the fixed foc setting or by changi...

  • Page 23

    Controls 4 23 15 blade reel foc table , product no 63339, 63341, 63335, 63337, 63348, 63350, 63344, 63346 (standard reel) mow speed reel rpm 1800 1850 1900 1950 2000 2050 2100 2150 2200 2.00 0.078 0.076 0.074 0.072 0.070 0.069 0.067 0.065 0.064 (3.22) (1.987) (1.933) (1.882) (1.834) (1.788) (1.745) ...

  • Page 24

    4 controls 24 11 blade reel foc table, product no. 63334, 63336, 63338, 63340, 63347, 63349, 63343, 63345 (standard reel) mow speed reel rpm 1800 1850 1900 1950 2000 2050 2100 2150 2200 2.0 (3.22) 0.107 (2.709) 0.104 (2.636) 0.101 (2.567) 0.098 (2.501) 0.096 (2.438) 0.094 (2.379) 0.091 (2.322) 0.089...

  • Page 25

    Controls 4 25 9 blade reel foc table, product no. 63340, 63349 (optional reel) mow speed reel rpm 1800 1850 1900 1950 2000 2050 2100 2150 2200 2.0 0.130 0.127 0.124 0.120 0.117 0.114 0.112 0.109 0.107 (3.22) (3.311) (3.222) (3.137) (3.057) (2.98) (2.908) (2.838) (2.772) (2.709) 2.1 0.137 0.133 0.130...

  • Page 26

    4 controls 26 7 blade reel foc table, product no. 63342, 63351 (standard reel) and 63340, 63349 (optional reel) mow speed reel rpm 1800 1850 1900 1950 2000 2050 2100 2150 2200 2.0 0.168 0.163 0.159 0.155 0.151 0.147 0.144 0.140 0.137 (3.22) (4.258) (4.142) (4.033) (3.93) (3.832) (3.738) (3.649) (3.5...

  • Page 27: Notice

    Controls 4 27 4.5 gas power module controls ___________________________________________ m. Engine switch – the engine switch enables and disables the engine ignition system. The engine switch must be in the on position for the engine to run. Turning the engine switch to the off position stops the en...

  • Page 28: Caution

    5 operation 28 5 operation 5.1 daily inspection________________________________________________________ 1. Perform a visual inspection of the entire unit, look for signs of wear, loose hardware, missing or damaged components. 2. Make sure the mower is adjusted to the required cutting height. 3. Make...

  • Page 29: Caution

    Operation 5 29 5.3 operating procedures _________________________________________________ 1. Under no circumstances should the unit be started with operator or bystanders standing in front of the reel. 2. Never run the engine in an enclosed area. 3. Keep hands and feet away from moving parts and cut...

  • Page 30

    5 operation 30 5.4 starting/stopping _____________________________________________________ 1. Prepare power module to energize unit. Battery power module: disconnect battery charger and connect power connector. Gen-set power module: a. Check oil level and fuel supply then open fuel valve lever (p). ...

  • Page 31: Warning

    Operation 5 31 5.5 mowing _________________________________________________________________ 1. Turn power off. Remove the transport wheels (if installed). 2. Engage the reel switch. Start the unit. 3. Position mower slightly off green. A. Adjust traction speed paddle (b) to provide a safe, comfortab...

  • Page 32: Warning

    5 operation 32 5.6 transport wheels (optional) __________________________________________ transport wheels are optional accessories available through your jacobsen dealer. Traction wheels are recommended when not using the mower caddy to move the mower from green to green. 1. Push and hold the kicks...

  • Page 33: Warning

    Operation 5 33 5.8 grass catcher _________________________________________________________ 1. When the basket is about two thirds (2/3) full of grass clippings, move the mower off the green. 2. Stop on a flat surface, disengage o.P.C. Bail, engage parking brake, turn key switch off, and disconnect p...

  • Page 34: Warning

    6 adjustments (all units) 34 6 adjustments (all units) 6.1 general ________________________________________________________________ 1. Adjustments and maintenance should always be performed by a qualified technician. If proper adjustment cannot be made, contact an authorized jacobsen dealer. 2. Repl...

  • Page 35: Caution

    Adjustments (all units) 6 35 6.4 handle _________________________________________________________________ 1. To adjust the angle of the handle bar (f), loosen screw (d) on both sides of the mower and adjust the handle bar to the desired position. 2. After adjusting handle bar, adjust bracket (e) so ...

  • Page 36: Caution

    6 adjustments (all units) 36 6.6 front roller weight ___________________________________________________ the weight on the front roller is adjustable. Adjust the front roller weight as required to meet your turf needs. 1. Battery power module: to adjust front roller weight, disconnect power connecto...

  • Page 37: Notice

    Adjustments (all units) 6 37 6.7 torque specification ___________________________________________________ jacobsen uses grade 5 plated bolts as standard, unless otherwise noted. For tightening plated bolts, use the value given for lubricated. Notice all torque values included in these charts are app...

  • Page 38: Warning

    7 fixed head reel adjustments 38 7 fixed head reel adjustments 7.1 general ________________________________________________________________ 1. Adjustments and maintenance should always be performed by a qualified technician. If proper adjustment cannot be made, contact an authorized jacobsen dealer....

  • Page 39: Notice

    Fixed head reel adjustments 7 39 7.3 bedknife adjustment ___________________________________________________ 1. Adjuster (a) is used to increase or decrease the spring load on the bedknife. Adjuster (b) is used to move the bedknife to the reel or away from the reel. 2. Once the spring is totally col...

  • Page 40: Warning

    8 floating head reel adjustments 40 8 floating head reel adjustments 8.1 general ________________________________________________________________ 1. Adjustments and maintenance should always be performed by a qualified technician. If proper adjustment cannot be made, contact an authorized jacobsen d...

  • Page 41: Notice

    Floating head reel adjustments 8 41 8.3 bedknife adjustment ___________________________________________________ 1. Read section 8.2 before making the adjustment. 2. Start adjustment at the leading end of the reel, followed by the trailing end. The leading end of the reel blades is that end which pas...

  • Page 42: Notice

    8 floating head reel adjustments 42 8.5 cutting height _________________________________________________________ note: always make the reel to bedknife adjustment before adjusting height of cut. (sections 8.2 and 8.3). 1. Push kickstand down and tip mower back on it’s handle. 4. Set desired cutting ...

  • Page 43: Warning

    Battery power module 9 43 9 battery power module 9.1 safety __________________________________________________________________ batteries contain dilute sulfuric acid which can result in severe burns. Hydrogen gas is formed within a battery during the charging cycle. Hydrogen in concentrations of 4% ...

  • Page 44

    9 battery power module 44 9.3 maintenance ___________________________________________________________ tool list insulated wrench, 3/8” insulated wrench, 11/32” standard screwdriver before charging batteries inspect the connector housings of the battery charger and battery pack for dirt or debris. It...

  • Page 45: Warning

    Battery power module 9 45 9.5 battery charger _______________________________________________________ the battery charger is designed to fully charge the battery pack. Read the instruction manual included with the charger for proper operating procedure. Before charging, the following should be obser...

  • Page 46: Warning

    9 battery power module 46 9.6 battery installation __________________________________________________ if the batteries have been cleaned and any acid in the battery tray area neutralized, no corrosion to the surrounding area should be present. Any corrosion found should be immediately removed with a...

  • Page 47: Caution

    Battery power module 9 47 9.7 replacing battery pack________________________________________________ the battery pack (a) is designed to be easily lifted out and replaced. This allows the mower to quickly return to service should the batteries become discharged or fail. Additional battery packs are ...

  • Page 48: Notice

    10 gen-set power module 48 10 gen-set power module 10.1 engine _________________________________________________________________ important: a separate engine manual, prepared by the engine manufacturer, is supplied with the power module. Read the engine manual carefully until you are familiar with t...

  • Page 49

    Gen-set power module 10 49 10.3 engine oil change ______________________________________________________ perform initial oil change after the first 20 hours of operation. Change oil every 100 hours thereafter. 1. To change engine oil, attach a 7/16 in. (11 mm) i.D. Hose (a) to oil drain valve (b). P...

  • Page 50: Warning

    10 gen-set power module 50 10.5 fuel ____________________________________________________________________ handle fuel with care - it is highly flammable. Use an approved container, the spout must fit inside the fuel filler neck. Avoid using cans and funnels to transfer fuel. • store fuel according t...

  • Page 51: Warning

    Maintenance 11 51 11 maintenance 11.1 general ________________________________________________________________ 1. Adjustment and maintenance should always be performed by a qualified technician. If proper adjustments cannot be made, contact an authorized jacobsen dealer. 2. Inspect the equipment on ...

  • Page 52

    11 maintenance 52 11.4 backlapping and grinding _____________________________________________ check for damage to the bedknife and reel blades. Refer to (section 6.2). 1. Determine if backlapping or grinding will restore the proper cutting edge. 2. For optimum performance use a bedknife grinder to t...

  • Page 53: Caution

    Maintenance 11 53 11.5 storage ________________________________________________________________ general 1. Wash the mower thoroughly and lubricate. Repair and paint damaged or exposed metal. 2. Inspect the mower, tighten all hardware, replace worn or damaged components. 3. Clean the tires thoroughly...

  • Page 54

    12 troubleshooting 54 12 troubleshooting 12.1 general ________________________________________________________________ the troubleshooting chart below lists basic problems that may occur during start-up and operation. For more detailed information, contact your area jacobsen dealer. Symptoms possibl...

  • Page 55: Warning

    Maintenance & lubrication charts 13 55 13 maintenance & lubrication charts 13.1 general ________________________________________________________________ the mower was designed for minimum lubrication. Over greasing will produce high loads on the bearings; thereby reducing the performance of the mach...

  • Page 56

    13 maintenance & lubrication charts 56 13.3 lubrication chart _____________________________________________________ f c d b a l 4 l 6 l 6 l7 e ● ● ● ● ● l 3 l l 5 2 l 1 l l 5 l 5 2 l 2 l 1 l 1 l 1 l 1 l 1 l 1 - reel roller bearing l 2 - reel motor bearing housing l 3 - right side traction drum beari...

  • Page 57

    Parts catalog 14 57 14 parts catalog 14.1 how to use the parts catalog _________________________________________ abbreviations n/s - not serviced separately, can only be obtained by ordering main component or kit. Ar -variable quantity or measurement is required to obtain correct adjustment. Symbols...

  • Page 58: Eclipse

    58 ® dry erase marker only 1 2 3 4 5 6 6 29 7 8 9 9 10 11 12 13 14 15 16 17 18 19 20 21 21 22 22 23 23 24 24 25 25 26 27 28 4265172 4265171 4265170 eclipse 2 1.1 handle covers serial no. All.

  • Page 59: Eclipse

    59 > change from previous revision item part no. Qty. Description serial numbers/notes 1 ref 1 handle assembly see 2.1 2 4254050 1 control lever 3 4127340 1 knob 4 453017 1 flat washer, 1/2 5 454025 ar spring washer, 1/2 6 366708 2 bearing, flanged 7 461381 1 roll pin, 3/16 x 13/16” 8 2000067 1 leve...

  • Page 60: Eclipse

    60 1 2 3 4 5 6 6 7 8 9 10 11 12 13 14 26 15 16 17 18 19 20 21 22 23 24 25 eclipse 2 2.1 handle assembly serial no. All.

  • Page 61: Eclipse

    61 > change from previous revision item part no. Qty. Description serial numbers/notes 1 4256578 1 handle 2 4136328 1 plate, tilt 3 434029 4 screw, 1/4-20 x 1” hex socket 4 453023 4 flat washer, 1/4 5 446130 4 lockwasher, 1/4 heavy 6 443102 6 nut, 1/4-20 hex 7 4136325 1 bail 8 4147696 1 handle, over...

  • Page 62: Eclipse

    62 1 1 2 2 3 3 4 5 6 7 8 8 9 9 10 10 11 11 12 12 1 1 2 2 3 3 4 5 6 7 8 8 9 10 10 11 11 12 12 13 eclipse 2 118 and 118f 63334 63343 63335 63344 63336 63345 63337 63346 eclipse 2 122, 122f, and 126 63338 63347 63339 63348 63340 63349 63341 63350 63342 63351 handle assembly 12 eclipse 2 3.1 handle to f...

  • Page 63: Eclipse

    63 > change from previous revision item part no. Qty. Description serial numbers/notes 1 2811559 2 bolt, handle mount 2 447224 2 lockwasher, 5/8 internal tooth 3 443828 2 nut, 5/8-18 hex jam 4 4257813 1 handle stop, right side 5 4257814 1 handle stop, left side 6 2809900 1 torsion spring, handle ecl...

  • Page 64: Eclipse

    64 1 2 3 4 37 5 5 6 6 7 8 8 9 9 10 10 10 10 11 12 13 19 20 15 16 16 16 16 17 36 12 4172240 14 18 a b a b a b a b a b 21 gen-set battery 22 23 23 24 24 24 24 25 25 26 26 27 28 28 29 30 31 31 32 33 33 34 35 eclipse 2 4.1 power module mounting plate serial no. All fixed head frame shown. Floating head ...

  • Page 65: Eclipse

    65 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 63305 1 gen-set power module see 19.1 2 63306 1 battery power module see 20.1 3 4253190 2 controller, motor reference u1, u2, see 19.1 4 800271 8 screw, #10-24 x 1/2” pan head 5 404016 2 screw, 1/4-20 ...

  • Page 66: Eclipse

    66 96 db l wa manufactured under one or more of the following u.S. Patents: xxxxxxx xxxxxxx xxxxxxx xxxxxxx xxxxxxx xxxxxxx charlotte, nc year of production: made in u.S.A. ® a textron company 96 db l wa manufactured under one or more of the following u.S. Patents: xxxxxxx xxxxxxx xxxxxxx xxxxxxx xx...

  • Page 67: Eclipse

    67 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 4253156 1 frame, l.H. Side fixed head eclipse 2 118, 122, and 126 1 4253154 1 frame, l.H. Side floating head eclipse 2 118f and 122f 2 4253155 1 frame, r.H. Side fixed head eclipse 2 118, 122, and 126 ...

  • Page 68: Eclipse

    68 1 2 2 3 3 3 3 4 4 5 5 6 6 6 6 7 7 7 7 8 8 9 9 10 10 11 12 13 13 13 14 15 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28 29 30 31 eclipse 2 6.1 lower unit fixed head units serial no. 63334 - all serial no. 63335 - all serial no. 63338 - all serial no. 63339 - all serial no. 63342 - all serial no. 63...

  • Page 69: Eclipse

    69 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 ref 1 reel and bedknife assembly see 7.1 2 400264 2 screw, 3/8-16 x 1-1/4” hex head 3 446142 8 lockwasher, 3/8 heavy 4 400258 6 screw, 3/8-16 x 3/4” hex head 5 3001610 2 block, bedknife adjuster 6 3667...

  • Page 70: Eclipse

    70 optional magknife bedknives part number description 4131005 22” medium section 4131369 22” high profile 4131001 22” low profile 4131370 22” tournament 4131003 22” super tournament standard style bedknives (secured with screws) part number description 5000098 18” low profile ● 5002888 18” super to...

  • Page 71: Eclipse

    71 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 see chart 1 reel 2 4105281 1 bearing housing 3 366650 1 • grease seal 4 545940 1 • bushing 5 500534 1 • bearing cup and cone 6 4179720 1 bearing housing 7 366650 1 • seal 8 545940 1 • bushing 9 500534 ...

  • Page 72: Eclipse

    72 1 2 2 2 3 4 5 5 6 9 6 7 7 8 9 10 11 12 13 14 14 14 15 11 12 13 14 15 16 16 16 17 17 19 19 18 18 8 10 4127335 eclipse 2 8.1 grass shield and roller brackets fixed head units only serial no. 63334 - all serial no. 63335 - all serial no. 63338 - all serial no. 63339 - all serial no. 63342 - all seri...

  • Page 73: Eclipse

    73 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 4139661 1 grass shield, 18 inch used on 63334, 63343, 63335, and 63344 1 4139660 1 grass shield, 22 inch used on 63338, 63347, 63339, and 63348 1 4139662 1 grass shield, 26 inch used on 63342 and 63351...

  • Page 74: Eclipse

    74 4 3 1 2 5 6 7 7 8 8 8 8 9 9 10 10 11 11 12 13 14 15 15 15 15 16 17 18 19 20 21 22 22 23 24 25 25 26 27 29 29 30 30 30 30 31 32 36 37 37 38 35 33 34 34 29 29 30 30 28 28 25 40 eclipse 2 9.1 floating head reel connection floating head units only serial no. 63336 - all serial no. 63337 - all serial ...

  • Page 75: Eclipse

    75 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 4175221 1 rear roller - 18” used on 63336, 63345, 63337, 63346 1 1004990 1 rear roller - 22” used on 63340, 63349, 63341, 63350 2 4175220 1 • shaft, 18” used on 63336, 63345, 63337, 63346 2 3010422 1 •...

  • Page 76: Eclipse

    76 10 12 8 13 11 5 18 14 20 20 27 20 16 17 12 15 12 15 19 9 8 7 4 3 1 2 6 6 21 22 23 24 25 26 28 28 28 4127335 eclipse 2 10.1 outer reel assembly floating head units only serial no. 63336 - all serial no. 63337 - all serial no. 63340 - all serial no. 63341 - all serial no. 63345 - all serial no. 633...

  • Page 77: Eclipse

    77 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 4175221 1 rear roller, 18” used on 63336, 63345, 63337, and 63346 1 1004990 1 rear roller, 22” used on 63340, 63349, 63341, and 63350 2 4175220 1 • shaft, 18” roller used on 63336, 63345, 63337, and 63...

  • Page 78: Eclipse

    78 25 5 24 18 10 1 9 21 8 17 16 17 14 15 4 7 6 12 23 22 26 11 19 28 13 29 27 3 2 20 2 optional magknife bedknives part number description 4131369 22” high profile 4131004 18” super tournament 4131373 18” tournament 4131371 18” low profile 4131001 22” low profile 4131370 22” tournament 4131003 22” su...

  • Page 79: Eclipse

    79 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 4170204 1 frame, 18” reel used on 63336, 63345, 63337, and 63346 1 5002577 1 frame, 22” reel used on 63340, 63349, 63341, and 63350 2 400192 8 screw, 5/16-18 x 1-1/2” hex head 3 446142 1 lockwasher, 3/...

  • Page 80: Eclipse

    80 24 22 21 23 26 27 29 19 17 31 25 25 28 30 2 5 4 6 7 8 1 12 12 13 13 14 10 16 14 3 1 15 15 11 9 18 28 20 19 24 32 eclipse 2 12.1 differential and rollers serial no. All.

  • Page 81: Eclipse

    81 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 1000024 2 18” smooth roller 1 132655 2 22” smooth roller 1 1000027 2 26” dimpled roller 2 366699 1 • differential gear bushing 3 366698 1 • drum bushing 4 366701 1 • grease seal 5 366700 1 • grease sea...

  • Page 82: Eclipse

    82 7 8 1 24 16 16 13 17 25 33 6 4 2 9 5 3 3 18 17 35 35 36 34 28 29 19 32 14 14 22 23 16 16 13 21 20 12 11 12 10 15 15 31 27 30 26 4 eclipse 2 13.1 parking brake and wheels serial no. All.

  • Page 83: Eclipse

    83 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 1000476 1 r.H. Hub 2 338766 1 • bearing 3 366705 2 • grease seal 4 164056 2 brake band 5 132663 1 brake mounting bracket 6 132658 1 seal housing 7 365753 1 • grease seal 8 4128725 1 • grease fitting 9 ...

  • Page 84: Eclipse

    84 8 12 18 18 18 27 31 15 17 17 17 19 19 19 20 20 20 11 13 16 16 21 1 2 3 4 5 6 7 9 14 14 17 22 23 24 25 26 28 29 30 32 32 33 33 10 eclipse 2 14.1 belts and drive motors serial no. All fixed head frame shown. Floating head similar.

  • Page 85: Eclipse

    85 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 446116 2 lockwasher, #10 2 2000148 1 bracket, bearing 3 2811070 1 belt, polychain, 80 tooth 4 2811223 1 pully, 18 tooth 5 2811107 1 pully, 112 tooth 6 3001273 1 shaft 7 4140154 1 floating head pulley c...

  • Page 86: Eclipse

    86 sw1reel switch j14 can diagnostic connector r1 hand throttle potentiometer r2 rotary switch sw2 ignition switch f230 amp fuse j1 and j2 controller connection j6 and j7 reel motor controller connection j10 and j11 reel motor connection j12 and 13 traction motor connection m1 reel motor m2 traction...

  • Page 87: Eclipse

    87 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 4254330 1 harness, main 4262910 1 • 30 amp mini fuse reference f1, see 19.1 2 4253190 1 controller, reel motor reference u1, see 19.1, 4.1 3 4261770 1 motor, brushless bi-directional reference m1, see ...

  • Page 88: Eclipse

    88 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16 17 17 18 19 20 20 21 ® eclipse 2 16.1 genset power source 63305 serial no. 63334 - all serial no. 63335 - all serial no. 63336 - all serial no. 63337 - all serial no. 63337 - all serial no. 63338 - all serial no. 63339 - all serial no. 63340 - all serial ...

  • Page 89: Eclipse

    89 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 4258930 1 engine, honda gx-120 2 320774 1 • key, 3/16 x1-1/2” square 3 4170500 1 trim, muffler 4 4172080 1 valve, oil drain 5 4187840 1 gasket, oil drain valve 6 4253595 1 mount, power source 7 441977 ...

  • Page 90: Eclipse

    90 1 2 2 2 3 3 3 3 4 4 5 5 6 7 8 9 10 11 12 13 14 eclipse 2 17.1 battery power source 63306 serial no. 63343 - all serial no. 63344 - all serial no. 63345 - all serial no. 63346 - all serial no. 63347 - all serial no. 63348 - all serial no. 63349 - all serial no. 63350 - all serial no. 63341 - all.

  • Page 91: Eclipse

    91 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 1 2809837 2 spring, extension 2 444708 6 locknut, 1/4-20 center 3 443102 8 nut, 1/4-20 hex 4 446130 4 lockwasher, 1/4 heavy 5 441604 4 carriage bolt, 1/4-20 x 1” 6 400108 2 screw, 1/4-20 x 3/4 hex head 7...

  • Page 92: Eclipse

    92 battery post style terminal hardware 8 10 10 to battery gauge 10 10 10 10 12 22 11 23 21 13 14 15 26 27 24 6 6 18 19 20 20 16 17 25 p n key battery and battery monitor connections 7 9 9 9 9 14 see above 7 4170001 stop 2 5 4 1 6 6 3 a a eclipse 2 18.1 battery case serial no. All.

  • Page 93: Eclipse

    93 > change from previous revision eclipse 2 item part no. Qty. Description serial numbers/notes 68668 1 battery case does not include batteries 1 4105660 1 • screw, 5/16-18 x 1-1/4” nylon 2 452004 2 • flat, washer 1/4 3 4105800 1 • fuse, 50a reference f1, see 19.1 4 447214 1 • lockwasher, 5/16 inte...

  • Page 94: Eclipse

    94 run start off e f d a j2-25 j24 j22 j23- – j23- + j23- – j23- + p n key j2-24 red wht/red j2-15 j2-16 j2-29 b wht/red red sw2 key switch gc1 yel on off sw1 mow switch r3 5 Ω resistor r2 bail potentiometer r1 throttle potentiometer sw3 engine on/off switch t1 ignition coil e1 spark plug f1 50a b1 ...

  • Page 95: Eclipse

    95 u2 traction motor controller u1 reel motor controller m1 reel motor red blk shld sw4 light switch l1 work light optional work light kit on off blk grn blu wht red brn grn blu wht red brn grn blu wht red brn grn blu wht red brn blk red red red blk yel blk j6-8 j6-9 j6-10 j14-c j14-b j14-a +48v inp...

  • Page 96: Eclipse

    96 eclipse 2 item reference illustration part number description serial numbers/notes b1 see 18.1 n/s 12 volt sla battery obtain batteries localy or through your jacobsen dealer battery power module only b2 see 18.1 n/s 12 volt sla battery b3 see 18.1 n/s 12 volt sla battery b4 see 18.1 n/s 12 volt ...

  • Page 97: Fluids and Compounds

    Fluids and compounds * refer to the operator’s manual or the parts & maintenance manual for the correct hydraulic oil requirements for your machine. Jacobsen offers a high usage parts catalog illustrating commonly used parts through easy to read line drawings. See your local jacobsen dealer for a co...

  • Page 98: Index

    98 index 1000024.......................81 1000027.......................81 1000476.......................83 1000477.......................83 1000480.......................79 1002224.......................77 1004756.......................79 1004990.................75 , 77 132655.........................

  • Page 99: Index

    99 index 4203300...................... 75 4208861...................... 96 4223946...................... 71 422504 ........................ 61 4225502...................... 71 4225504...................... 79 4225505...................... 79 4234900...................... 79 4234901................ 7...

  • Page 100

    Jacobsen, a textron company 11108 quality drive, charlotte, nc 28273 www.Jacobsen.Com 800-848-1636 when performance matters. ™ equipment from jacobsen is built to exacting standards ensured by iso 9001 and iso 14001 registration at all of our manufacturing locations. A worldwide dealer network and f...