1. DL manuals
  2. JBL
  3. Subwoofer
  4. PERFORMANCE P10SW
  5. Service Manual

JBL PERFORMANCE P10SW Service Manual

Other manuals for PERFORMANCE P10SW: Brochure, Owner's Manual
Manual is about: E-Series, Performance Series

Summary of PERFORMANCE P10SW

  • Page 1

    Models: northridge ™ e-series e150p performance series p10sw powered subwoofers service manual jbl consumer products 250 crossways park dr. Woodbury, new york 11797 rev4 4/2006.

  • Page 2: -  Contents  -

    - contents - basic specifications …………….……..…………..1 safety information …………….……..….………..2 e150p packing……..………………….….….….……...3 p10sw packing……..……………………….…………4 detailed specifications ……….……..…………..5 connections………………………...……..…...…..…6 operation ……..………………….……...…….….…...9 basic troubleshooting..…...

  • Page 3: Safety Information

    Warning any person performing service of this unit will be exposed to hazardous voltages and the risk of electric shock. It is assumed that any person who removes the amplifier from this cabinet has been properly trained in protecting against avoidable injury and shock. Therefore, any service proced...

  • Page 4: E150P

    1 5 3 14 2 4 e150p packaging ref# part number description qty 1 350883-001 manual, owner-e150p/e250p 1 2 350884-002 carton,master-e150p (beech model) 1 350884-001 carton,master-e150p (black model) 1 350884-003 carton,master-e150p (cherry model) 1 3 350885-001 pad,end,top-e150p 1 4 350885-002 pad,end...

  • Page 5: Packaging

    1 5 3 2 4 packaging p10sw 6 ref# part number description qty 1 361803-001 p10sw owner’s manual 1 2 361804-001 p10sw outer carton 1 3 350885-001 packing foam (top) 1 4 350885-002 packing foam (bottom) 1 5 338381-001 warranty card 1 6 351219-004 front grille 1 4.

  • Page 6

    Jbl e150p/p10sw powered sub/ plate amp line voltage yes/no hi/lo line nom. Unit notes us 120vac/60hz yes 108-132 120 vrms normal operation eu 230vac/50-60hz yes 207-264 230 vrms normal operation, moms required parameter specification unit qa test limits conditions notes amp section type (class ab, d...

  • Page 7

    Parameter specification unit qa test limits conditions notes turn-off transient 50 mv-peak 2v-pp @ speaker outputs ac line cycled from on to off efficiency efficiency 65 % 64 nominal line voltage 120 vac / 230 vac stand-by input power 15 watts 18 @ nom. Line voltage auto turn of time (t) must be 5 >...

  • Page 8: –

    4 analog receiver/processor – speaker-level connections use this installation method only with an analog receiver/ processor that does not have digital processing or bass management, and also does not have a subwoofer output or a volume-controlled preamp (line-) level output: connect the speaker wir...

  • Page 9

    Digital receiver/processor – lfe connection use this installation method for dolby digital, dts ® or other digital surround processors that have bass-management programming, or for analog receivers/processors that have a filtered subwoofer output: important: make sure that the lfe toggle switch on t...

  • Page 10: Operation

    Operation when the unit is plugged in and the power switch is on and no signal is received, the led on the amplifier panel will turn red. When a signal is present, the led will turn green. Note: it will take several min- utes for the led to turn from green to red after the input signal to the subwoo...

  • Page 11: Troubleshooting

    Troubleshooting if you used the high-level (speaker) inputs and there is no sound from any of the speakers: • check that the receiver/ amplifier is on and a source is playing. • check that the powered subwoofer is plugged into an active electrical outlet and is switched on. • check all wires and con...

  • Page 12: E150P

    Ref# part number description qty 1 350883-001 manual, owner-e150p/e250p 1 2 350884-002 carton,master-e150p (beech model) 1 350884-001 carton,master-e150p (black model) 1 350884-003 carton,master-e150p (cherry model) 1 3 350885-001 pad,end,top-e150p 1 4 350885-002 pad,end,bot-e150p 1 5 338381-001 war...

  • Page 13: P10Sw Exploded View

    Amplifier – not for sale ref# part number description qty 1 336486-001 asy,foot,plstc 4 2 883-31110-40 screw, 8 x 2 1/2,tr,ph,pb,blk zinc,lcs (foot) 4 3 903802-016 screw, pb,hxs,#8x1",zinc (woofer) 8 4 338127-002 asy, woofer,10" dcr 5.8 Ω 1 5 336804-001 asy, port tube 1 6 351219-004 asy, grille, blk...

  • Page 14: Test Set-Up and Procedure

    Test set-up and procedure system aural sweep test equipment needed: • function/signal generator/sweep generator • integrated amplifier • multimeter • speaker cables 1) connect a pair of level input cables (rca) from signal generator to either right or left level input on uut. Level control should be...

  • Page 15

    E150p/p10sw subwoofers 14 & p10sw & p12sw.

  • Page 16: Service Bulletin

    Service bulletin service bulletin # jbl2005-01 december 2005 warranty labor rate: minor repair to: all jbl service centers model: e150p, e250p subwoofers subject: “chirp” noise on power-up in the event you receive an e150p or e250p with the complaint: “the subwoofer make a slight “chirp” noise when ...

  • Page 17

    Jbl incorporated inc. 250 crossways park dr. Woodbury, new york 11797 tech tips troubleshooting tips and solutions to common service problems for models: e150p,e250p tip# jbltt2003-04 rev2 p10sw, p12sw pb10,pb12 (revision 2) * subject: replacing mosfets q18, q22 in the event you need to replace mosf...

  • Page 18

    A. Power amp section resistance check resistance from s+ (spk o/p) to gnd should be >1m Ω (no load) resistance from v+ (c6 p+) to v- (c8 p-) gradually fully charged should read >10k Ω resistance from v+ (c6 p+) to s+ (spk o/p) should read >1m Ω resistance from v- (c8 p-) to s+ (spk o/p) should read ...

  • Page 19

    - voltage measurements op amp u2(1) u2(14) u2(8) u3(7) u3(1) u3(14) u3(8) u5(7) u5(1) speaker o/p 133.6mv 200.2mv 245.9mv 314.8mv 314.9mv 350mv 1.67v 1.452v 2.098v 15.3v 2. High level input sensitivity -set up turn level, x’over freq pot fully cw and lfe switch off set generator at 1.15v@50hz signal...

  • Page 20

    Caution : speaker output is floating and is not protected against a short to ground. All test instruments connected to the output must be floating. Attach the scope probe tip to s - and reference lead to s+. (a 10mv signal may need from the input to trigger the switch turn on) no no yes yes no no ye...

  • Page 21

    20 e150p/p10sw subwoofers.

  • Page 22

    21 e150p/p10sw subwoofers.

  • Page 23

    22 e150p/p10sw subwoofers.

  • Page 24

    23 e150p/p10sw subwoofers.

  • Page 25

    E150p/p10sw 120v electrical parts list part number description reference designator qty resistors 020-000498-120 carbon film 0r 1/4w j r10,11 2 021-100401-120 mof resistor 1k 1w j r103 1 021-820303-020 mof resistor 820r 3ws j 8x20 r6,9 2 022-500003-020 knp resistor 0r05 3ws j fk type r104 1 024-1002...

  • Page 26

    Part number description reference designator qty 024-470798-120 smd resistor 4m7 1/8w j 0805 r60 1 024-560498-120 smd resistor 5k6 1/8w j 0805 r40,41 2 024-604598-100 smd resistor 60k4 1/8w f 0805 r39 1 024-620398-120 smd resistor 620r 1/8w j 0805 r16,18,57 3 024-680498-120 smd resistor 6k8 1/8w j 0...

  • Page 27

    Part number description reference designator qty 051-005600-100 pnp transistor pn:mpsw56rlra to-92 q3 1 051-222200-100 npn transistor pn:mps2222arlra to-92 q21 1 051-290700-100 pnp transistor pn:mps2907a rlra to-92 q19,23 2 051-540101-000 pnp transistor pn:2n5401 to-92 q1 1 051-555100-000 npn transi...

  • Page 28

    Part number description reference designator qty 072-040064-000 terminal pc250(t=0.8),t250ma 072-040096-000 terminal (t=0.8mm) pc187(0.8) 072-040169-000 connector 2 pin js-1001-2 p:2.5mm 072-060170-000 b.P. W / accessory parts 073-032316-601 black anodized 70x42x20mm 073-050001-000 fuse clip p/n:cff...

  • Page 29

    Opamp, quad tl074cdr u2, 3 opamp, dual tl072cdr so-8, njm4558m-te3 u5, 6, 4 ir2111 half-bridge driver u7 2 base 3 collector 1 emitter 1 2 3 2n5401 q1 2 base 3 collector 1 emitter 1 2 3 mpsw06rlra, mpsw56rlrampq, mps2222arlra, 2n2907a, 2n5551, q2, 16, 3, 21, 19, 23, 17 mosfet irf640 q18, 22 tip31c q4...

  • Page 30

    音 律 電 子 股 份 有 限 公 司 音 律 電 子 股 份 有 限 公 司 note: this voltage is referenced to -v, not circuit ground note: this voltage is referenced to -v, not circuit ground 29 e150p/p10sw subwoofers.

  • Page 31

    音 律 電 子 股 份 有 限 公 司 音 律 電 子 股 份 有 限 公 司 note: this voltage is referenced to -v, not circuit ground 30 e150p/p10sw subwoofers.