1. DL manuals
  2. JBL
  3. Speakers
  4. 585000
  5. Installation manual

JBL 585000 Installation manual

Manual is about: JBL Professional Intellivox - DC/DS/DSH/DSX 115, 180, 280, 380, 430 & 500 models loudspeakers

Summary of 585000

  • Page 1

    Installation manual jbl professional intellivox - dc/ds/dsh/dsx 115, 180, 280, 380, 430 & 500 models (part nos. 585000, 585001, 585020, 585021, 585060, 585061, 585120, 585121, 585160, 585161, 585300, 585301, 587000, 587001, 587020, 587021, 587040, 587041, 587060, 587061, 587080, 587081, 587120, 5871...

  • Page 2

    2 201401/ivxim_v2.2 jbl intellivox installation manual this document confirms that products manufactured by duran audio bearing the ce label meet all the requirements in the emc directive 2004/108/ec and lv directive 2006/95/ec laid down by the member states council for adjustment of legal requiremen...

  • Page 3: Table Of Contents

    3 201401/ivxim_v2.2 jbl intellivox installation manual reference to statements of conformity . . . . . . . . . . . . . . . . . . . 2 user’s notice and disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    4 201401/ivxim_v2.2 jbl intellivox installation manual this symbol is intended to alert you to the presence of uninsulated dangerous voltages within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. This symbol is used throughout this manual and is in...

  • Page 5: 2. Introduction

    5 201401/ivxim_v2.2 jbl intellivox installation manual 201401/ivxim_v2.2 this manual describes the recommended installation procedure for the jbl intellivox dc (ddc2.0) and ds (dds) range of loudspeakers. The jbl intellivox is a type of loudspeaker known as an active dsp-controlled loudspeaker array...

  • Page 6

    6 201401/ivxim_v2.2 jbl intellivox installation manual a standard option applicable to all models is the position within the housing of the electronics module, which may either be at the top or bottom of the housing. The position is relevant to the installation procedure as the “acoustic centre” (se...

  • Page 7: 3. Installation Guide

    7 201401/ivxim_v2.2 jbl intellivox installation manual 201401/ivxim_v2.2 preparing for installation before starting to install the intellivox loudspeaker, a number of points should be considered. • it is assumed that the installation site has been the subject of an extensive dda investigation or opt...

  • Page 8

    8 201401/ivxim_v2.2 jbl intellivox installation manual necessary to upload the correct settings for each unit to obtain the desired acoustic coverage. Once this has been done, there is no longer an operational need to have the intellivox connected to a pc because all settings are stored locally with...

  • Page 9

    9 201401/ivxim_v2.2 jbl intellivox installation manual additional access to the connectors is available via the connector plate located between the amplifier and loudspeaker baffle. Removal of the front grille will be necessary to gain access. Ac mains the intellivox is equipped with a 3-pin iec mains...

  • Page 10

    10 201401/ivxim_v2.2 jbl intellivox installation manual wago connectors all other intellivox connections are made via the four on- board wago type 231 multi-pin connectors. These are: • audio (6-way male) • network (5-way male) • ambient noise mic/ext. Temp. Sensor (5-way female) • failure detection...

  • Page 11

    11 201401/ivxim_v2.2 jbl intellivox installation manual audio inputs the intellivox is normally supplied with two transformer- balanced line inputs. Selection of input 1 or input 2 as audio source is made from the wincontrol software via the network, and for most installations only input 1 need be w...

  • Page 12

    12 201401/ivxim_v2.2 jbl intellivox installation manual network connection the rs-485 network connection should be permanently wired in any of the following situations: • the intellivox is to be constantly monitored in operation. • the physical location of the intellivox makes access to the network ...

  • Page 13

    13 201401/ivxim_v2.2 jbl intellivox installation manual fault monitoring/fan control connector the pinout of this connector is as follows: although accessed via the same connector, the fan control and failure relay functions are independent of each other and either or both may be used, as required. ...

  • Page 14

    14 201401/ivxim_v2.2 jbl intellivox installation manual fan control an external cooling fan should be installed if the ambient temperature is expected to exceed 40 °c and/or the intellivox will be exposed to direct sunlight. For outdoor applications jbl offers an off-the-shelf solution (see weather-...

  • Page 15

    15 201401/ivxim_v2.2 jbl intellivox installation manual external ambient spl/temperature sensor the pinout of this connector is as follows: although accessed via the same connector, the external ans microphone and temperature sensor functions are independent of each other and either or both may be u...

  • Page 16

    16 201401/ivxim_v2.2 jbl intellivox installation manual mechanical installation acoustic centre mounting an intellivox loudspeaker is a straightforward procedure, but it is essential to understand that the height of the unit above floor level is extremely critical. The “correct operational height” is...

  • Page 17

    17 201401/ivxim_v2.2 jbl intellivox installation manual mounting options the intellivox has two or three (depending on the model) attachment points at the rear of the enclosure; the device should be mounted using the appropriate brackets fixed at these points. Each point consists of four m5 threaded ...

  • Page 18

    18 201401/ivxim_v2.2 jbl intellivox installation manual mounting procedure the general mounting procedure using the standard brackets is described below. It is assumed that all necessary cabling is already prepared with connectors fitted as described in the previous chapters. Proceed as follows: 1. U...

  • Page 19: 4. Unit Checks

    19 201401/ivxim_v2.2 jbl intellivox installation manual after installation and connection are complete, the installer should upload the settings file into the intellivox and verify correct operation with wincontrol software. This section of the manual describes only the file upload and a simple verific...

  • Page 20

    20 201401/ivxim_v2.2 jbl intellivox installation manual settings file upload • apply mains power to the intellivox, turn on the pc and launch wincontrol. Open options > communications options, and confirm that the off-line box is unchecked and that the correct com port is selected. Close the communic...

  • Page 21

    21 201401/ivxim_v2.2 jbl intellivox installation manual • the file name field (at the top of the load control parameters settings dialogue box) indicates the last-used settings file name. If this is the first time that the installation of wincontrol has been used, a default settings file is selected...

  • Page 22: 5. Appendix

    22 201401/ivxim_v2.2 jbl intellivox installation manual optional accessories listed below are a number of additional components which may be required for an individual installation. Mating connectors and components for external wiring: other installation-related accessories: 5. Appendix connector de...

  • Page 23

    23 201401/ivxim_v2.2 jbl intellivox installation manual available input modules: weather proofing kits: network accessories: description order code weather-proofing kit for models dc115/180, ds115/180, dsx/180 (amp at top only) 20010 weather-proofing kit for models dc280, dc380, ds280, ds380, dsx280, ...

  • Page 24

    24 201401/ivxim_v2.2 jbl intellivox installation manual common analogue grounding issues correctly connecting the intellivox to ground has several benefits: 1. Safety. The gnd terminal of the iec mains connector provides a direct low impedance path from the metal parts of the chassis to ground. Alway...

  • Page 25

    25 201401/ivxim_v2.2 jbl intellivox installation manual failure monitoring on 70 v/100 v connection. If the intellivox is equipped with an input module that supports direct interfacing to a 70 v/100 v signal, a simple failure monitoring scheme requiring no additional connections can be easily implem...

  • Page 26

    26 201401/ivxim_v2.2 jbl intellivox installation manual configuring pcb124 the impedance between pin 1 and 2 of the audio input connector has two states: • high impedance (approximately 140 kohm @ dc). • low impedance (approximately 2.2 kohm @ dc). The states are switched by a separate change-over c...

  • Page 27

    27 201401/ivxim_v2.2 jbl intellivox installation manual failure relay configuration intellivox units equipped with input board pcb124 (see fig.17) support configuration of the internal failure relay for either volt-free or impedance-sensing (10k / 20k Ω) operation. Reconfiguring the internal failure re...

  • Page 28

    Jbl professional 8500 balboa boulevard northridge, ca 91329 u.S.A. © copyright 2014 jbl professional www.Jblpro.Com.