Summary of THE SANTINA
Page 1
Portable whirlpool spa owner's manual whirlpool bath r the santina ™.
Page 2: Owner'S Record
Date purchased purchased from installed by spa serial number model #d550000 (see page 2 for location of serial number.) save these instructions for future use. Owner's record important safety information read and follow all installation instructions jacuzzi whirlpool bath does not recommend spa wate...
Page 3: The Santina
1 the santina ™ portable whirlpool spa owner's manual model d550000 contents page installation instructions ___________________________________ 3-6 inspection and shipping claim _______________________________ 3 unpacking _______________________________________________ 3 positioning your spa _______...
Page 4: The Santina
Specifications model electrical requirements 829 lbs. (377kg) shipping weight electric heater 6 kw 26 amps operating gallonage 325 u.S. Gal. (1230 ltrs.) product weight 595 lbs.. (270 kg) dimensions 84" (2134. Mm) l. 84" (2134. Mm)w. 36" (914. Mm) h. Product specifications are subject to change with...
Page 5: Installation Instructions
Unpacking 1. Read disclaimer for shipping damages on side of crate. 2. Remove sides and top of crate, as well as plastic bags, leaving pallet intact. 3. Check for shipping damage. 4. Remove and set aside unattached accessory pieces. 5. Move spa to final site with pallet still attached as shown. 6. P...
Page 6: Installation
Because your santina spa is portable, you can locate it just about anywhere you wish—on a deck, patio, or even indoors. Be sure to position it above ground in an area with good drainage and on a level, continuous surface which can support the weight of the spa when filled with water and people; this...
Page 7: Installation
5 support and drainage outdoor installations if you install the spa outdoors, we recommend that you provide a concrete pad for it to rest on. To do this, construct forms for an 8' x 8' x 4" thick level pad. Install a #10 gauge wire mesh 6" x 6" steel reinforced grid. Attach a #8 solid copper wire to...
Page 8: Installation
6 installation equipment set-up • turn on circuit breakers at the main electrical panel. • select jets on the system switch. • add 1 / 4 cup sodium dichlor (a fast dissolving granu- lar type of chlorine) to the water and let the whirlpool run for 15-20 minutes only. • turn off jets. • turn off circu...
Page 9: Operating Instructions
Operating instructions now that your santina spa is in place, you are probably eager to take advantage of its unique designed-in features— especially the patented jacuzzi whirlpool bath hydromassage performance. Besides being a beautiful addition to your indoor decor or outdoor landscaping, your jac...
Page 10: Operation
Make sure the circuit breaker buttons are pushed in. Locate the high temperature safety switch, which is a raised button on the end of the heater. Push this button to be sure it is in the reset mode. The purpose of this switch is to shut down the spa if the water becomes excessively hot. If, for som...
Page 11: Operation
Operation controls the contrtol panel giving you convenient control of the jets, filter, heater/filter, blower and light is located on the spa rim. To ensure your safety and allow easy operation, your spa is equipped with two air-activated switches. One, the system switch, controls the whirlpool jet...
Page 12: Operation
Operation heater control turn on the heater by selecting the htr/fltr mode on the system selector switch. With this selection, you can verify that the spa’s heater is operating by viewing the heater indicator light on the spa control panel. Set the heater control knob by rotating it to the desired t...
Page 13: Operation
Normal operation/whirlpool system you can enjoy the santina spa with or without activating the whirlpool. Either way, bathing in your spa can be pleasurable, as well as therapeutic. After a busy, stressful day, you can look forward to soaking in your spa in still water with no turbulence—only the ge...
Page 14: Maintenance
Filtration the filtration system of your spa will keep your water clear and clean if used properly. We recommend that you run your filter system for at least two hours each day. The filter cartridge elements will trap most solid materials and debris in the water. However, the presence of materials s...
Page 15: Water Chemistry
Water quality definitions it often tends to form calcium deposits on heater parts and plumbing fittings and leaves an unattractive film on the spa at the water line. Sodium hypochlorite: a liquid chlorine product that is inexpensive and effective but not recommended because the liquid is readily spi...
Page 16: Maintenance
Water level/drain the water level in the spa must be maintained at its normal level. Evaporation and splashing will cause the water level to drop. When concentrations of impurities from evaporation, water quality chemicals, body oils, perfumes, dirty feet, and winds, etc., accumulate in the spa and ...
Page 17: Maintenance
Winterizing in a climate where winter temperatures are below freezing, follow this procedure when the spa will not be used: 1. Select the off mode. 2. Turn off the power at the circuit breaker. 3. Drain the spa completely by attaching a garden hose to the drain valve on the suction plumbing. Then re...
Page 18: Cleaning Your Spa
Spa light two filters, one blue and one red, are provided with your spa. To change the filter, simply snap the colored filters in place on top of the normal lens. Two replacement bulbs (ge model 912, 12w, 12v) are also included. Put them in a safe place for future use. When a bulb burns out, replace...
Page 19: Troubleshooting Guide
* note: the skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your jacuzzi whirlpool bath authorized service agent or dealer. Problem remedy probable cause a. Turn on circuit breakers. Reset gfci. B. Wait 60 seconds, system will b...
Page 20: Troubleshooting Guide
6. Low water flow from jets. (continued) 7. No water flow from jets. Remedy probable cause problem a. Worn or damaged pump seal. A. Power off. B. Off mode selected. C. House circuit breaker tripped or in off position. D. Spa circuit protectors tripped. E. Gfci tripped. F. High temperature safety swi...
Page 21: Troubleshooting Guide
* note: the skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your jacuzzi whirlpool bath authorized service agent or dealer. Remedy probable cause problem g. Call and electrician or your power company. H. * i. * j. * k. * a. Let ...
Page 22
Alternate use of water rainbow spout as fill spout you can use your water rainbow spout as a fill spout by permanently plumbing it to a fresh water supply as local codes permit. Local plumbing codes may require the use of an anti-siphon valve for such connection. Do not interconnect water supply wit...
Page 23
Jacuzzi whirlpool bath national headquarters p.O. Drawer j, walnut creek, ca 94596 (510) 938-7070 service support: call (800) 288-4002 jacuzzi whirlpool bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility ...