Jandy Pro Series Installation Manual - Warning
Page 7
English
Jandy
®
Pro Series, WaterColors LED Lights
|
Installation Manual
5.
The wet niche must be properly electrically
bonded and grounded via the No. 8 AWG ground
connector located at the rear of the niche. See
Figure 1.
To be certain that the pool’s electrical system meets
all applicable requirements, the electrician should also
consult the local building department.
4.2 Replacing the light Fixture
nOTE
Performthesestepsonlyaftertheelectricalsystem
requirementsaremet.
WARning
Failuretobringthepool’selectricalsystemuptocode
requirementsbeforeinstallingtheunderwaterlight
willcreateanelectricalhazardwhichcouldresultin
deathorseriousinjurytopoolorspausers,installers,
orothersduetoelectricalshock,andmayalsocause
damagetoproperty.
nOTE
Thelightfixturemaybereplacedwithoutremoving
waterfromthepool.
1.
Turn off the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
2.
Unscrew the special pilot screw at top of the
face ring and remove the light assembly from the
niche, and place the assembly on the deck.
WARning
Besuretokeepthespecialpilotscrewprovided
withthisunderwaterlight.Thisscrewmountsand
electricallygroundsthehousingsecurelytothe
mountingringandwetniche.Failuretousethescrew
providedcouldcreateanelectricalhazard,whichcould
resultindeathorseriousinjurytopoolorspausers,
installersorothersduetoelectricalshock.
3.
Remove Junction Box cover, disconnect the light
fixture wires and strain relief, and then pull the
cord out of the conduit from the niche.
4.
Feed the new light fixture cord through the
conduit from the niche to the Junction Box.
nOTE
Dependingonthelengthoftheconduit,specialtools
mayberequiredtopullthecordthroughtheconduit.
5.
Leave at least four (4) feet of cord to coil around
the light fixture or coiled into the base of the light
niche, see Figure 1. This allows the light to be
serviced after the pool is filled with water.
6.
Cut the cord at the Junction Box, leaving at least
six (6) inches of cord to make connections.
7.
Strip six (6) inches of the outer cord jacket from
the cord to expose the three insulated wires. Be
careful not to damage the insulation on the three
(3) inner wires.
8.
Install the strain relief over the cord jacket and
connect all three wires to the corresponding
circuit wires in the junction box. Install the
junction box cover.
9.
Reinstall the light assembly into the niche and
tighten the special pilot screw.
WARning
Useonlythespecialpilotscrewprovidedwiththis
underwaterlight.Thisscrewmountsandelectrically
groundsthehousingsecurelytothemountingring
andwetniche.Failuretousethescrewprovidedcould
createanelectricalhazard,whichcouldresultindeath
orseriousinjurytopoolorspausers,installersor
othersduetoelectricalshock.
10. Fill the pool until the underwater light is
completely submerged in water before operating
the light for more than 10 seconds. Turn on main
switch or circuit breaker, as well as the switch,
which operates the underwater light, to check for
proper operation. Refer to Section 6, Operating
Instructions.
WARning
Neveroperatethisunderwaterlightformorethan
10secondsunlessitistotallysubmergedinwater.
Withouttotalsubmersion,thelightassemblywillget
extremelyhot,whichmayresultinseriousburnsorin
breakageofthebulborlens.Thismayresultinserious
injurytopoolorspausers,installers,orbystandersor
indamagetoproperty.