Operator's manual cleaning system high pressure cleaning machines mod. 6500 mod. 6500 stop total mod. 6800 mod. 6800 stop total 11/2005 - 469825 - mi-0305 exclusive for domestic application mÁquinas agrÍcolas jacto s.A. - jacto cleaning av. Perimetral, 901 - distrito industrial cep: 17580-000 - pomp...
Table of contents models ............................................................................................. 04 introduction .................................................................................. 05 important information to the user ....................................... 06 pr...
Models functional features and identification of the equipment the operation of the motor with the gun (water outlet) in closed position is the only difference among these models. Models 6500 / 6800 - with the gun in closed position, the motor continues to run normally, causing the water circulate i...
Introduction the jacto high pressure cleaning machines were designed to clean, remove the grease of parts, agricultural machinery, vehicles, etc; remove dirts from metallic structures and other applications that require high pressure jets assisted by detergents and removers. It is available with 110...
Important information to the user before using the jacto high pressure cleaning machines, read carefully and follow strictly the instructions given herein. You must maintain all the decals in the right place and replace any of them if illegible. Mind your work to prevent any possibility of personal ...
Important information on the use - never switch on the machine without supply of water or solution. - in switching off the machine, pull the gun trigger to discharge the pressure remaining in the system. - always use shoes with soles made of rubber or other insulating material. - the models jacto 65...
Important information - do not allow children and untrained people to use this machine. - never point the gun towards persons or animals since the high pressure jet can injure them. - never point the gun towards electric equipment or thin surface. 08 - never point the gun towards the machine. - be c...
Important information attention - in case of fire, never point the jet towards e l e c t r i c equipment or the power supply circuit. - for the machines 6500 and 6800 stop total, it is always necessary to note the on/off switch before pulling the gun, because the machine can be on and the system cha...
Identification plate on the lower part of the hood there is a plate containing information on the machine model, serial number, working pressure, motor voltage and other important data. For warranty claim, it is necessary to specify data from the identification plate, mainly the serial number (1), f...
Note: fluctuations on the pressure and flow rate of up to 20% are normal. Technical specifications high presure cleaning machine 6500 / 6800 maximum flow rate (l/h) ........................... Maximum pressure (psi) .......................... Voltage (v) ................................................
Trolley assembly - model 6500 high pressure machines - models 6500 a b c a- trolley asembly 12 fastening screw m5 x 30 necessary components to assemble the tolley: - 1 plastic handle; - 1 metallic rod; - 2 wheels; - 2 caps; - 1 support; - 1 axle; - 4 screws m5 x 30; - 2 nuts m5; - 6 locks. Fastening...
C- support assembly trolley assembly - model 6500 b- axle and wheel assembly 13 operation using additives always use product with neutral ph in the dispenser. Attach the dispenser to the extension end. Note: it is not necessary to screw or fasten the dispenser; just fit the extension end into its co...
Trolley assembly - model 6800 high pressure machines - models 6800 - mount the trolley arms as shown in the figure below. Main handle fastening screw intermediate handle electric cable fastening screw high pressure hose right rod (see letter d embossed) left rod (see letter e embossed) 14 operation ...
Water supply direct from the water tap use reinforced hose with minimum nominal diameter of 1/2" (13 mm). From a tank - before starting the cleaning, fill the suction hose with water or solution to eliminate the air in the hose and in the pump head. - it can be necessary to attach a non-return valve...
Power supply cable with ground plug the equipment is assembled with a 3-prong ground plug, the round prong of which is connected to the pump body. So when this plug is connected to the socket, the pump body will be also connected to the ground wire of the power supply circuit. The job of the ground ...
