Jacobsen Groom Master II Safety & Operation Manual - Warning

Summary of Groom Master II

  • Page 1

    Warning:if incorrectly used, this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the entire manual before attempting to set up, operate, adjust or service the machine. Gb safety & operation manual wh...

  • Page 2

    1 contents en-2 proposition 65 warning engine exhaust from this product contains chemicals known to the state of california to cause cancer, birth defects, and other reproductive harm © copyright 2010, jacobsen, a textron company. “all rights reserved, including the right to reproduce this book or p...

  • Page 3: Warning

    Safety 2 en-3 2 safety 2.1 operating safety ______________________________________________________ 1. Safety is dependent upon the awareness, concern, and prudence of those who operate or service the equipment. Never allow minors to operate any equipment. 2. It is your responsibility to read this ma...

  • Page 4: Warning

    2 safety en-4 2.2 important safety notes________________________________________________ this safety alert symbol is used to alert you to potential hazards. Danger - indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning - indicates a poten...

  • Page 5

    Decals 3 en-5 3 decals 3.1 decals _________________________________________________________________ familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. 4181865 4181864 • read operator's manual. Do not allow untra...

  • Page 6

    3 decals en-6 familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. 700877 4199140 4164281 4181860 warning to prevent burns, do not touch muffler or muffler shield. Temperatures may exceed 150° f (66° c). Warning p...

  • Page 7

    Decals 3 en-7 4181863 838368 4135931 3008577 3002308 838363 3008576 838364 warning (gas units only) stop engine before engaging or disengaging belt ider. Engaging idler while engine is running may cause vehicle to move in either forward or reverse direction without warning and may result in personal...

  • Page 8: Caution

    4 initial inspection en-8 4 initial inspection 4.1 general________________________________________________________________ the inspection and testing of the unit should always be performed by a trained technician, familiar with the operation of this equipment. Read each instruction completely and ma...

  • Page 9: Warning

    Controls 5 en-9 5 controls 5.1 icons ___________________________________________________________________ warning never attempt to drive the unit unless you have read the safety and operation manual and know how to operate all controls correctly. Familiarize yourself with the icons shown above and wh...

  • Page 10

    5 controls en-10 a b c d e f g h j l k l m n p r b 1 b 2 s total hours 1 10 0 0 0 0 0 a steering tilt lever b parking brake c traction pedal d rake control lever e scarifier control lever (optional) f blade control lever (optional) g throttle h seat adjuster j fuel cap k access panel l tool holder m...

  • Page 11: Caution

    Controls 5 en-11 5.2 control descriptions __________________________________________________ a. Steering tilt control pull lever to release steering column. Tilt column up or down to position desired. Release lever to lock steering column in place. B. Parking brake lock / release to lock parking bra...

  • Page 12

    5 controls en-12 5.3 operator alerts_______________________________________________________ the electronic controller monitors vital machine systems. It uses an audible alarm and warning lights to alert the operator of conditions requiring immediate action. When an alert occurs follow the general gu...

  • Page 13: Caution

    Operation 6 en-13 6 operation 6.1 daily inspection ________________________________________________________ 1. Perform a visual inspection of the entire unit, look for signs of wear, loose hardware, and missing or damaged components. Check for fuel or oil leaks to ensure connections are tight and ho...

  • Page 14: Warning

    6 operation en-14 6.3 operating procedures_________________________________________________ 1. Under no circumstances should the engine be started without the operator seated on the unit. 2. Never run the engine in an enclosed area. 3. Keep hands and feet away from moving parts. If possible, do not ...

  • Page 15: Warning

    Operation 6 en-15 6.4 starting________________________________________________________________ important: do not use starting assist fluids. Use of such fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition and could result in serious engine damage. 1. Ma...

  • Page 16: Caution

    6 operation en-16 6.6 to drive / transport____________________________________________________ read and follow all safety notes contained in this manual when driving or transporting unit. Refer to section 6.3 for general operating instructions. When operating in reverse look behind you to ensure you...

  • Page 17

    Operation 6 en-17 how to calculate a slope: tools required: level (a), either 1 yard, or 1 meter long. Tape measure (b). With the level (a) positioned horizontally, measure the distance (c) with tape measure (b). Use the chart to calculate eirther the slope angle or the % grade of the slope (d). Fig...

  • Page 18

    6 operation en-18 6.8 attachments ___________________________________________________________ the groom master will accept several attachments designed to perform a variety of operations. Before installing and using attachments read and save the instruction sheet included with it. Contact your jacob...

  • Page 19: Warning

    Operation 6 en-19 6.11 daily maintenance______________________________________________________ important: for more detailed maintenance information, adjustments, and maintenance/lubrication charts, see the parts & maintenance manual. 1. Park the unit on a flat, level surface. Fully lower the attachm...

  • Page 20: Warning

    6 operation en-20 6.12 long term storage ____________________________________________________ general 1. Wash the unit thoroughly and lubricate. Repair and paint damaged or exposed metal. 2. Inspect the unit, tighten all hardware, and replace worn or damaged components. 3. Drain and refill radiator....

  • Page 21

    Notes 7 en-21 7 notes.

  • Page 24

    World class quality, performance and support equipment from jacobsen is built to exacting standards ensured by iso 9001 and iso 14001 registration at all of our manufacturing locations. A worldwide dealer network and factory trained technicians backed by genuine parts provide reliable, high-quality ...