1. DL manuals
  2. Jacuzzi
  3. Bathroom Aid
  4. J-DREAM
  5. Owner's Manual

Jacuzzi J-DREAM Owner's Manual

Manual is about: J-DREAM Shower System

Summary of J-DREAM

  • Page 1

    Whirlpool bath r j-dream ™ shower system owner’s manual assembly, installation & operating instructions.

  • Page 2: Owner’S Record

    Important safety information read all installation instructions save these instructions for future use. Date purchased purchased from installed by serial number model # (see page 3 for location of serial number.) owner’s record jacuzzi whirlpool bath does not recommend prolonged periods of use of th...

  • Page 3: Contents

    Contents 1 part i assembly and installation ____________________________________________ 2–27 specifications _____________________________________________________________________________ 2 general assembly information ______________________________________________________________ 3–4 j-dream packagi...

  • Page 4: J-Dream

    J-dream ™ owner’s manual dimensions 60" ( 1524 mm) l 36" (914.4 mm) w 81" ( 2057 mm) h product specifications are subject to change without notice. Specifications part i: assembly and installation 2 front view 60" (1524 mm) (right hand shown) 3" (76 mm) clearance to remove dome 83" (2108mm) 81" (208...

  • Page 5: J-Dream

    Read all instructions before beginning assembly and installation general assembly information the j-dream shower unit is installed either into a niche or a corner with the drain at the side of the unit as you face the shower door. This manual explains the step by step procedures for assembly, instal...

  • Page 6: J-Dream

    J-dream ™ owner’s manual 4 electrical requirements your j-dream, as it comes from the factory, requires a gfci protected 240 vac 3- wire 20 amp 50-60 hz circuit (2 conductor with ground) for single (1) phase electrical service, and must be in a separate circuit having no other appliance connected in...

  • Page 7: J-Dream

    J-dream ™ owner’s manual hardware identification chart 5 circled letters a are used in the illustrations of the assembly procedure. Nut j 1/4-20 lock nut pan head screw #10-24 x 3/4 screw b flat washer 1/4 c washer lock nut 10-24 nut d flat head screw m4x10mm screw e pan head screw #12 x 1/2 screw f...

  • Page 8: J-Dream

    J-dream ™ owner’s manual rough-in corner (left hand) washing machine outlet box connect #8 gauge (10 mm 2 ) minimum solid copper bond wire to house electrical panel or approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate electrode, or other acc...

  • Page 9: J-Dream

    J-dream ™ owner’s manual rough-in corner (right hand) 7 washing machine outlet box connect #8 gauge (10mm 2 ) minimum solid copper bond wire to house electrical panel or approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate electrode, or other a...

  • Page 10: J-Dream

    J-dream ™ owner’s manual rough-in niche (left hand) 8 16" finished walls 2" waste stubout finished wall surface finished floor material 60" finished minimum finished wall surface 36" washing machine outlet box connect #8 guage (10mm 2 ) minimum solid copper bond wire to house electrical panel or app...

  • Page 11: J-Dream

    J-dream ™ owner’s manual rough-in niche (right hand) 9 16" finished walls 2 " waste stubout finished wall surface finished floor material 60" finished minimum finished wall surface 36" washing machine outlet box connect #8 gauge (10 mm 2 ) minimum solid copper bond wire to house electrical panel or ...

  • Page 12: J-Dream

    J-dream ™ owner’s manual base and drain important: locate base to provide assembly access to all sides remove base from carton labeled base/top. Place clear top in carton to prevent damage. The clear top will not be installed until the unit has been fully assembled and plumbed. Position the j-dream ...

  • Page 13: J-Dream

    Broken line represents drain stub assembly tool locking ring rubber compression sleeve screwdriver tighten locking ring clockwise wall drain compression fitting temporary wood block drain assembly floor drain stubout flush with, or beneath floor surface j-dream ™ owner’s manual drain fitting after t...

  • Page 14: J-Dream

    J-dream ™ owner’s manual 12 installation of panels (note: right hand j-dream ™ with stereo shown throughout this manual except where noted.) attach seat wall to base bolts (8) nuts (8) g j align four holes on seat wall frame over base and insert bolts and tighten nuts from underneath. Washers (8) i ...

  • Page 15: J-Dream

    J-dream ™ owner’s manual attach panel #2 to seat wall frame slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. F screw (4) c washer (4) top view move f...

  • Page 16: J-Dream

    J-dream ™ owner’s manual install back wall caulk the bottom and sides of back wall where indicated in the illustrations below. Install fasteners. Now align the back wall parallel to the pan lip to center the back wall between the seat wall and the end panel. Screw (4) b washer (8) c nut (4) d caulk ...

  • Page 17: J-Dream

    J-dream ™ owner’s manual attach panel #1 to seat wall remove 4 bolts from seat wall to attach panel # 1 to seat wall. Caulk along surface of seat wall. 15 panel #1 reinstall bolts (4) and washers (4) removed from seat wall and bracket seat wall attaches to panel #1 two places. Caulk seat wall attach...

  • Page 18: J-Dream

    J-dream ™ owner’s manual attach front panel bracket to seat wall frame and t bracket to front panel bracket. Attach panel support and spacer bracket to base frame and l bracket to panel support to p o f frame 58-3/8" 17" for clarity panel #1 not shown in this illustration. G hex bolt (2) this bolt g...

  • Page 19: J-Dream

    Attach angle bracket to panel #1 note that the angle bracket has a notch on the top and bottom. This notch does not get screwed against the side panels but faces out as shown in the side view. Do not tighten the screws at this time as the angle bracket will have to be aligned with the door frame hol...

  • Page 20: J-Dream

    J-dream ™ owner’s manual 18 attach end panel note: end panel is glass for corner version and color-matched acrylic for niche version. Remove the screw located on the bottom left side of the end panel (illustration a). Attach the bracket to the end panel using this screw. Lift the end panel onto the ...

  • Page 21: J-Dream

    J-dream ™ owner’s manual attach door frame to angle brackets and base frame before proceeding, make sure the seat wall is closed and fastened. Align door frame over tabs on base frame and pan lip. The pan lip is to fit into corner posts of the door frame. Align holes along sides of door frame with a...

  • Page 22: J-Dream

    J-dream ™ owner’s manual attach top frame to door frame, end panel assembly, back wall, and seat wall frames press/tap top frame into door frame and end panel frame, aligning notch in door frame with corner of top of frame while aligning with corners of enclosure (illustration a). Frame snaps down i...

  • Page 23: J-Dream

    J-dream ™ owner’s manual attach hoses for hot and cold water lines and control cable feed the hot and cold water supply lines to the mixer valve and connect as shown. Feed the valve manifold supply line and valve #4 line from the equipment seat wall and connect as below. Route the water filter line ...

  • Page 24: J-Dream

    J-dream ™ owner’s manual 22 right seat wall (equipment wall) connect the hoses routed from the back wall as below (grayed lines are pre-attached). Connect the controller line. Connect the two steampro power cords after unraveling them. Before using the steampro generators, disconnect copper lines an...

  • Page 25: J-Dream

    J-dream ™ owner’s manual bonding connect #8 gauge (10 mm 2 ) minimum solid copper bond wire to house electrical panel or approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate electrode, or other acceptable bond. Check your local building code fo...

  • Page 26: J-Dream

    J-dream ™ owner’s manual 24 1. Make sure electric power is off at main breaker. 2. Disconnect the lines from the outlet side of the filters. Turn the water supply on and run water through the filters to flush out any blackish carbon fines. Turn water supply off and reconnect the lines. When tighteni...

  • Page 27: J-Dream

    J-dream ™ owner’s manual attach front panels to unit attach front panels with pre-installed velcro®. Install 2 screws through the top of the panel (illustration a). Connect the cd/radio ground wire, speaker/power connector and antenna wire before installing left front panel (illustration b). Ground ...

  • Page 28: J-Dream

    J-dream ™ owner’s manual place top cover place the clear cover on top of the unit. Align notch in cover with the corresponding notch in the top metal frame. 26.

  • Page 29: J-Dream

    J-dream ™ owner’s manual test for leaks and attach side and bottom panels turn on electric power at main breaker. Operate the unit and check for leaks. Attach side and bottom panels. Take the bottom panel at an angle and insert under the bottom of the enclosure frame. Rotate backwards till it is up ...

  • Page 30

    28 figure 1. Control panel and display figure 2. Mixer control part ii: operating instructions control panel system control is provided by the electronic display located inside the shower cabin (see figure 1) the display is used to start up the five functions of the unit: the shower, the cascade wat...

  • Page 31: Part III Maintenance

    29 starting the hydromassage the j-dream allows you to enjoy the benefits of a real hydromassage. The hydromassage is created by the combined action of 8 water jets (2 sets of 4 ). The action of each group of jets is either alternated or pulsed. To start the hydromassage jets, press the jets button ...

  • Page 32

    30 care and maintenance of steampro generators the steam generator tanks must be drained after each 60 hours of operating time. To drain the units: 1. Turn off power to the unit. 2. To gain access to the steampro generators, the seat wall (equipment wall) must be swung open. To do so, remove the thr...

  • Page 33

    31 troubleshooting chart 1. Control is on and appears to be functioning, but no steam. A. Allow 2 minutes for steam to flow. B. Replace water filter, drain and flush out steamer and steam plumbing. Pour six ounces of water into the steam delivery tube. Reset high limit safety switch. A. Replace wate...

  • Page 34

    Service access the j-dream seat wall is hinged at the back wall to allow the seat wall to be swung open for service access to equipment behind and on the seat wall. Make sure the power is off at the main breaker. Remove the top cover. Remove the front panel next. To do this, remove 3 screws securing...

  • Page 35

    Remove screws (3 places) remove 2 bolts (2 places) panel #1 service access (continued) remove 3 screws along the door frame post. Then remove 4 hex head bolts along the seat wall. Swing seat wall with panel 1 toward back wall. To reassemble, reverse these procedures. 33.

  • Page 36

    Printed in the u.S.A. Printed on recycled paper product specifications are subject to change without notice. Use installation instructions supplied with product. ©1997 jacuzzi whirlpool bath m347000 b 3/01 jacuzzi whirlpool bath national headquarters p.O. Drawer j, walnut creek, ca 94596 (925) 938-7...