1. DL manuals
  2. Jeep
  3. Automobile
  4. 2009 Wrangler
  5. Owenrs Manual

Jeep 2009 Wrangler Owenrs Manual

Manual is about: Wrangler 2009

Summary of 2009 Wrangler

  • Page 1

    121413 09 wrangler om.Indd 1 121413 09 wrangler om.Indd 1 3/11/08 9:26:06 am 3/11/08 9:26:06 am.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefor. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be s...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 6

    Introduction congratulations on selecting your new chrysler llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle designed for both on-road and off-road us...

  • Page 7

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a warranty information booklet and various customer-oriented documents. Please take the time to read these publ...

  • Page 8

    Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat b...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 13 䡵 steering wheel lock . . . . . . . . . . . . . . . . . . . . 1...

  • Page 12

    ▫ to lock the doors and swing gate . . . . . . . . 21 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 21 ▫ to turn off “flash lights with lock” . . . . . . . 21 ▫ programming additional transmitters . . . . . . 22 ▫ general information . . . . . . . . . . . . . . . . . . . 22 ▫ transmitter...

  • Page 13

    䡵 occupant restraints . . . . . . . . . . . . . . . . . . . . . 38 ▫ lap/shoulder belts . . . . . . . . . . . . . . . . . . . . 39 ▫ rear center lap/shoulder belt retractor lockout (four-door models only) . . . . . . . . . 44 ▫ adjustable upper shoulder belt anchorage . . . . . . . . . . . . . . . ....

  • Page 14

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 15

    Manual transmission — if equipped 1. Turn the ignition switch to the acc (accessory) position. 2. Push the ignition key inward. 3. Turn the ignition key to the lock position, and remove the key. Warning! Leaving unattended children in a vehicle is danger- ous for a number of reasons. A child or othe...

  • Page 16

    To manually lock the steering wheel with the engine running, rotate the steering wheel one– half revolution from the straight ahead position, turn off the engine, and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To release the steering wheel lock inse...

  • Page 17

    Someone used an invalid key to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds. If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 sec- onds), it indicates that there is a fault in ...

  • Page 18

    Procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed. Note: when having the sentry key 威 immobilizer system serviced, bring all vehicle keys with you to an authorized dealer. Customer key programming if you have t...

  • Page 19

    Repeat this procedure to program up to eight keys. If you do not have a programmed sentry key 威, contact your authorized dealer for details. Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from s...

  • Page 20

    Rearming the system if something triggers the alarm, and no action is taken to disarm it, the vehicle security alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the vehicle security alarm will rearm itself. To set the alarm the vehicle se...

  • Page 21

    Illuminated entry the interior lights will come on when you open any door. The lights will remain on after all of the doors are closed, and then fade to off or they will immediately fade to off once the ignition switch is turned on. Remote keyless entry (rke) — if equipped this system allows you to ...

  • Page 22

    To unlock the doors and swing gate press and release the rke transmitter unlock button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the rke transmitter unlock button is pressed, the illuminated entry will initiate and the parking lights will flash twic...

  • Page 23

    To lock the doors and swing gate press and release the lock button on the rke transmit- ter to lock all doors. The turn signals will flash and the horn will chirp once to acknowledge the lock signal. If desired, the “sound horn on lock” feature can be turned on or off using the following steps: 1. P...

  • Page 24

    2. While the unlock button is pressed, (after four seconds) press the rke transmitter lock button. Re- lease both buttons. 3. Test the “flash lights with lock” feature outside of the vehicle, by pressing the rke transmitter lock button with the ignition in the lock position, and the key removed. Not...

  • Page 25

    If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. Weak battery in the rke transmitter. The expected life of battery is five years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile ...

  • Page 26

    Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system...

  • Page 27

    To enter remote start press and release the remote start button on the rke transmitter twice, within five sec- onds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the remote start mode for a 15-minute cycle. No...

  • Page 28

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15-minute cycle, insert the key into the ignition s...

  • Page 29

    Upper half door window installation — if equipped 1. Grasp the half door window and line up pins into pockets in lower door. 2. Push down to ensure the half door window is fully seated. Front door removal warning! Do not drive your vehicle on public roads with the doors removed as you will lose the ...

  • Page 30

    Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected. 3. Unhook the door strap from ...

  • Page 31

    Rear door removal (four-door models) warning! Do not drive your vehicle on public roads with the doors removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. 1. Remove the hinge pin screws from the upper and lower outside hi...

  • Page 32

    Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected. 5. Unhook the door strap from ...

  • Page 33

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, and console storage. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • never leave chil...

  • Page 34

    Power door locks — if equipped the door lock switch is located on each front door panel. Press the switch downward to lock the doors, and upward to unlock the doors. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park an...

  • Page 35

    Automatic unlock doors on exit the doors will unlock automatically on vehicles with power door locks if: 1. The “automatic unlock doors on exit” feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission shift lever is in neutral or park...

  • Page 36

    Automatic door locks the doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The “automatic door locks” feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4. The throttle is pressed. 5. The vehicle speed is above 15...

  • Page 37

    Windows power windows — if equipped the power window switches are located on the instru- ment panel center stack (below the radio). The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger wind...

  • Page 38

    Auto-down both the driver and front passenger window switches have an “auto-down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down move- ment, operate the switch in either the up or down direction and release the swit...

  • Page 39

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down in certain open or partially open posi- tions. This is a normal occurrence and can be minimized by adjusting ...

  • Page 40

    Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flip-up window clos...

  • Page 41

    Warning! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up prope...

  • Page 42

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat using a seat belt properly. • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bo...

  • Page 43

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” pulling out the lap/shoulder belt latch plate inserting latch plate into buckle 2 things to know before starting your vehicle 41.

  • Page 44

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is loose will not protect you as well. In a sudden stop you ...

  • Page 45

    Note: the seat belt reminder light will remain on until the driver’s seat belt is buckled. Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as lo...

  • Page 46

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protecti...

  • Page 47

    Warning! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seatback is in the fully upright and locked position when occupied. If the rear seatback is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, th...

  • Page 48

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 49

    Once the warning is triggered, the beltalert 威 will con- tinue to chime and flash the seat belt reminder light for 96 seconds or until the driver’s seat belt is buckled. The beltalert 威 will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is great...

  • Page 50

    Seat belts and pregnant women we recommend that pregnant women use seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so...

  • Page 51

    Note: these airbags are certified to the new federal regulations for advanced airbags. The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on the severity and type of collision. 1 — driver airbag 2 — passenger airba...

  • Page 52

    If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled srs. Note: airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. Warning! • do not put anything on or around the...

  • Page 53

    Warning! (continued) • if your vehicle is equipped with side airbags, do not attach cupholders or any other objects on or around the door. The inflating side airbag could drive the objects into occupants, causing serious injury. • do not cover or place items on the airbag covers. These items may cau...

  • Page 54

    If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (refer to information on child restraints in this section.) you should read the instructions provided with your child r...

  • Page 55

    Airbag system components the airbag system consists of the following: • occupant restraint controller (orc) • airbag warning light • driver front airbag • front passenger airbag • front seat-mounted side airbags (if equipped) • steering wheel and column • instrument panel • knee impact bolsters • fr...

  • Page 56

    The advanced front airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front airbags...

  • Page 57

    Warning! Ignoring the airbag warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked immediately. • the driver and...

  • Page 58

    The orc monitors the readiness of the electronic parts of the system whenever the ignition switch is in the start or on positions. These include all of the items previously mentioned. Based on the severity and type of collision, the side airbag inflator on the crash side of the vehicle is triggered,...

  • Page 59

    • as the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area w...

  • Page 60

    • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injur...

  • Page 61

    Event data recorder (edr) in the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data param- eters (see the following list) in an event data recorder prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed...

  • Page 62

    Upon request. General data that does not identify par- ticular vehicles or crashes may be released for incorpo- ration in aggregate crash databases, such as those main- tained by the u.S. Government and various states. Data of a potentially sensitive nature, such as would identify a particular drive...

  • Page 63

    • traction/stability control status • tire pressure monitoring system status child restraint everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states and all canadian provinces require that small children ride in proper restraint s...

  • Page 64

    • the infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children w...

  • Page 65

    Here are some tips for getting the most out of your child restraint: • before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use i...

  • Page 66

    • buckle the child into the restraint exactly as the manufacturer’s instructions tell you. • when your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the oc...

  • Page 67

    • check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • if the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind the back. Note: for additional ...

  • Page 68

    Note: if your child restraint seat is not latch- compatible, install the restraint using the vehicle seat belts. Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a...

  • Page 69

    Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked be...

  • Page 70

    Installing the latch-compatible child restraint system we urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provide...

  • Page 71

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch anchorages (four-door models) tether strap mounting (two-door models) 2 things to know before starting your vehicle 69.

  • Page 72

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means for adjusting the tension of the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also b...

  • Page 73

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 74

    To attach a child restraint tether strap: route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head rest, and attach the hook to the tether anchor located on the back of the s...

  • Page 75

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting pets airbags deploying in the front seat could harm your pet. An...

  • Page 76

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not inter- preted as an indication of difficulty. Safety tips transporting passengers never transport passengers in the cargo area. Warning! • ...

  • Page 77

    Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at hig...

  • Page 78

    Airbag warning light the light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked b...

  • Page 79: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 81 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 82 䡵 uconnect威 phone . . . . . . . . . . . . . . . ....

  • Page 80

    ▫ to raise the rear seat . . . . . . . . . . . . . . . . . 92 䡵 to open and close the hood . . . . . . . . . . . . . 93 䡵 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 ▫ multifunction lever . . . . . . . . . . . . . . . . . . . 94 ▫ parking lights, instrument panel lights and...

  • Page 81

    ▫ manual transmission . . . . . . . . . . . . . . . . . 105 ▫ to accelerate for passing . . . . . . . . . . . . . . 105 䡵 electrical power outlet . . . . . . . . . . . . . . . . . 106 䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 108 ▫ front cupholders . . . . . . . . . . . . . . ...

  • Page 82

    ▫ door frame removal — four-door models . . . . . . . . . . . . . . . . . . . . 126 ▫ door frame installation — four-door models . . . . . . . . . . . . . . . . . . . . 129 䡵 soft top — two door models . . . . . . . . . . . . 131 ▫ folding down the soft top . . . . . . . . . . . . . 134 ▫ putting up...

  • Page 83

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward...

  • Page 84

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than the...

  • Page 85

    Voice recognition button (uconnect 威 phone) when you press this button, a “not equipped with uconnect 威” message will display on your radio screen. Phone button (uconnect 威 phone) when you press this button, a “not equipped with uconnect 威” message will display on your radio screen. Seats front seat...

  • Page 86

    Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Only adjust a seat while the vehicle is parked. Manual seat height adjustment — if equipped the ...

  • Page 87

    Front seatback recline lean forward before lifting the handle, then lean back to the desired position and release the handle. Lift the handle to return the seatback to an upright position. Front easy entry seats — two door models push the lever on the seatback rearward (toward the rear of the vehicl...

  • Page 88

    Easy entry combination lever — if equipped easy entry seat 86 understanding the features of your vehicle.

  • Page 89

    1. To return the seat to a sitting position, rotate the seatback upright until it locks. 2. Push the seat rearward until the track locks. Note: • the front driver seat has a full recliner memory, which will allow the seatback to be returned to its original position. If equipped with combination leve...

  • Page 90

    The restraints may be raised without pushing in the button. The rear head restraints are not adjustable. Fold and tumble rear seat — two door models note: • prior to folding the rear seat, it may be necessary to reposition the front seats. • be sure that the front seats are fully upright and positio...

  • Page 91

    3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position. Removing the rear seat — two door models warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in...

  • Page 92

    1. Remove the three rear subwoofer (if equipped) mounting nuts using a 15 mm socket. 2. Unplug the electrical connector from the rear sub- woofer (if equipped). 3. Fold the rear seat forward following steps 1 through 3 under “fold and tumble rear seat” in this section. 4. Press down on the release b...

  • Page 93

    Replacing the rear seat — two door models reverse the steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the ve- hicle. • the rear cargo space is intended for load carr...

  • Page 94

    To fold down the rear seat locate the pull strap (lower outboard side of seat), and pull it toward you until the seatback releases. To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty...

  • Page 95

    To open and close the hood release both the hood latches. Raise the hood and locate the safety latch, located in the middle of the hood opening. Push the latch to the left side of the vehicle, to open the hood. You may have to push down slightly on the hood before pushing the safety latch. Insert th...

  • Page 96

    Lights multifunction lever the multifunction lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming and turn signals. The lever is located on the left side of the steering column. Multifunction lever 94 unde...

  • Page 97

    Parking lights, instrument panel lights and headlights turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the center portion of ...

  • Page 98

    Headlight dimmer switch push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam. Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer...

  • Page 99

    Daytime running lights — if equipped the headlights come on at a low intensity level after the vehicle has been driven approximately 3 ft (1 m). They will turn off when the vehicle is turned off or when the headlights are switched on. Interior lights the overhead light will come on when a door is op...

  • Page 100

    When a door is open and the interior lights are on, rotating the dimmer control all the way down to the off detent will cause all the interior lights to turn off. This is also known as the ⬙party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehi...

  • Page 101

    Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. High/low speed 1 — ...

  • Page 102

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Move the lever to the delay position, then select the delay interval by turning the end of the lever. The delay can be regulated between 2 to 30...

  • Page 103

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is p...

  • Page 104

    Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Pull upwards on the lever to lock the column firmly in place. Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a st...

  • Page 105

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated simultaneously. If this occurs, the electronic speed con- trol system can be reactivated by pushing the electronic speed control on/off but...

  • Page 106

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the electronic speed control system off when you are not using it. To set a de...

  • Page 107

    Tapping resume accel once will result in a 1 mph (1.6 km/h) speed increase. Each time the electronic speed control lever is tapped, speed increases so that tapping the electronic speed control lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while the electronic spee...

  • Page 108

    Using electronic speed control on hills note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain and/or more frequent downshifts (auto transmission only) may occur so it may be prefera...

  • Page 109

    The right-side power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting. Warning! To avoid serious injury or death: • only connectors designed for use in this type of outle...

  • Page 110

    Caution! (continued) • power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Cupholders front cupholders the front cupholders are located in the center console. Note: the front cupholder insert is removable for cleaning. Front cu...

  • Page 111

    Rear cupholders the rear cupholders are located on the back of the center console. Storage console storage compartment to lock or unlock the storage compartment, insert igni- tion the key and turn. To open the storage compartment, press the latch and lift the cover. Rear cupholders center console 3 ...

  • Page 112

    Rear storage compartment the rear storage compartment cover is held by a spring- loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: note: the rear storage compartment latch should not be used as cargo tie-down. 1. Flip up the pull loop so it is perpen...

  • Page 113

    Hard top are to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top. Your vehicle warranty will not cover damage resulting from both tops remaining on the vehicle at the same time for extended periods of time. Removing the soft top 1. Locate and remove t...

  • Page 114

    4. Using a rubber mallet, carefully tap the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx 威 head driver. Re...

  • Page 115

    1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (four for two-door models, six for four-door models) • right and left quarter windows • rear window 2. Remove the hard top. Refer to “freedom top three- piece modular hard t...

  • Page 116

    B. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the bows facing upward. C. Tap the knuckles on the side with a rubber mallet to reattach them to the metal pivot brackets. D. Screw the pivot screws back into place using a #t30 torx 威 head driv...

  • Page 117

    Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 6. U...

  • Page 118

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew: • it is recommended that the top be free of water prior to panel removal. Removing the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicles interior. • the ...

  • Page 119

    3. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 4. Turn the rear fasteners (knobs) (located on the over- head speaker bar assembly) counter-clockwise until they can be removed. 3 understanding the features of your vehicle 117.

  • Page 120

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the panel. To remove the right panel, follow the steps above except for step 2. Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are...

  • Page 121

    Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body. 2. Install the right panel first, then the left panel. 3. Reinstall the panel(s) using the sam...

  • Page 122

    5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate the wire harness on the left rear inside corner of the vehicle. 7. Disconnect the rear window washer hose and install the tethered cap. 120 understanding the features of your vehicl...

  • Page 123

    Caution! Make sure the storage cap is installed to prevent foreign materials from entering the washer tube and clogging system, and also to prevent fluid from being sprayed into the rear of the vehicle. 8. Disconnect the wire harness from the hard top by pressing the tab at the side of the connector...

  • Page 124

    Rear hard top installation note: if the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. Install the hard top using the same steps for removal in reverse order. Note: make ...

  • Page 125

    Caution! (continued) • careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle’s interior. • the door frame(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. D...

  • Page 126

    2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle. 4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! • do not drive your vehic...

  • Page 127

    Warning! Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. Door frame installation — two-door models 1. Unfold door frame and unscrew thumbscrews. 2. Set the door fr...

  • Page 128

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame removal — four-door models 1. Unscrew and remove the two forward most door frame attachment knobs. Warning! Use both hands to remove the door frames. The door frames will fold and could cause injur...

  • Page 129

    2. Place one hand on the upper rear and one hand on the upper front of the front door frame. 3. Pull the frame toward you with your front hand to remove the frame from the vehicle. 4. Unscrew and remove the remaining door frame at- tachment knob on the rear door frame. 3 understanding the features o...

  • Page 130

    5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame toward you with your rear hand to remove the frame from the vehicle. 6. Screw the knob back into the door frame and fold for storage. Store in a secure location. Warning! • do not drive your ve...

  • Page 131

    Warning! Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. Door frame installation — four-door models 1. Install the rear door frame first. 2. Set the door frame pin...

  • Page 132

    5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. Then, clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. Position the rear of the front door frame to lay on top o...

  • Page 133

    Soft top — two door models please visit the owners section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a struct...

  • Page 134

    Caution! (continued) • refer to “appearance care for fabric top models” in section 7 of this manual. It contains important information on cleaning and caring for your vehi- cle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing t...

  • Page 135

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 136

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — sail panel 9 — front retainer — quarter window 5 — plastic retainer 10 — bottom retainer — quarter window 134 understanding the features of your vehicle.

  • Page 137

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 3 understanding the features of your vehicle 135.

  • Page 138

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 139

    4. Release the header latches and leave the hooks in the loops on the windshield. 5. Open the swing gate. 6. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate bracket...

  • Page 140

    • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage it from the zipper on the top cover. Stow the windows carefully to avoi...

  • Page 141

    10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 11. As you begin to lower the top, fold the sail panels so that they rest on top of the soft to...

  • Page 142

    12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 13. Completely release the latches from the loops on the wi...

  • Page 143

    14. Make sure the plastic sleeves are slid forward over the sunrider 威 link (sunrider威 models only). 15. Unlatch the side bows from both door rails (sun- rider 威 models only). 16. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Mov...

  • Page 144

    Note: help from another person will ease this opera- tion. 17. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. When the top is completely down, position the drip rails so they make a “v-s...

  • Page 145

    Putting up the soft top 1 — header bow 6 — body side retainer 2 — 2– bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — sail panel 9 — front retainer — quarter window 5 — plastic retainer 10 — bottom retainer — quarter window 3 understanding the features of your vehicle 143.

  • Page 146

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 144 understanding the features of your vehicle.

  • Page 147

    1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “door frame” in this section. 3. Make sure the plastic sleeve is slid rearward over sunrider 威 link (sunrider威 models only). 4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow ...

  • Page 148

    6. Make sure the sunrider 威 bracket on the side bows latches to the door rails (sunrider 威 models only). 7. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 8. If the swing gate brackets were removed, install them by hooking the rear edge...

  • Page 149

    9. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 10. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to rea...

  • Page 150

    11. To install the side windows, affix the window tem- porarily by attaching to the velcro 威 in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 12. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on...

  • Page 151

    13. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 152

    14. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 150 understanding the features of your vehicle.

  • Page 153

    15. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 3 understanding the features of your vehicle 151.

  • Page 154

    16. Run the zipper fully around to the right side of the window. 17. Grasp the swing gate bar and position it into the swing gate brackets. 18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 19....

  • Page 155

    20. Close the header latches and return the sun visors to their secured position. Soft top (four-door models) please visit the owner’s section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ...

  • Page 156

    Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place. If the tempera- ture is 41°f (5°c) or below, do not attempt to put the top down or roll the rear or side curtains. Caution! • do not run a f...

  • Page 157

    Warning! • do not drive the vehicle with the rear window curtain up unless the side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • the fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain oc...

  • Page 158

    Note: do not remove any of the three attachment knobs unless you are planning on installing the hard top. 156 understanding the features of your vehicle.

  • Page 159

    Folding down the soft top 1 — header bow 6 — body side retainer 11 — plastic retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 3 understanding the features of your vehicle 157.

  • Page 160

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 158 understanding the features of your vehicle.

  • Page 161

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 162

    4. Release the header latches and hooks from the loops on the windshield frame. 5. Open the swing gate. 6. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets....

  • Page 163

    • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage it from the zipper on the top cover. Stow the windows carefully to avoi...

  • Page 164

    10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 11. Fold the sail panels so that they rest on top of the soft top. 162 understanding the featur...

  • Page 165

    12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 13. Grasp the front side bow behind the header, and lift th...

  • Page 166

    14. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 15. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle and move the material into two folds. 164 understanding the features ...

  • Page 167

    16. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 17. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Grasp the folded ...

  • Page 168

    18. Gently slide the side bows off the door frame track and lower the top down into the vehicle. Note: help from another person will ease this opera- tion. 19. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside...

  • Page 169

    Putting up the soft top 1 — header bow 6 — body side retainer 11 — plastic retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 3 understanding the features of your vehicle 167.

  • Page 170

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 168 understanding the features of your vehicle.

  • Page 171

    Note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section. 2. Undo the straps used to secure the top in the down position and store in se...

  • Page 172

    5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 6. Ensure that the top locks into the sunrider 威 locking mechanisms that are located above the front of the rear doors. 170 understanding the features of your vehicle.

  • Page 173

    7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Before attaching the header latches, be sure the top retainers above the doors do not get trapped between the top and the door frame. Also, m...

  • Page 174

    10. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 11. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel...

  • Page 175

    12. Ensure that the straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow). Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–...

  • Page 176

    13. To install the side windows, affix the window tem- porarily by attaching it to the velcro 威 in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm). 14. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly posi...

  • Page 177

    15. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 178

    16. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 176 understanding the features of your vehicle.

  • Page 179

    17. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 18. Run the first zipper fully around to the right side of the window. 19. Grasp the swing gate bar...

  • Page 180

    21. Open the doors and insert the top retainers into the channels in the door frame above the doors, starting at the front and working toward the rear of the vehicle. 22. Ensure the plastic retainer is tucked in properly at the b-pillar and not pinching the seal. 178 understanding the features of yo...

  • Page 181

    23. Close the header latches and return the sun visors to their secured position. Sunrider 姞 (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving ...

  • Page 182

    Opening the sunrider 姞 1. Insert your finger behind the plastic retainer. Pull down and roll the retainer out of the channel. Repeat this on the other side. 2. Unclip and move the sun visors to the side. 3. Release the header latches from the loops on the windshield frame. 180 understanding the feat...

  • Page 183

    4. Slide the plastic sleeve forward. 5. Grasp the header and lift the top back. Make sure the material is folded back as shown. Note: the sunrider 威 latch on the door rail should not be activated for sunrider 威 use. If activated, the soft top must be reinstalled starting from the sail panels. 3 unde...

  • Page 184

    6. Locate the straps to secure the side bows. Wrap the straps around the bows as shown. Repeat on the other side. 7. Reposition the sun visors. Closing the sunrider 姞 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the ...

  • Page 185

    Sunrider 姞 (four-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving faster than 40 mph (64 km/h) with the sunrider 威 feature open, it is recom- mende...

  • Page 186

    2. Unclip and move the sun visors to the side. 3. Release the header latches from the loops on the windshield frame. 4. Grasp the front side bow behind the header, and lift the top. 184 understanding the features of your vehicle.

  • Page 187

    5. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 6. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle and move the material into two folds. Ensure that the straps are securely stowed. 7. Close the fr...

  • Page 188

    8. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro 威 to itself; use one strap on each side of the vehicle. To close perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to sag and may blo...

  • Page 189

    Raise the windshield and reinstall the side bars as soon as the task that required their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down...

  • Page 190

    Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assist in properly reinstalling side bars, mark the original locations prior to removing. 2. Remove the two top hex bolts (13 mm), and the one side hex bo...

  • Page 191

    Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 5. Remove the side bar assembly, and reattach the sport bar velcro 威 covering. 6. To safely store the ...

  • Page 192

    7. Remove the windshield wiper arms by first pulling the wiper away from the windshield and out to the “lock” position. Unsnap the wiper arm nut caps, and remove the retaining nuts. Lift the wiper arms off and store them in the center console or securely behind the rear seat. Note: it may be necessa...

  • Page 193

    Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach the rear of the side bar to the sport bar. Refer to step 4 of “lowering windshield and removing side bars” earlier in this section. • reattach the sport bar velcro威 covering. 3. Attach the front of the side bar...

  • Page 194

    5. Install the lower windshield plates with the six black round-headed torx 威 head screws (using a #40 torx威 head driver) on each side of the base of the windshield. 6. Reinstall the wiper arms. Rear window features — hard top only rear window wiper/washer — if equipped a rotary ring switch on the c...

  • Page 195

    If the rear wiper is operating when the ignition is turned to the lock position, the wiper will automatically return to the “park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at. Rear window defroster — if equipped the rear window d...

  • Page 196

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 197: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 198 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 199 䡵 instrument cluster description . . . . . . . . . . . . 200 䡵 compass and trip computer — if equipped . . . . . . . . . . . . ....

  • Page 198

    䡵 sales code (rer/ren) — am/fm/cd/dvd radio – if equipped . . . . . . . . . . . . . . . . . . . . 234 ▫ operating instructions — voice recognition system (vr) — if equipped . . . . . . . . . . . . . 234 ▫ operating instructions — uconnect威 phone — if equipped . . . . . . . . . . . . . . . . . . . . ...

  • Page 199

    ▫ selecting uconnect威 studios (satellite) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . 259 ▫ reception quality . . . . . . . . . . . . . . . . . . . . 259 ▫ operating instructions — uconnect威 studios (satellite) mode...

  • Page 200

    Instrument panel features 1 — air outlet 6 — climate controls 2 — instrument cluster 7 — power outlet 3 — horn 8 — lower switch bank 4 — radio 9 — auxiliary power outlet / cigar lighter 5 — glove compartment 198 understanding your instrument panel.

  • Page 201

    Instrument cluster 4 understanding your instrument panel 199.

  • Page 202

    Instrument cluster description 1. Fuel gauge the pointer shows the level of fuel in the fuel tank. Note: when the ignition switch is turned to off, the fuel gauge, voltmeter, oil pressure and temperature gauges may not show accurate readings. When the engine is not running, turn the ignition switch ...

  • Page 203

    6. Front axle lock indicator — if equipped indicates when the front axle lock has been activated. 7. Seat belt reminder light a warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on for about six second...

  • Page 204

    11. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake syste...

  • Page 205

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 206

    13. Airbag warning light this indicator lights and remains lit for six to eight seconds when the ignition is first turned on. If the light does not come on for six to eight seconds, stays on or comes on while driving, have the airbag system checked by an authorized dealer. 14. Rear axle lock indicat...

  • Page 207

    Caution! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear continuo...

  • Page 208

    21. Odometer / trip odometer reset button press this button to change the display from odometer to either of the two trip odometer settings. Trip a or trip b will appear when in the trip odometer mode. Press and hold the button for two seconds to reset the trip odometer to 0 miles or kilometers. The...

  • Page 209

    Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

  • Page 210

    U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the...

  • Page 211

    Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem contin...

  • Page 212

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. 25. Malfunction indicator light (mil) the malfunction indicator light (mil) is a part of an onboard diagnostic system called obd ii that monitors ...

  • Page 213

    26. Electronic stability program (esp) indicator light / traction control system (tcs) indicator light if the electronic stability program (esp) / traction control system (tcs) indicator light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. T...

  • Page 214

    Warning! If a warning light remains on the system may not be working and you will not have the benefit of esp or bas. Under certain driving conditions, where esp or bas would be beneficial, you - if you have not adjusted your driving speeds and stopping in or to account for the lack of the feature, ...

  • Page 215

    32. Compass / mini-trip computer button—if equipped press this button to switch between the different functions. Compass and trip computer — if equipped the compass/trip computer is located in the instru- ment cluster. It features a driver-interactive display (dis- plays information such as outside ...

  • Page 216

    Reset / change display press and hold the left button (on the instrument cluster) while function is being displayed to reset or change the display. The following trip displays can be reset or changed: • avg eco (changes to present fuel economy) • et (will reset display) trip conditions average fuel ...

  • Page 217

    Compass temperature display this display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. Warning! Even if the display still reads a few degrees above 32°f ( 0°c), the road surface may be icy, particularly in woods or on bridges. Dri...

  • Page 218

    Automatic compass calibration the self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the cal symbol will appear (blinking) on the display. After the vehicle has completed at lea...

  • Page 219

    3. Manual compass calibration has been initiated. Drive the vehicle slowly in one or more circles under 5 mph (8 km/h) in an area free from large metal objects until the cal symbol is extinguished. When the cal symbol is no longer displayed, the compass is calibrated and should display correct head-...

  • Page 220

    Note: the u.S./metric display will change from en- glish to metric or metric to english before the var symbol appears, however, it will revert back to its original setting after programming the compass func- tions. Outside temperature if the outside temperature is more than 131°f (55°c), the display...

  • Page 221

    Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume con...

  • Page 222

    Scan button pressing the scan button causes the tuner to search for the next listenable station in am, fm or satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press the scan button a second time. Voice recognit...

  • Page 223

    5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the setup button and selecting the “set home clock” entry. Once in this display follow the above procedure, starting at step 2. Info button press the info button for an rds station (one with call letters di...

  • Page 224

    Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button...

  • Page 225

    Program type 16-digit character display personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r & b sports sports talk talk top 40 top 40 weather weather by pressing the seek button...

  • Page 226

    • disc play/pause - you can toggle between playing the dvd and pausing the dvd by pushing the select button (if equipped). • dvd play options - selecting the dvd play options will display the following: • subtitle – repeatedly pressing select will switch subtitles to different subtitle languages tha...

  • Page 227

    Tune/scroll control knob to adjust the minutes. Press the tune/scroll control knob again to save changes. • player defaults - selecting this item will allow the user to scroll through the following items and set defaults according to customer preference. Menu language — if equipped selecting this it...

  • Page 228

    Aspect ratio — if equipped selecting this item allows you to choose between wide screen, pan scan, and letter box. Autoplay — if equipped when this is set to on and a dvd video is inserted, it will bypass the dvd menu screen and automatically play the movie. In some rare cases, the dvd player may no...

  • Page 229

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory {12 am, 12 fm, and 12 satellite (if equipped) stations}. Disc button pressing the disc button will allow you to switch from ...

  • Page 230

    Radio display will show ⬙loading disc⬙ when the disc is loading and “reading disc” when the radio is reading the disc. Caution! This cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. Eject button — ejecting compact disc(s) press the e...

  • Page 231

    Rw/ff (cd mode) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (rewind) button works in a similar manner. Am or fm button (cd mode) switches the radio into the am or fm radio mode. Notes on playing mp3...

  • Page 232

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3/ wma files). Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession ...

  • Page 233

    Id3 tag information for artist, song title, and album title are supported for id3 version 1 tags. Id3 version 2 is not supported by the radios. Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3/wma files when a medium containing mp3/wma data is loaded, the radio chec...

  • Page 234

    Info button (disc mode for mp3/wma play) pressing the info button repeatedly will scroll through the following tag information: song title, artist, file name, and folder name (if available). Press the info button once more to return to ⬙elapsed time ⬙ priority mode. Press and hold the info button fo...

  • Page 235

    Time button (auxiliary mode) press the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxiliary mode) no function. Operating instructions — voice recognition system (vr) (if eq...

  • Page 236

    Intended for home and other limited viewing uses only, unless otherwise authorized by macrovision. Reverse engineering or disassembly is prohibited. Dts™ ⬙dts™⬙ and ⬙dts™ 2.0⬙ are trademarks of digital the- ater systems, inc. Sales code (rer/ren) — am/fm/cd/dvd radio – if equipped note: the sales co...

  • Page 237

    To manually set the clock — rer/ren 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “user clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “hour” with the arrow pointin...

  • Page 238

    Show time if radio is off when selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the scre...

  • Page 239

    Sales code res — am/fm stereo radio with cd player (mp3 aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (r...

  • Page 240

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 241

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 242

    Set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these butt...

  • Page 243

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 244

    The current selection. Pressing and holding the seek button will allow faster scrolling through the tracks in cd and mp3 modes. Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold the ff (fast forward) butt...

  • Page 245

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 246

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 247

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 248

    Sales code res/rsc — am/fm stereo radio with cd player (mp3 aux jack) and sirius radio note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power swi...

  • Page 249

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice recognition system (radio) — if equipped refer to “voice recognition system (vr)” in s...

  • Page 250

    5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the setup button. For vehicles equipped with satellite radio, press the setup button, use the tune/scroll control to select set clock, and then follow the above procedure, starting at step 2. For vehicles n...

  • Page 251

    Scroll control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. ...

  • Page 252

    Program type 16-digit character display personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button w...

  • Page 253

    Am/fm button press the button to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1–6) you wish ...

  • Page 254

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 255

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 256

    Press the set/rnd button a second time to stop ran- dom play. Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 fil...

  • Page 257

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3 files). Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for c...

  • Page 258

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 259

    Press and hold the info button for three seconds or more and the radio will display song titles for each file. Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which all...

  • Page 260

    Uconnect 姞 studios (satellite radio) — if equipped (ren/req/rer/res/reu radios only) satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius satellite radio. This service offers over 130 c...

  • Page 261

    Sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Esn/sid access with ren/rer radios while in sat mode, press the menu button on the radio faceplate. Next, touch the subscription tab on the touch screen. All t...

  • Page 262

    • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Operating instructions — uconnect 姞 studios (satellite)...

  • Page 263

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button — except reu...

  • Page 264

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 265

    Operating instructions — video entertainment system (ves)™ (if equipped) refer to separate “video entertainment system (ves)™ guide.” cd/dvd maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is s...

  • Page 266

    Climate controls manual heater only the controls for the heating/ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain the desired interior condi- tions. Mode control the mode control allows you to choose from several pat- terns of air di...

  • Page 267

    Air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet. Mix air is directed through the floor, defrost and side window demist ou...

  • Page 268

    Manual heating and air conditioning system — if equipped the controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. The instrument panel features four airflow reg...

  • Page 269

    Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level air is directed through the panel and floor outlets. Note: there is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to t...

  • Page 270

    Blower control use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the off position. Temperature control use this control to regulate the temperature of the air inside the passenger compart...

  • Page 271

    Note: continuous use of the “recirculation” mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. In cold or damp weather, the use of the “recirculation” mode will cause windows to fog on the inside because of moisture buildup inside the vehi...

  • Page 272

    Max a/c for maximum cooling, select ei- ther the panel or bi-level position using the mode control. Then, press the “a/c” and the “recir- culation” buttons so that both lights are illuminated, and set the temperature control to its coolest setting. Note: • recirculation mode will not operate in floo...

  • Page 273

    Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer operation air conditioned veh...

  • Page 275: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 277 ▫ manual transmission . . . . . . . . . . . . . . . . . 277 ▫ automatic transmission . . . . . . . . . . . . . . . 277 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 277 ▫ extreme cold weat...

  • Page 276

    ▫ automatic transmission with overdrive . . . . 287 䡵 four–wheel drive operation (command-trac i威 or rock-trac 威) — if equipped . . . . . . . . . . . . . 291 ▫ operating instructions/precautions . . . . . . . 291 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 293 ▫ shifting procedure ...

  • Page 277

    䡵 anti-lock brake system . . . . . . . . . . . . . . . . . 316 䡵 electronic brake control system . . . . . . . . . . . 318 ▫ anti-lock brake system (abs) . . . . . . . . . . . 319 ▫ traction control system (tcs) . . . . . . . . . . . 319 ▫ brake assist system (bas) . . . . . . . . . . . . . . 320 ▫ ...

  • Page 278

    ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . 353 ▫ general information . . . . . . . . . . . . . . . . . . 356 䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . 356 ▫ reformulated gasoline . . . . . . . . . . . . . . . . 357 ▫ gasoline/oxygenate blends . . . . . . . . . ...

  • Page 279

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat buildup may cause serious injury or death. Manual transmission apply ...

  • Page 280

    Tip start feature — automatic transmission only turn the ignition switch to the start position and release it as soon as the starter engages. The starter motor will continue to run, but will automatically disengage itself when the engine is running. If the engine fails to start, the starter will dis...

  • Page 281

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. If the ve...

  • Page 282

    If the engine shows no sign of starting after two 15– second periods of cranking with the accelerator pedal held to the floor, repeat the “normal starting” or “ex- treme cold weather” procedures. With tip start — automatic transmission only if the engine fails to start after you have followed the “n...

  • Page 283

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is found under the hood bundled in front o...

  • Page 284

    Note: during cold weather, you may experience in- creased effort in shifting until the transmission fluid warms up. This is normal. Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use 1st gear when s...

  • Page 285

    Manual transmission shift speeds in mph (km/h) en- gine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.8l accel. 15 (24) 24 (39) 34 (55) 47 (76) 56 (90) cruise 10 (16) 19 (31) 27 (43) 37 (60) 41 (66) downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when drivin...

  • Page 286

    Maximum recommended downshift speeds caution! Failure to follow the maximum recommended down- shifting speeds may cause the engine to overspeed and/or damage the clutch disc, even if the clutch pedal is pressed. Manual transmission downshift speeds in mph (km/h) gear selec- tion 6 to 5 5 to 4 4 to 3...

  • Page 287

    Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine i...

  • Page 288

    Brake/transmission interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in the park position when the ignition switch is in the lock position. To move the shift lever out of the park position, the ignition switch must be turned ...

  • Page 289

    6. Press the shifter release button and shift into neu- tral. 7. The vehicle may then be started in neutral. Have your vehicle inspected by your local authorized dealer if the shift lock manual override has been used. Automatic transmission with overdrive shifting from drive to park or reverse (or f...

  • Page 290

    Gear ranges note: under extreme cold temperatures (-10°f (-23°c) and when in drive, transmission operation may be briefly limited to only second gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level. Do not race the engine when shifting from par...

  • Page 291

    Reverse this range is for moving the vehicle backward. Use only after the vehicle has come to a complete stop. Neutral this range is used when vehicle is standing for pro- longed periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. No...

  • Page 292

    If the transmission overheats, a “hotoil” message will be displayed in the odometer and a chime will sound. Overdrive can be locked out by pressing the o/d off switch located on the center console. The “o/d off indicator light” (on the switch) will illuminate to show that the switch has been activat...

  • Page 293

    Caution! • before moving the shift lever out of park, you must turn the ignition from lock so the steering wheel and shift lever are released. Otherwise, damage to the steering column or shift lever could result. • never race the engine with the brakes on and the vehicle in gear, and never hold the ...

  • Page 294

    • 4l (four-wheel drive low range) the transfer case is intended to be driven in the 2h position for normal street and highway conditions such as hard-surfaced roads. In the event that additional traction is required, the transfer case 4h and 4l positions can be used to lock the front and rear drives...

  • Page 295

    Note: do not attempt to shift when only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer, and the front and rear driveshaft speeds must be equal for a shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the tr...

  • Page 296

    4h position this range locks the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This range (4h) provides additional traction for loose, slippery road surfaces and should not be used on wet or dry pavement. The “4wd indicator light” (located in the...

  • Page 297

    4h to 4l or 4l to 4h with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission into neutral (n), or press the clutch pedal on a manual transmission. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do...

  • Page 298

    Warning! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. Axle lock (tru–lok 姞) — rubicon models the axle lock switch i...

  • Page 299

    To activate the system, press the bottom of the axle lock switch once to lock the rear axle only (the “rear axle lock indicator light” will illuminate), press the bottom of the switch again to lock the front axle (the “front axle lock indicator light” will illuminate). When the rear axle is locked, ...

  • Page 300

    The rear axle lock will disengage if the vehicle is taken out of 4l (low) range, or the ignition switch is turned to the lock position. Electronic sway bar disconnect — if equipped your vehicle may be equipped with an electronic discon- necting stabilizer/sway bar. This system allows greater front s...

  • Page 301

    When activation conditions are not met. The stabilizer/ sway bar should remain in on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard-surfaced roads or at speeds above 18 mph (29 km/h); you may lose control of the vehicle, which could result...

  • Page 302

    Warning! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your loca...

  • Page 303

    2. Remove one bolt from the underside of the vehicle. 3. Remove the side step assembly. The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-pack...

  • Page 304

    Your vehicle’s steering, handling and traction. Control- ling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture. Avoid sudden accelerations, turns or braking. In most cases, there are no road signs, po...

  • Page 305

    Using light brake pressure with light throttle will keep the vehicle from jerking or lurching. This technique is also used when you need to stop and restart a vehicle on a steep incline. Driving in snow, mud and sand snow in heavy snow or for additional control and traction at slower speeds, shift t...

  • Page 306

    Entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck. Sand soft sand is very difficult to travel through with full tire pressure. When crossing soft, sandy spots in a trail, maintain your vehicle’s momentum...

  • Page 307

    Forward until it makes contact with the object. Apply the throttle lightly while holding a light brake pressure and ease the vehicle up and over the object. Warning! Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle. Using a spotter th...

  • Page 308

    Vehicle’s mobility. Approach these obstacles at a 45- degree angle and let each tire go through the obstacle independently. You need to use caution when crossing large obstacles with steep sides. Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle ...

  • Page 309

    Of the high point when you let the vehicle down. You can also try rocking the vehicle or winching the vehicle off the object. Caution! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill climbing hill climbing requires good judgment and a good under- standin...

  • Page 310

    Slightly to bring all four tires back on the ground. As you approach the crest of the hill, ease off the throttle and slowly proceed over the top. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than...

  • Page 311

    Driving across an incline if at all possible, avoid driving across an incline. If it is necessary, know your vehicle’s abilities. Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover. Make sure the surface has good tra...

  • Page 312

    Designated and approved. You should tread lightly and avoid damage to the environment. You should know your vehicle’s abilities and be able to recover it if something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake...

  • Page 313

    Muddy waters; check for hidden obstacles. Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary. The key to a safe crossing is the water depth, current and bottom conditions. On soft bottoms, the vehicle will sink in, effectively increas- ing the water lev...

  • Page 314

    Should never attempt to cross flowing water which is deeper than the vehicle’s running ground clearance. Even the slowest current can push the heaviest vehicle down- stream and out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed, det...

  • Page 315

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, brake ro- tors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You...

  • Page 316

    System. This noise should be considered normal, and it does not in any way damage the steering system. Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the ...

  • Page 317

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in section 7 for the correct fluid type. Parking brake note: this vehicle is not equipped with a self- adjusting parking br...

  • Page 318

    Be sure the parking brake is firmly set when parked, and the shift lever is in the park position (automatic trans- mission), or reverse, or first gear (manual transmis- sion). When parking on a hill, you should apply the parking brake before placing the shift lever in park; otherwise, the load on th...

  • Page 319

    Computer to modulate hydraulic pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces. All vehicle wheels and tires must be the same size and type, and tires must be properly inflated to produce accurate signals for the computer. Warning! Significant over or under-inflation o...

  • Page 320

    Warning! (continued) • the anti-lock brake system (abs) cannot prevent the natural laws of physics from acting on the vehicle, nor can they increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent...

  • Page 321

    Together to enhance vehicle stability and control in vari- ous driving conditions, and are commonly referred to as esp. Anti-lock brake system (abs) this system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wh...

  • Page 322

    System functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not ...

  • Page 323

    Hill start assist (hsa) the hsa system is designed to assist the driver when starting a vehicle from a stop on a hill. Hsa will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply th...

  • Page 324

    • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in reverse gear). Warning! There may be situations on minor hills (i.E., less than 8%), with a loaded vehicle, or while pulling a trailer where the system will not activate ...

  • Page 325

    Towing with hsa hsa will provide assistance when starting on a grade when pulling a trailer. Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough...

  • Page 326

    3. With the engine running, the brake applied, and the clutch out, rotate the steering wheel 180° counterclock- wise from center. 4. Press the esp off switch four times within twenty seconds. 5. Rotate the steering wheel 360° clockwise (180° clock- wise from center). 6. Cycle ignition switch off the...

  • Page 327

    Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. Electronic roll mitigation (erm) cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or ...

  • Page 328

    The “esp/tcs indicator light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Warning! The electronic stability program (esp) cannot pre- vent the natural laws of phys...

  • Page 329

    Esp function normally. This mode is intended to be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than esp would normally allow is required to gain traction. To turn esp on again, momen- tarily press the esp off switch. This will restore the normal “esp on” mode ...

  • Page 330

    “compass and mini-trip computer — if equipped” in section 4 of this manual. To turn esp on again, momen- tarily press the esp off switch. This will restore the normal “esp on” mode of operation. Note: • the esp system will change to “partial off” mode if the vehicle speed exceeds 40 mph (64 km/h). A...

  • Page 331

    Returns but tcs remains off. When the vehicle speed drops below 35 mph (40 km/h), the esp system shuts off. The esp is off at low vehicle speeds in 4l range so that it will not interfere with off-road driving, but the esp function returns to provide the stability feature at speeds above 40 mph (48 k...

  • Page 332

    Esp and defeat the functionality of the esp switch. Repeating the procedure will return the system to normal esp operation and restore esp switch functionality al- lowing esp “partial” or “off” modes. Warning! With esp in the permanent disable mode, enhanced vehicle stability offered by the esp and ...

  • Page 333

    9. Turn the steering wheel back to center. 10. Press and hold the esp off button for seven seconds. 11. Cycle the ignition key to off. After performing the esp disable procedure correctly, “esp off” will be displayed in the odometer for approxi- mately 12 seconds each time the ignition is moved to o...

  • Page 334

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 335

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 336

    • temporary spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards,...

  • Page 337

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 338

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 339

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 340

    Tire loading and tire pressure tire placard location tire placard location (two-door models) tire placard location (four-door models) 338 starting and operating.

  • Page 341

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 342

    Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx kg or xxx lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined...

  • Page 343

    5 starting and operating 341.

  • Page 344

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 345

    Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance and results in higher fuel consumption. R...

  • Page 346

    Tire pressure should be checked and adjusted as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated ev...

  • Page 347

    Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter. Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire infla...

  • Page 348

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 349

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 350

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep unmounted tires in a cool, dry place with ...

  • Page 351

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 352

    Tire chains install chains on rear tires only. Tire chains may be installed on all models except the sahara and rubicon. Follow these recommendations to guard against damage and excessive tire and chain wear: • use chains on p225/75r16 tires only. P255/75r17, p255/70r18, and lt255/75r17 tires do not...

  • Page 353

    The suggested rotation method is the “forward-cross” shown in the following diagram. Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The tire pressure will vary with tem...

  • Page 354

    Off until the tire pressure is at or above recommended cold placard pressure. Once the “tire pressure monitor- ing telltale light” has been illuminated, the tire pressure must be increased to the recommended cold placard pressure in order for the “tire pressure monitoring telltale light” to be turne...

  • Page 355

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 356

    The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • tire pressure monitoring telltale light a tire pressure monitoring sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare...

  • Page 357

    2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpm sensors. Note: • if your vehicle is equipped with a matching full-size s...

  • Page 358

    Vehicle in place of the spare tire, the tpms will update automatically and the “tire pressure monitoring tell- tale light” will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes a...

  • Page 359

    Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. Over 40 auto manufacturer’s worldwide have issued and endorsed consistent gasoline specifications (t...

  • Page 360

    Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While mtbe is an oxygenate made from methanol, it does not have the negative effects of methanol. E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 1...

  • Page 361

    Vehicle. The mmt content of gasoline may not be indi- cated on the gasoline pump, therefore, you should ask your gasoline retailer if the gasoline contains mmt. It is even more important to look for gasoline without mmt in canada, because mmt can be used at levels higher than those allowed in the un...

  • Page 362

    Caution! (continued) • the use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsi...

  • Page 363

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the swing gate closed when driving your v...

  • Page 364

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 365

    Loose fuel filler cap message after fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged. If the system detects a malfunction, the “gascap” message will display in the odometer display. Tighten the gas cap until a...

  • Page 366

    Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the gawr of each axle is not exceeded. Each axle’s gawr is determined by the components in the system with the lowest load carrying capacity (a...

  • Page 367

    The entire vehicle should first be weighed on a commer- cial scale to ensure that the gvwr has not been ex- ceeded. The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may...

  • Page 368

    Common towing definitions the following trailer towing-related definitions will as- sist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and trailer tongue weight. The t...

  • Page 369

    Trailer tongue weight (tw) the trailer tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal area the frontal area is the max...

  • Page 370

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in an accident. • weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputabl...

  • Page 371

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmis- sion axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3...

  • Page 372

    Engine/ transmis- sion axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ manual 3.21 two– door sahara model (4wd) 5,231 lbs (2 373 kg) 25 sq ft (2.32 sq m) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/ manual 3.73 two– door saha...

  • Page 373

    Engine/ transmis- sion axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ manual 4.10 2–door rubicon model (4wd) 6,365 lbs (2 887 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/ automatic 4.10 two– door rub...

  • Page 374

    Engine/ transmis- sion axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ automatic 3.73 four– door sahara model (2wd) 7,893 lbs (3 580 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ manual 3.21 four– d...

  • Page 375

    Engine/ transmis- sion axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ manual 3.21 four– door sahara model (4wd) 5,625 lbs (2 551 kg) 32 sq ft (2.97 sq m) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/ manual 3.73 four– door sa...

  • Page 376

    Engine/ transmis- sion axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ manual 4.10 four– door rubicon model (4wd) 8,248 lbs (3 741 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ automatic 4.10 four– ...

  • Page 377

    Trailer and trailer tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely s...

  • Page 378

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information placard in the “tire...

  • Page 379

    Warning! (continued) • when hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or dam- age to the brakes, axle, engine, transmission, steer- ing, suspension, chassis structure or tires. • safety chains must always be ...

  • Page 380

    Warning! (continued) 4. Tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing requirements — tires − do not attempt to tow a trailer while using a compact sp...

  • Page 381

    − an electronically-actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge-actuated brake system, an electronic brake controller is not required. − trailer brakes are recommended for trailers over...

  • Page 382

    Towing requirements — trailer lights & wiring whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The trailer tow package will include a four–pin wiring harness. Use a factory-approved trailer harness and connecto...

  • Page 383

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Automatic transmission the drive range can ...

  • Page 384

    Electronic speed control — if equipped − do not use in hilly terrain or with heavy loads. − when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − use speed control in flat terrain and with light loads to maxim...

  • Page 385

    Towing – four-wheel drive models note: the transfer case must be shifted into n (neu- tral), automatic transmission must be shifted into park, and manual transmission must be placed in gear (not in neutral) for recreational towing. Shifting into neutral (n) warning! You or others could be injured if...

  • Page 386

    7. Release the brake pedal and ensure that there is no vehicle movement. 8. Turn the engine off and turn the ignition switch to the acc position. 9. Shift the automatic transmission into park. 10. Apply the parking brake. 11. Attach the vehicle to the tow vehicle with the tow bar. 12. Release the pa...

  • Page 387

    5. Shift the automatic transmission into drive or release the clutch on manual transmissions. Note: when shifting out of transfer case n (neutral) on automatic transmission-equipped vehicles, turning the engine off may be required to avoid gear clash. Caution! • do not use a bumper-mounted clamp-on ...

  • Page 389: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . 388 䡵 if your engine overheats . . . . . . . . . . . . . . . . 388 䡵 jacking and tire changing . . . . . . . . . . . . . . . 389 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 390 ▫ spare tire ...

  • Page 390

    Hazard warning flasher the hazard warning flasher switch is located on the lower switch bank below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 391

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 392

    Jack location the jack and lug wrench are located in the rear storage compartment. Refer to “storage” in section 3 of this manual. Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwi...

  • Page 393

    2. Set the parking brake. 3. Shift the automatic transmission into park, or a manual transmission into reverse. 4. Turn the ignition to lock. 5. Turn on the hazard warning flasher. 6. Block both the front and rear of the wheel diagonally opposite of the jack- ing position. For example, if changing t...

  • Page 394

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor tr...

  • Page 395

    5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle...

  • Page 396

    Wheel nut tightness is 95 ft lbs (130 n·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Remove the jack assembly and wheel blocks. Warning! A loose tire or jack, thrown forward in a collision or hard stop, cou...

  • Page 397

    1. Remove all metal jewelry such as watch bands or bracelets which might make an unintended electrical contact. 2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, shift the automatic transmission into park, or the manual t...

  • Page 398

    Warning! Any procedure other than above could result in: • personal injury caused by electrolyte squirting out the battery vent. • personal injury or property damage due to battery explosion. • damage to the charging system of the booster vehicle or of the immobilized vehicle. • you should not try t...

  • Page 399

    Warning! • chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. Caution! Tow hooks are for emergency use only, to rescue a vehicle str...

  • Page 401: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.8l . . . . . . . . . . . . . . 401 䡵 onboard diagnostic system — obd ii . . . . . . 402 ▫ loose fuel filler cap message . . . . . . . . . . . 402 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 402

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 421 ▫ automatic transmission — if equipped . . . . 423 ▫ hydraulic clutch fluid — manual transmission . . . . . . . . . . . . . . . . . . . . . . . 426 ▫ manual transmission — if equipped . . . . . . 426 ▫ transfer case — if equipped . . ....

  • Page 403

    Engine compartment – 3.8l 1 — integrated power module 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — automatic transmission dipstick 9 — air cleaner filter 4 — engine oil fill 10 — coolant pressure cap 5 — engine oil dipstick 11 — power steering fluid reservoir 6 — brake flu...

  • Page 404

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 405

    The message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil off. Emissions inspection and maintenance programs in some localities, it may be a le...

  • Page 406

    5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 407

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any pro...

  • Page 408

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 409

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” in section 8 for information on this system. Note: under no circumstances should oil change intervals exceed 6,000 miles (10 000 km...

  • Page 410

    Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil fi...

  • Page 411

    Engine oil filter selection all of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. Mopar 威 engine ...

  • Page 412

    Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and are identified on the battery case. Also, if a “fast charger”...

  • Page 413

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 414

    Hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of...

  • Page 415

    Some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades; this will help blade perfor- mance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating informa...

  • Page 416

    Caution! The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. Under normal operating conditions, the catalyti...

  • Page 417

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situati...

  • Page 418

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 419

    Cooling system — drain, flush, and refill if the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant ...

  • Page 420

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol based engine coolant (anti- freeze). Use of propylene glycol base engine cool- ant (antifreeze) is not recommended. Adding engine coolant your vehicle has been built with an improved engine coolant (antifreeze) t...

  • Page 421

    Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that ...

  • Page 422

    To remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Engine coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and war...

  • Page 423

    Engine coolant (antifreeze) needs to be added, the contents of the coolant recovery bottle must also be protected against freezing. • if frequent engine coolant (antifreeze) additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should ...

  • Page 424

    Power disc brakes disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake master cylinder the fluid level in the master cylinders should be checked whenever the vehicle is serviced. If ...

  • Page 425

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 426

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 427

    Adding any quantity of oil through the dipstick tube, wait a minimum of two minutes for the oil to fully drain into the transmission before rechecking the fluid level. Note: if it is necessary to check the transmission below the operating temperature, the fluid level should be between the two cold (...

  • Page 428

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Hydraulic clutch fluid — manual transmission the clutch hydraulic system is a sealed maintenance-free system. In the e...

  • Page 429

    Adding fluid fluid should be added only at filler hole until fluid begins to run out of the hole. Drain first remove the fill plug (b), then the drain plug (c). The recommended tightening torque for the drain and fill plugs is 15 to 25 ft lbs (20 to 34 n·m). Caution! When replacing the plugs, do not...

  • Page 430

    Selection of lubricant use only manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in this section for the correct fluid type. Maintenance after off-road driving after extended operation in mud, sand or water, or similar dirty conditions, have your brake drums, brake ...

  • Page 431

    Corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The fol...

  • Page 432

    • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8...

  • Page 433

    • use mopar威 touch-up paint or equivalent on scratches or chips as soon as possible. Your authorized dealer has touch-up paint to match the color of your vehicle. Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with a mil...

  • Page 434

    Interior care use mopar 威 total clean or equivalent to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar 威 total clean or equiva- lent, then mopar 威 spot & stain remover or equivalent if absolutely necessary. Do not use harsh c...

  • Page 435

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol co...

  • Page 436

    • be especially careful when washing the windows by following the directions for “care of fabric top windows.” washing — use mopar 威 car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use mopar 威 con- vertible cloth top cleaner o...

  • Page 437

    Care of fabric top windows caution! Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is taken by following these directions: 1. Never use a dry cloth to remove dust. Instead, use a microfiber towel or soft cotton cloth moistened with cold or warm, clea...

  • Page 438

    If a stuck zipper slide is experienced, work the mopar 威 soft top zipper cleaner and lubricant or equivalent into the zipper slide. Several applications may be required before the zipper comes free. 6. Never paste stickers, gummed labels or any tape to the windows. Adhesives are hard to remove and m...

  • Page 439

    Cavity cartridge fuse mini fuse description j4 25 amp natural driver door node j5 25 amp natural passenger door node j6 40 amp green anti-lock brake sys- tem (abs) pump feed/esp j7 30 amp pink anti-lock brake sys- tem (abs) valve feed/esp j8 — — j9 40 amp green pzev sec motor feed/flex fuel j10 30 a...

  • Page 440

    Cavity cartridge fuse mini fuse description j21 20 amp blue front/rear washer j22 — spare m1 15 amp blue center high-mounted stop light (chmsl)/ switch stop lamp feed m2 20 amp yellow relay trailer lighting (stop) m3 20 amp yellow frt/rear axle locker relay m4 — — m5 — — m6 20 amp yellow power outle...

  • Page 441

    Cavity cartridge fuse mini fuse description m11 10 amp red (ignition off draw) iod-hvac/atc, mw sensr, under- hood lamp (uh lmp) m12 30 amp green amplifier (amp) m13 20 amp yellow ignition off draw— cabin compartment node (iod-ccn), wireless control module (wcm), si- ren, multifunction control switc...

  • Page 442

    Cavity cartridge fuse mini fuse description m16 10 amp red occupant restraint controller (orc) m17 15 amp blue left tail/license/ park lamp (lt-tail/ lic/prk lmp) m18 15 amp blue right tail/park/run lamp (rt-tail/ prk/run lmp) m19 25 amp natural auto shut down (asd #1 and #2) m20 15 amp blue cabin c...

  • Page 443

    Cavity cartridge fuse mini fuse description m30 15 amp blue wiper motor frt, j1962 diagnostic feed m31 20 amp yellow backup lamps (b/u lamps) m32 10 amp red occupant restraint controller (orc), tt europe m33 10 amp red next generation con- troller (ngc), global powertrain engine controller (gpec) ca...

  • Page 444

    Cavity cartridge fuse mini fuse description m38 25 amp natural lock/unlock motors (lock/unlock mtrs) caution! • when installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrat...

  • Page 445

    • or, disconnect the negative cable from the battery. • anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubricat...

  • Page 446

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamp 1. Open hood and support u...

  • Page 447

    Front park/turn signal 1. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counterclockwise and remove from housing. Pull the b...

  • Page 448

    Rear tail, stop, turn signal, and backup lamp 1. Remove the two inboard screws attaching the tail light housing to the body. Do not remove the outer screws at any time. 2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the appropri...

  • Page 449

    Fluid capacities u.S. Metric fuel (approximate) — two door models 18.5 gallons 70 liters fuel (approximate) — four door models 22.5 gallons 85 liters engine oil with filter 3.8 liter engine 6 quarts 5.7 liters cooling system * 3.8 liter engine (mopar 威 antifreeze/engine coolant 5 year/100,000 mile f...

  • Page 450

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chrysl...

  • Page 451

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid or equivalent. Manual transmission mopar 威 manual transmission lubricant or equivalent (meeting the re- quirements of chrysler material standard ms-9224). Transfer case mopar 威 atf+4...

  • Page 453: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . . 452 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 452 ▫ required maintenance intervals . . . . . . . . . . 454 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 454

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 455

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first. Your dealer will reset the oil change indicator message after completing ...

  • Page 456

    At each oil change • change the engine oil filter. • inspect the brake hoses and lines. • check the manual transmission fluid level. Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals refer to the maintenance schedules on th...

  • Page 457

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 458

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # dea...

  • Page 459

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your veh...

  • Page 460

    36,000 miles (60,000 km) or 36 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 461

    48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 462

    60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings, replace if necessary. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ ch...

  • Page 463

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the en...

  • Page 464

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the en...

  • Page 465

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect and replace pcv valve if necessary.† ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change...

  • Page 466

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings,...

  • Page 467

    108,000 miles (180,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake lining...

  • Page 468

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace accessory drive belt(s). ❏ inspect the brake linings, replace if necessary. ❏ inspect exhaust system. ❏ inspect the ...

  • Page 469

    126,000 miles (210,000 km) or 126 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # ...

  • Page 470

    138,000 miles (230,000 km) or 138 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change th...

  • Page 471

    150,000 miles (250,000 km) or 150 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your ...

  • Page 472

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 473: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473 ▫ prepare for the appointment . . . . . . . . . . . 473 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 473 ▫ be reasonable with r...

  • Page 474

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 479 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 479 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 479 ▫ temperature grades . . . . . . . . . . . . . . . . . . 48...

  • Page 475

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 476

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 477

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 478

    Has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. Warning! Engine exhaust, some of its constituents, and certa...

  • Page 479

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 480

    • service manuals these comprehensive service manuals provide the in- formation that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler llc ve- hicles. A complete working knowledge of the vehicle, system, and/or c...

  • Page 481

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 482

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 483: Index

    Index 10

  • Page 484

    Abs (anti-lock brake system) . . . . . . . . . . . . 203,316 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 air cleaner, engine (engine air cleaner filter) . . . 409 air conditioner maintenance . . . . . . . . . . . . . . . 410 air conditioning . . . . . . . . . . . . . . . . ...

  • Page 485

    Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 emergency starting . . . . . . . . . . . . . . . . . . . . . 394 keyless transmitter replacement (rke) . . . . . . . 23 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39,75 body mechanism lubrication . . ....

  • Page 486

    Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 264 clock . . . . . . . . . . . . . . . . . . . . . . . . 220,234,238,247 compact disc (cd) maintenance . . . . . . . . . . . . . 263 compass . . . . . . . . . ...

  • Page 487

    Disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 used coolant (antifreeze) . . . . . . . . . . . . . . . . 419 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 driver’s seat...

  • Page 488

    Fuel requirements . . . . . . . . . . . . . . . . . . 356,447 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . 394 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406,447 oil disposal . . . . . . . . . . . . . . . . . . . . . . . . . . 408 oil filter . . . . . . . . . ...

  • Page 489

    Fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 96,445 fold and tumble rear seat . . . . . . . . . . . . . . . . . . 88 folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . 91 folding windshield . . . . . . . . . . . . . . . . . . . . . . 186 four wheel drive . . . . . ...

  • Page 490

    Hard top, modular . . . . . . . . . . . . . . . . . . . . . . 115 hard top removal . . . . . . . . . . . . . . . . . . . . . . . 119 hazard warning flasher . . . . . . . . . . . . . . . . . . . 388 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 87 head rests . . . . . . . . . . ...

  • Page 491

    Jacking instructions . . . . . . . . . . . . . . . . . . . . . . 391 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . 394 key, programming . . . . . . . . . . . . . . . . . . . . . . . . 16 key, replacement . . . . . . . . . . . . . . . . . . . . . . . . 15 key, sentry (immobilizer)...

  • Page 492

    Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96,445 hazard warning flasher . . . . . . . . . . . . . . . . . 388 headlight switch . . . . . . . . . . . . . . . . . . . . . . . 95 headlights . . . . . . . . . ....

  • Page 493

    Maintenance schedule . . . . . . . . . . . . . . . . . . . . 452 malfunction indicator light (check engine) . . . . . . . . . . . . . . . . . . . . . . . 210,403 manual, service . . . . . . . . . . . . . . . . . . . . . . . . . 477 manual transmission . . . . . . . . . . . . . . . . . . 281,426 flui...

  • Page 494

    Oil pressure light . . . . . . . . . . . . . . . . . . . . . . . 201 onboard diagnostic system . . . . . . . . . . . . . . 402,403 operator manual (owner’s manual) . . . . . . . . . . . . 6 outside rearview mirrors . . . . . . . . . . . . . . . . . . 82 overheating, engine . . . . . . . . . . . . . ...

  • Page 495

    Shifting out of transfer case neutral (n) . . . . . 384 reformulated gasoline . . . . . . . . . . . . . . . . . . . . 357 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 release, hood . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 reminder, lights on . . . . . . . ....

  • Page 496

    Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 fold and tumble re...

  • Page 497

    Automatic transmission . . . . . . . . . . . . . . . . . 277 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . 278 engine block heater . . . . . . . . . . . . . . . . . . . . 281 engine fails to start . . . . . . . . . . . . . . . . . . . . 278 manual transmission . . . . . . . . . . . ...

  • Page 498

    Inflation pressures . . . . . . . . . . . . . . . . . . . . . 343 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 389,392 load capacity . . . . . . . . . . . . . . . . . . . . . 338,339 pressure monitor system (tpms) . . . . . . . . . . . 351 pressure warning light . . . . . . . . . . ...

  • Page 499

    Transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 maintenance . . . . . . . . . . . . . . . . . . . . . . . 423,426 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 range indicator . . . . . . . . . . . . . . . . . . . . . . . 206 shifting . . . . ....

  • Page 500

    Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 windshield defroster . . . . . . . . . . . . . . . . . . . . . . 76 windshield, folding . . . . . . . . . . . . . . . . . . . . . . 186 windshield washers . ....

  • Page 501

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 502

    121413 09 wrangler om.Indd 1 121413 09 wrangler om.Indd 1 3/11/08 9:26:49 am 3/11/08 9:26:49 am.