1. DL manuals
  2. Jasco
  3. Lighting Equipment
  4. ZW3103
  5. User manual

Jasco ZW3103 User manual

Manual is about: Wireless Lighting Control On/Off/Dim Lamp Module

Summary of ZW3103

  • Page 1

    Wireless lighting control on/off/dim lamp module z-wave ® certified wireless lighting control 45702 zw3103 made in china.

  • Page 2: Introduction:

    Introduction: thank you for your purchase of a jasco z-wave ® control device. Z-wave ® technology is designed to automate lighting/home control and provide easy remote operation of all your z-wave ® enabled devices. The jasco z-wave ® product family includes a variety of devices to control lighting ...

  • Page 3

    Manual/program button standard ac outlet z-wave outlet (other end) the lighting load plugged into the z-wave ® controlled outlet on this module must not exceed 300 watts incandescent. This module has been optimized for use with incandescent lighting as well as with most dimmable cfl and led bulbs. N...

  • Page 4: Risk of Fire

    There are no user serviceable parts in this unit. To reduce the risk of electric shock, this product has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type power outlet. If the plug does not fit into the outlet, contact a qualified electrician to in...

  • Page 5: Wireless Range

    Wireless range this device complies with the z-wave standard of open- air, line of sight transmission distances of 65 feet. Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type of construction and the number of z-wave enabled ...

  • Page 6: Z-Wave Enabled Devices.

    Effects of home construction on wireless range between z-wave enabled devices. Note: the distances shown in the table below are typical examples. Actual performance in your home will vary. From the remote (or repeating z-wave module) to destination device: * for plug-in modules or in-wall devices in...

  • Page 7: Key Features:

    Please note: z-wave home control networks are designed to work properly alongside 802.11 wireless computer networks, bluetooth and other 2.4ghz or 5.8ghz devices. Some baby cams, wireless video devices and older cordless phones using the 900mhz frequency range may cause interference and limit z-wave...

  • Page 8: Basic Operation

    Basic operation the connected light can be turned on in three ways: 1. With a z-wave remote. 2. Manually with the pushbutton on the z-wave module. 3. By the load-sensing feature. Normally, the z-wave module controls the on/off state of the connected light and power is either turned on or off at the ...

  • Page 9: On/off/dim State.

    2. Adjust the brightness level of the connected lighting by pressing and holding the button. Release the button when the desired level is attained. - this is also a toggle function. The lighting will dim until the minimum level is attained or the button is released. The next time the button is press...

  • Page 10: All On/all Off

    All on/all off depending upon your primary controller, the 45702 lamp module can be set to respond to all on and all off commands in up to four different ways. Some controllers may not be able to change the response from its default setting. Please refer to your controller’s instructions for informa...

  • Page 11: Dim Rate Adjustments

    Dim rate adjustments both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means t...

  • Page 12: Restoring Factory Defaults

    Restoring factory defaults all configuration parameters can all be restored to their factory default settings by using your primary controller to reset the device. (delete from the network) software fuse this lamp module is designed to protect itself against loads that exceed its maximum power ratin...

  • Page 13: Interoperability With Z-Wave

    Interoperability with z-wave ™ devices a z-wave ™ network can integrate devices of various classes, and these devices can be made by different manufacturers. Although every z-wave certified product is designed to work with all other z-wave certified products, your controller must include the appropr...

  • Page 14: Fcc

    Fcc u2z45602-3 the federal communication commission radio frequency interference statement includes the following paragraph: the equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reas...

  • Page 15: Specifications

    Important note: to comply with the fcc rf exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the rf exposure requirements and void user’s authority to operate the device. Compliance with ...

  • Page 16

    Distributed by jasco products company llc, 10 e. Memorial road, oklahoma city, oklahoma 73114. Made in china hecho en china all brand names shown are trademarks of their respective owners. Todas las marcas que aparecen aquí son marcas registradas de sus respectivos dueños. © 2013 jasco products 4570...