- DL manuals
- Jasic
- Welding System
- MAG SERIES
- Operator's Manual
Jasic MAG SERIES Operator's Manual
Summary of MAG SERIES
Page 1
Wilkinsonstar.Com mig series mig/mag/mma compact welding machines order code ! Jm-200cs operator manual.
Page 2: Your New Product
Your new product thank you for selecting this jasic technology, wilkinson star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety pre...
Page 3: Safety Precautions
Safety precautions 1 these general safety norms cover both arc welding machines and plasma cutting machines unless otherwise noted. The equipment must only be used for the purpose it was designed for. Using it in any other way could result in damage or injury and in breach of the safety rules. Only ...
Page 4
Do not weld on coated metals, unless the coating is removed from the weld area, the area is well ventilated, and while wearing an air-supplied respirator. The coatings on many metals can give o ff toxic fumes if welded. Prevention against burns and radiation arc rays from the welding process produce ...
Page 5
Rf declaration equipment that complies with directive 2004/108/ec concerning electromagnetic compatibility (emc) and the technical requirements of en60974-10 is designed for use in industrial buildings and not those for domestic use where electricity is provided via the low voltage public distributi...
Page 6: Product Overview
Product overview 2 the unique electronic structure and air channel design in this series of machines provides e ffi cient cooling of the power devices as well as improving the duty cycles of the machines. The design of the forced air-cooling system channel can e ff ectively prevent the power devices an...
Page 7: Technical Data
Technical data 3 ① tested at the environment temperature of 40 0 c 6 parameter unit mig 200cs rated input voltage v 230v ac +/- 15% rated input power kva 9.4 mma recommended fuse a 30 welding current range a mma 10 - 200 mig 30 - 200 welding current range v mma 20.4 -28 mig 15.5 - 24 rated duty cycl...
Page 8: Controls
Controls 4 front view 1. Current/wire feed speed control knob 2. Current display window 3. 2t indicator 4. 4t indicator 5. 2t/4t switch key 6. Welding mode selecting switch 7. Gas/no gas switch 8. Socket for spool gun torch (optional) 9. "+" output terminal 10. Euro connector for torch 11. "-" outpu...
Page 9
Optional spool gun socket socket 1: push-pull torch power source ”+” socket 2: push-pull torch power source ”-” socket 3~9: null rear view 1 input power cord 2. Gas inlet 3 power switch side view 1. Handle 2. Wire-inch button 3. Gas-check button 4 wire feed system 8 ! 1 2 3 4 1 2 3.
Page 10: Installation
Installation 5 unpacking check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location the machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or c...
Page 11
Selector into the “+” output terminal of the welding machine, and tighten it clockwise. Ensuring that the groove size in the feeding position on the drive roll matches the contact tip size of the welding torch and the wire size being used. Release the pressure arm of the wire feeder to thread the wi...
Page 12: Operation
Operation before starting any welding activity ensure that you have suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the area. Mma after connecting the welding leads as detailed you will need to switch the power switch on the back panel to ...
Page 13
Multifunctional display window during welding, the current display window displays the practical welding current value, and the voltage display window displays the practical welding voltage value. In standby mode, the windows display as follows. *-it displays vrd voltage when not turning the voltage...
Page 14
Maintenance and troubleshooting 6 the following operation requires su ffi cient professional knowledge on electric aspects and comprehensive safety knowledge. Make sure the input cable of the machine is disconnected from the electricity supply and wait for 5 minutes before removing the machine covers....
Page 15: Electrical Schematic
Electrical schematic 7 14 !.
Page 16: Parts List
Parts list 8 15 1 2 14 15 16 18 19 20 21 6 5 13 22 4 7 8 12 11 10 9 17 23 24 3 27 25 26.
Page 17
16 no. Part no description no. Part no description 1 10045881 inverter 15 10041421 wire feed system 2 10041446 fan 16 10045805 display panel mounting 3 10037485 rectifier board 17 10043904 knob 4 10041723 gas connector 18 10037151 quick socket 5 10041721 silicon bridge heat sink 19 10041427 handle l...
Page 18: Order Code
Jm mig series mig/mag/mma welding machine order code ! Jm-200cs (mig 200cs) © wilkinson star limited issue 1 may 2014 product is subject to change without notice xvii.