Jandy Pro Series Installation Manual - Controlling Jandy Pro
Page 8
English
Jandy
®
Pro Series, WaterColors LED Lights
|
Installation Manual
section 5. Wiring Options for
Controlling Jandy Pro
series WaterColors lED
lights
nOTE
The
Jandy Pro series WaterColors lightswillnot
operateproperlywithlightdimmers.Do not wire the
Jandy Pro Series Lights to any dimming circuitry.
To the extent allowed by code and capacity of the
electrical equipment, multiple Jandy Pro Series lights
may be controlled with a single switch so their colors will
always be synchronized.
Separate switches may be used to control the on/off
and color functions of each Jandy Pro Series light. It is
recommended that these switches be located next to each
other to facilitate simple color synchronization when
desired. All switches must be operated at the same time
to assure color synchronization. Otherwise, the lights will
work independently of each other.
5.1 Wiring to an Aqualink
®
Rs Control
system
The Jandy Pro Series WaterColors Lights can be wired
into the Jandy Pro Series AquaLink RS control system
to provide simplified operation of the lights, as well as a
means to synchronize the color change function. Connect
the lights to one of the auxiliary relays in the Power
Center.
nOTE
Itisrecommendedtoconnectonelightperrelayso
eachlightcanbecontrolledseparately.However,upto
fourlightscanbeconnectedonasinglerelay.Ifthere
aremorethanfourlightsinstalledononeAquaLinkRS
system,ensurethereismorethanoneauxiliaryrelay
availableinthePowerCenter.
Refer to Figures 2 and 3 to connect the Jandy Pro Series
Color Lights to the Power Center.
CAUTiOn
AGroundFaultCircuitInterrupter(GFCI)mustbe
providedfor120voltmodels.Theconductorsonthe
loadsideoftheGFCIcircuitshallnotoccupyconduit,
boxes,orenclosurescontainingotherconductors
unlesstheadditionalconductorsarealsoprotectedby
aGFCI.Refertolocalcodesforcompletedetails.
nOTE
TheJandyProSeriesWaterColorsLightsareavailable
in120-voltand12-voltversions.Ifinstallinga12-volt
light,a120-volt/12-voltstep-down(AC)transformer
mustbeused.Formoreinformationabout12-volt
installations,refertoSection 8ofthismanual.
5.2 Wiring to a Time Clock
The Jandy Pro Series WaterColors Lights can be wired
into a basic time clock to automatically turn on the lights
at a predesignated time. Refer to Figure 4 to connect the
lights into the time clock.
5.3 Wiring to a switch
The Jandy Pro Series WaterColors Lights can be wired
into a switch to manually turn on/off the lights. Refer to
Figure 5 to connect the lights into the switch.
section 6. Jandy Pro series
WaterColors lED light
Operating instructions
6.1 To Operate the light and Change
Colors
Turn the light ON. The first time the light is turned on,
the color sequence begins with the Alpine White. To
change the color, turn the light OFF and then ON within
three (3) seconds. Continue turning OFF and ON until
the desired light color mode is reached. See Table 1 for
the color mode sequence.
Table 1.
Jandy Pro series WaterColors lights
sequence
sequence Order
Color Modes
1
AlpineWhite
2
SkyBlue
3
CobaltBlue
4
CaribbeanBlue
5
SpringGreen
6
EmeraldGreen
7
EmeraldRose
8
Magenta
9
Violet
10
SlowColorSplash
11
FastColorSplash
12
AmericatheBeautiful
13
FatTuesday
14
DiscoTech
nOTE
WhenthelightisturnedOFFformorethanseven(7)
seconds,itwillremaininthecolorsetthatiscurrently
active.WhenthelightisturnedbackON,thelightwill
beonthesamecolorset.