1. DL manuals
  2. Jeep
  3. Automobile
  4. 2009 Wrangler
  5. Owner's Manual

Jeep 2009 Wrangler Owner's Manual

Manual is about: Wrangler 2009

Summary of 2009 Wrangler

  • Page 1

    121413 09 wrangler om.Indd 1 121413 09 wrangler om.Indd 1 3/11/08 9:26:06 am 3/11/08 9:26:06 am.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefor. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be s...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the ...

  • Page 5: Introduction

    Introduction contents m introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m rollover warning . . . . . . . . . . . . . . . . . . . . . . . . 5 m how to use this manual . . . . . . . . . . . . . . . . . . 6 m warnings and cautions . . . . . . . . . . . . . . . . . . . 8 m vehicle i...

  • Page 6

    Introduction this is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so ta...

  • Page 7

    Note: after you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-train...

  • Page 8

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annuall...

  • Page 9

    Introduction 7 1.

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 11: Contents

    Things to know before starting your vehicle contents m a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . . 13 m steering wheel lock . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 21 ▫ to turn off “flash lights with lock” . . . . . . . 22 ▫ programming additional rke transmitters . . . 22 ▫ general information . . . . . . . . . . . . . . . . . . . . 24 ▫ battery replacement . . . . . . . . . . . . . . . . . . . 24 m re...

  • Page 13

    ▫ adjustable upper shoulder belt anchorage . . . 47 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . . 48 ▫ enhanced seat belt use reminder system (beltalert t) . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ▫ seat belts and pregnant women . . . . . . . . . . . 49 ▫ seat belt exte...

  • Page 14

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 15

    Manual transmission — if equipped 1. Turn the ignition switch to the acc (accessory) position. 2. Push the ignition key inward. 3. Turn the ignition key to the lock position, and remove the key. Warning! Leaving unattended children in a vehicle is danger- ous for a number of reasons. A child or othe...

  • Page 16

    To manually lock the steering wheel with the engine running, rotate the steering wheel one– half revolution from the straight ahead position, turn off the engine, and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To release the steering wheel lock inse...

  • Page 17

    During normal operation, after turning on the ignition switch, the vehicle security light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the vehicle security light begins to fla...

  • Page 18

    Caution! Always remove the sentry keys t from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit personal identification number (pin). Keep the pin in a secure location. This number is required for authorized ...

  • Page 19

    4. Insert a blank sentry key t into the ignition switch. Turn the ignition switch to the on position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the vehicle security light will stop flashing. To indicate that programming is complete, the vehicle security light will t...

  • Page 20

    Vehicle security alarm system — if equipped the vehicle security alarm system monitors the vehicle doors, swing gate, and ignition for unauthorized opera- tion. When the vehicle security alarm is activated, the system provides both audible and visible signals. The horn, headlights, and tail lights w...

  • Page 21

    To disarm the system to disarm the vehicle security alarm system, you will need to press the unlock button on the rke transmit- ter, or turn the ignition key to the on position. If something has triggered the vehicle security alarm in your absence, the horn will sound three times when you unlock the...

  • Page 22

    Note: the line of transmission must not be blocked with metal objects. To unlock the doors and swing gate press and release the unlock button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the unlock button is pressed, the illuminated entry will initiate...

  • Page 23

    4. Test this feature while outside of the vehicle, by pressing the lock/unlock button on the rke trans- mitter. Note: pressing the lock button while you are inside of the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm acti- vated will cause the alarm...

  • Page 24

    To turn off “flash lights with lock” note: the “flash lights with lock” feature can be turned on or off using the following steps: 1. Press the unlock button for 4 to 10 seconds. 2. While the unlock button is pressed, (after four seconds) press the lock button. Release both buttons. 3. Test the “fla...

  • Page 25

    2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the ignition key into the ignition. 4. Turn the ignition to the on position. Do not start the engine. 5. Press and hold the unlock button. 6. After holding th...

  • Page 26

    General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may...

  • Page 27

    2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the rke transmitter case, snap the two halves together. Note: if the rke transmitter is equipped...

  • Page 28

    Once the vehicle has started, the engine will run for 15 minutes. To cancel remote start, press the remote start button once. The parking lights will remain illuminated to indicate that the vehicle has remote started and the engine is running. The lights will turn off when the ignition is turned to ...

  • Page 29

    The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the vehicle security alarm is alarming,...

  • Page 30

    Upper half door window removal — if equipped 1. Grasp the half door window and pull upward. Upper half door window installation — if equipped 1. Grasp the half door window and line up pins into pockets in lower door. 2. Push down to ensure the half door window is fully seated. Front door removal 1. ...

  • Page 31

    2. Unplug the wiring harness connector under instru- ment panel by pressing the tab at the side of the connector and pulling to disconnect. Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This wi...

  • Page 32

    3. Unhook the door strap from the body hook. Be careful not to allow the door to swing fully open as the mirror may damage paint. 4. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the previous steps in the opposite order. R...

  • Page 33

    4. Unplug the wiring harness connector. 5. Unhook the door strap from the body hook. 6. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the previous steps in the opposite order. Things to know before starting your vehicle 31...

  • Page 34

    Door locks the vacuum fluorescent (vf) display located in the odometer area displays the word “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the vf display will show the word “door.” if any other act...

  • Page 35

    Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. (continued) warning! (continued) • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of...

  • Page 36

    Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. (continued) warning! (continued) • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of...

  • Page 37

    5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h). Automatic unlock doors on exit programming the “automatic unlock doors on exit” feature can be enabled or disabled as follows: 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between...

  • Page 38

    Automatic door locks programming the “automatic door locks” feature can be enabled or disabled as follows: 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between lock and on and then back to lock four times ending up in the lock position. 3. Depress the power door...

  • Page 39

    Window lockout switch (four-door models only) the window lockout switch (located between the win- dow switches) allows you to disable the rear window switches that are located on the back of the center floor console. To disable the window controls, press the win- dow lockout button downward. To enab...

  • Page 40

    Rear power windows (four-door models only) the rear passenger window switches are located on the back of the center floor console. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting ...

  • Page 41

    If the trip/reset button is pressed while the vf warnings are being displayed, the vf display will revert back to only displaying the odometer/trip odometer mileage. The swing gate can be unlocked by using the key, remote keyless entry (rke) key fob, or by activating the power door lock switches loc...

  • Page 42

    Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flip-up window clos...

  • Page 43

    Warning! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up prope...

  • Page 44

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat using a seat belt properly. • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bo...

  • Page 45

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” pulling out the lap/shoulder belt latch plate inserting latch plate into buckle things to know before starting your vehicle 43 2.

  • Page 46

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is loose will not protect you as well. In a sudden stop you ...

  • Page 47

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt cannot do its job as well. In a collision ...

  • Page 48

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protecti...

  • Page 49

    Warning! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seatback is in the fully upright and locked position when occupied. If the rear seatback is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, th...

  • Page 50

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 51

    Beltalert t will continue to chime and flash the seat belt warning light for 96 seconds or until the driver’s seat belt is buckled. Beltalert t will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). Beltalert t can be...

  • Page 52

    Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its low...

  • Page 53

    Note: the front airbags are certified to the federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity. If the vehicle is equipped with side airbags...

  • Page 54

    Note: airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer func...

  • Page 55

    The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is so equipped, the side airbag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisio...

  • Page 56

    2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the ...

  • Page 57

    Airbag system components the airbag system consists of the following: • occupant restraint control (orc) module • airbag warning light • driver airbag • passenger airbag • front seat-mounted side airbags (if equipped) • steering wheel and column • instrument panel • interconnecting wiring • knee imp...

  • Page 58

    • also, the orc turns on the airbag warning light for six to eight seconds for a self-check when the ignition is first turned on. After the self-check, the airbag warning light will turn off. If the orc detects a malfunction in any part of the system, it turns on the airbag warning light either mome...

  • Page 59

    • the side impact (srs) seat-mounted side airbags (if equipped) are designed to activate only in certain side collisions. The orc determines if a side collision is severe enough to require the side airbags to inflate. The orc monitors the readiness of the electronic parts of the system whenever the ...

  • Page 60

    If you do have a collision which deploys the airbags, any or all of the following may occur: • the nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those...

  • Page 61

    Enhanced accident response feature if the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. The hazard lights will flash and the fuel will be cut off to the engine. In addition, after the vehicle has stoppe...

  • Page 62

    Note: perchlorate material – special handling may ap- ply, see www.Dtsc.Ca.Gov/hazardouswaste/perchlorate. Airbag warning light you will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occ...

  • Page 63

    Investigations may be requested by customers, insurance carriers, government officials, and professional crash researchers, such as those associated with universities, and with hospital and insurance organizations. In the event that an investigation is undertaken by chrysler llc (regardless of initi...

  • Page 64

    • 9time9 of airbag deployment (in terms of ignition cycles and vehicle mileage) • airbag deployment level (if applicable) • impact acceleration and angle • seat belt status • brake status (service and parking brakes) • accelerator status (including vehicle speed) • engine control status (including e...

  • Page 65

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any chi...

  • Page 66

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward facing infant restraint shou...

  • Page 67

    The retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. For additional information, refer to 9automatic locking mode9 ear- lier in this section. • in the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buc...

  • Page 68

    Vehicle by the lap/shoulder belt or the latch child restraint anchorage system (refer to latch — child seat anchorage system in this section). The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If...

  • Page 69

    Note: to reset this feature you must let all of the belt webbing return into the retractor. You will not be able to pull out more webbing until all of the webbing has been returned back into the retractor. Installing the child restraint system we urge you to carefully follow the directions of the ma...

  • Page 70

    Latch — child seat anchorage system (lower anchors and tether for children) your vehicle’s rear seat is equipped with the child restraint anchorage system called latch. The latch system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the ...

  • Page 71

    The rear seating positions have lower anchorages that are capable of accommodating latch-compatible child seats having flexible, webbing-mounted lower attach- ments. Child seats with fixed lower attachments must be installed in the outboard positions only. Regardless of the specific type of lower at...

  • Page 72

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch anchorages (two-door models) latch anchorages (four-door models) 70 things to know before starting your vehicle.

  • Page 73

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means for adjusting the tension of the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also b...

  • Page 74

    A hook for attachment to the tether strap anchorage, and a means for adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, attach the lower hooks ...

  • Page 75

    If the seat belt has an automatic locking retractor, it will have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is fully extended from the retractor....

  • Page 76

    Route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head rest, and attach the hook to the tether anchor located on the back of the seat. Warning! An incorrectly anchored teth...

  • Page 77

    Engine break-in recommendations a long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration ...

  • Page 78

    Safety tips exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co) follow the safety tips below. • do not inhale exhaust gases. They contain...

  • Page 79

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have b...

  • Page 80

    Safety checks you should make outside the vehicle tires examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires (includ- ing spare) for pr...

  • Page 81: Contents

    Understanding the features of your vehicle contents m mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 83 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . . 84 m hands–free communication (uconnectt) . . . . ...

  • Page 82

    M lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 ▫ multifunction lever . . . . . . . . . . . . . . . . . . . . 95 ▫ parking lights, instrument panel lights and headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 96 ▫ lights-on reminder . . . . . . . . . . . . . . ...

  • Page 83

    M electrical power outlet . . . . . . . . . . . . . . . . . . 105 ▫ electrical outlet use with engine off . . . . . . 106 m cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 107 ▫ front cupholders . . . . . . . . . . . . . . . . . . . . 107 ▫ rear cupholders . . . . . . . . . . . . . . ...

  • Page 84

    M soft top (four-door models) . . . . . . . . . . . . . . 151 ▫ folding down the soft top . . . . . . . . . . . . . 154 ▫ putting up the soft top . . . . . . . . . . . . . . . 164 m sunrider (two-door models) — if equipped . . . 176 m sunrider (four-door models) — if equipped . . 180 m folding winds...

  • Page 85

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward...

  • Page 86

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! • vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they ...

  • Page 87

    Hands–free communication (uconnect t ) this feature is not available on two–door or four–door models. Voice recognition button (uconnect t hands-free phone) when you press this button, a “not equipped with uconnect” message will display on your radio screen. Phone button (uconnect t hands-free phone...

  • Page 88

    Seats front seat adjustment move seat forward or rearward by lifting the lever. Be sure the latch is fully engaged. Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and yo...

  • Page 89

    Front seatback recline lean forward before lifting the handle, then lean back to the desired position and release the handle. Lift the handle to return the seatback to an upright position. Seat height adjustment recline lever understanding the features of your vehicle 87 3.

  • Page 90

    Front easy entry seats (two-door models) push the lever on the seatback rearward (toward the rear of the vehicle) to tilt the entire seat forward. To return the seat to a sitting position, rotate the seatback upright until it locks then push the seat rearward until the track locks. Easy entry lever ...

  • Page 91

    Note: • the front passenger seats have a full recliner memory, which will allow the seatback to be returned to its original position. • the front passenger seats have a track memory, which returns the seat to just past the halfway point of the track regardless of its original position. • the recline...

  • Page 92

    Also, be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. 1. Lift the seatback release lever and fold seatback for- ward. 2. Slowly flip the entire seat forward. 3. Return the seat to its normal position. 4. Raise the rear seatbac...

  • Page 93

    Removing the rear seat (two-door models) warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is no...

  • Page 94

    4. Press down on the release bar on each side, and pull the seat out and away from lower bracket. 5. Remove the seat from the vehicle. Replacing the rear seat (two-door models) reverse steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be seated in...

  • Page 95

    Note: • prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo area...

  • Page 96

    To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be ab...

  • Page 97

    Hood. You may have to push down slightly on the hood before pushing the handle. Insert the support rod into the slot on the hood panel. To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! I...

  • Page 98

    Parking lights, instrument panel lights and headlights turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the center portion of ...

  • Page 99

    Headlight dimmer switch push the multifunction lever away from you to switch the headlights to high beam. Pull the lever towards you to switch the headlights back to low beam. Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the stee...

  • Page 100

    Interior lights the overhead light will come on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the multifunction lever fully upward. The overhead light will automatically turn off in approxi- mately 20 minutes if a door is left open or the dimmer con...

  • Page 101

    When a door is open and the interior lights are on, rotating the dimmer control all the way down to the off detent will cause all the interior lights to turn off. This is also known as the 9party9 mode because it allows the doors to stay open for extended periods of time without discharging the vehi...

  • Page 102

    Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Intermittent wiper ...

  • Page 103

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is p...

  • Page 104

    Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic speed control — if equ...

  • Page 105

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the electronic speed control system off when you are not using it. To set at a...

  • Page 106

    Tapping the electronic speed control lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while electronic speed control is on, push down and hold set decel. Release the electronic speed control lever when the desired speed is reached, and the new speed will be set. Tapp...

  • Page 107

    To accelerate for passing depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using electronic speed control on hills note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills ...

  • Page 108

    The left side outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. The right side outlet has power available only when the ignition is on. This outlet will also operate a conven- tional ci...

  • Page 109

    Warning! (continued) • after the use of high-power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. • power outlets are designed fo...

  • Page 110

    Rear cupholders the rear cupholders are located on the back of the center console. Storage console storage compartment to lock or unlock, insert ignition key and turn. To open, press the latch and lift cover. Rear cupholders center console 108 understanding the features of your vehicle.

  • Page 111

    Rear storage compartment the rear storage compartment cover is held by a spring- loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: note: the rear storage compartment latch should not be used as cargo tie-down. 1. Flip up pull loop so it is perpendicu...

  • Page 112

    Hard top are to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top. Your vehicle warranty will not cover damage resulting from both tops remaining on the vehicle at the same time for extended periods of time. Removing the soft top 1. Locate and remove t...

  • Page 113

    4. Using a rubber mallet, carefully tap the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx t head driver. Re...

  • Page 114

    Installing the soft top note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (four for two-doo...

  • Page 115

    B. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the bows facing upward. C. Tap the knuckles on the side with a rubber mallet to reattach them to the metal pivot brackets. Understanding the features of your vehicle 113 3.

  • Page 116

    D. Screw the pivot screws back into place using a #t30 torx t head driver. Secure them until they are snug being careful not to cross-thread the screws or over- tighten. Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black me...

  • Page 117

    Freedom top three-piece modular hard top caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly c...

  • Page 118

    3. Turn rear l-shaped lock (located above shoulder belt anchorage). 4. Turn rear fasteners (knobs) (located on overhead speaker bar assembly) counterclockwise until they can be removed. 116 understanding the features of your vehicle.

  • Page 119

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove panel. To remove right panel, follow steps above except for step 2. Front panel(s) installation note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that the...

  • Page 120

    Front panel(s) installation only (with rear hard top removed) 1. Turn left and right panels over and move spacer block (located on rear of panel) upward 90 degrees. Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no over...

  • Page 121

    4. Remove the six torx t head screws that secure the hard top to the vehicle (along the interior bodyside) using a #40 torx t head driver. 5. Open swing gate all the way to ensure clearance of the rear window glass. Lift rear window glass. 6. Locate the wiring harness on the left rear inside corner ...

  • Page 122

    Caution! Make sure storage cap is installed to prevent foreign materials from entering washer tube and clogging system, and also to prevent fluid from being sprayed into the rear of the vehicle. 8. Disconnect the wire harness from the hard top by pressing the tab at the side of the connector and pul...

  • Page 123

    Rear hard top installation note: if the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. Install the hard top using the same steps for removal in reverse order. Note: the h...

  • Page 124

    Door frame removal (two-door models) 1. Unscrew and remove the door frame attachment knobs (two per side). Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the front of ...

  • Page 125

    4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. Understandin...

  • Page 126

    Door frame installation (two-door models) 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubbe...

  • Page 127

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame removal (four-door models) 1. Unscrew and remove the two forward most door frame attachment knobs. Warning! Use both hands to remove the door frames. The door frames will fold and could cause injur...

  • Page 128

    2. Place one hand on the upper rear and one hand on the upper front of the front door frame. 3. Pull the frame towards you with your front hand to remove the frame from the vehicle. 4. Unscrew and remove the remaining door frame at- tachment knob on the rear door frame. 126 understanding the feature...

  • Page 129

    5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame towards you with your rear hand to remove the frame from the vehicle. 6. Screw the knob back into the door frame and fold for storage. Store in a secure location. Warning! • never store the doo...

  • Page 130

    Door frame installation (four-door models) 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch ...

  • Page 131

    5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. Then, clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. Position the rear of the front door frame to lay on top o...

  • Page 132

    Soft top (two-door models) please visit the owners section of jeep.Com for instruc- tional videos. Caution! • the soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a struct...

  • Page 133

    Caution! (continued) • refer to “appearance care for fabric top models” in section 7 of this manual. It contains important information on cleaning and caring for your vehi- cle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing t...

  • Page 134

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — sail panel 9 — front retainer — quarter window 5 — plastic retainer 10 — bottom retainer — quarter window 132 understanding the features of your vehicle.

  • Page 135

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels understanding the features of your vehicle 133 3.

  • Page 136

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 137

    4. Release the header latches and leave the hooks in the loops on the windshield. 5. Open the swing gate. 6. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate bracket...

  • Page 138

    • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid s...

  • Page 139

    10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 11. As you begin to lower the top, fold the sail panels so that they rest on top of the soft to...

  • Page 140

    12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage. 13. Completely release the latches from the loops on the w...

  • Page 141

    14. Make sure the plastic sleeves are slid forward over the sunrider link (sunrider models only). 15. Unlatch the side bows from both door rails (sunrider models only). 16. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake lamp. Move to the...

  • Page 142

    Note: help from another person will ease this opera- tion. 17. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. When the top is completely down, position the drip rails so they make a “v-s...

  • Page 143

    Putting up the soft top 1 — header bow 6 — body side retainer 2 — 2– bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — sail panel 9 — front retainer — quarter window 5 — plastic retainer 10 — bottom retainer — quarter window understanding the features of your vehicle 141 3.

  • Page 144

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 142 understanding the features of your vehicle.

  • Page 145

    1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “door frame” in this section. 3. Make sure the plastic sleeve is slid rearward over sunrider link (sunrider models only). 4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (mi...

  • Page 146

    6. Make sure the sunrider bracket on the side bows latches to the door rails (sunrider models only). 7. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 8. If the swing gate brackets were removed, install them by hooking the rear edge of ...

  • Page 147

    9. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 10. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) towards the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to re...

  • Page 148

    11. To install the side windows, affix the window tem- porarily by attaching to the velcro t in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 12. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on...

  • Page 149

    13. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro t along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 150

    14. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 148 understanding the features of your vehicle.

  • Page 151

    15. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 16. Run the zipper fully around to the right side of the window. Understanding the features of your...

  • Page 152

    17. Grasp the swing gate bar and position it into the swing gate brackets. 18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 19. Open the doors and insert the roof retainers into the channels a...

  • Page 153

    20. Close the header latches and return the sun visors to their secured position. Soft top (four-door models) please visit the owners section of jeep.Com for instruc- tional videos. Caution! • the soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunti...

  • Page 154

    Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place. If temperature is 41°f (5°c) or below, do not attempt to put the top down or roll the rear or side curtains. Caution! • do not run a fabric ...

  • Page 155

    Warning! • do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the ve- hicle. • the fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants wi...

  • Page 156

    Folding down the soft top 1 — header bow 6 — body side retainer 11 — plastic retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 154 understanding the features of your vehicle.

  • Page 157

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels understanding the features of your vehicle 155 3.

  • Page 158

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 159

    4. Release the header latches and hooks from the loops on the windshield frame. 5. Open the swing gate. 6. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets....

  • Page 160

    • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid s...

  • Page 161

    10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 11. Fold the sail panels so that they rest on top of the soft top. Understanding the features o...

  • Page 162

    12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage. 13. Grasp the front side bow behind the header, and lift t...

  • Page 163

    14. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 15. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle, and move the material into two folds. Understanding the features of ...

  • Page 164

    16. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 17. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake lamp. Grasp the folded s...

  • Page 165

    18. Gently slide the side bows off the door frame track and lower the top down into the vehicle. Note: help from another person will ease this opera- tion. 19. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside...

  • Page 166

    Putting up the soft top 1 — header bow 6 — body side retainer 11 — plastic retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 164 understanding the features of your vehicle.

  • Page 167

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels understanding the features of your vehicle 165 3.

  • Page 168

    Note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section. 2. Undo the straps used to secure the top in the down position and store in se...

  • Page 169

    5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 6. Ensure that the top locks into sunrider locking mecha- nisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. Understanding the features of your veh...

  • Page 170

    8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Before attaching the header latches, be sure the top retainers above the doors do not get trapped between the top and the door frame. Also, make certain the feet at both ends of the 2–bow ...

  • Page 171

    10. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 11. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel...

  • Page 172

    12. Ensure straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow). A. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) towards the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) ...

  • Page 173

    13. To install the side windows, affix the window tem- porarily by attaching to the velcro t in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm). 14. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positio...

  • Page 174

    15. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro t along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 175

    16. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. Understanding the features of your vehicle 173 3.

  • Page 176

    17. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 18. Run the first zipper fully around to the right side of the window. 19. Grasp the swing gate bar...

  • Page 177

    21. Open the doors and insert the top retainers into the channels in the door frame above the doors, starting at the front and working toward the rear of the vehicle. 22. Ensure plastic retainer is tucked in properly at b-pillar, not pinching the seal. Understanding the features of your vehicle 175 ...

  • Page 178

    23. Close the header latches and return the sun visors to their secured position. Sunrider (two-door models) — if equipped note: if you are going to be driving faster than 40 mph (64 km/h) with the sunrider feature open, it is recom- mended that you remove the rear window of the vehicle. To open 1. ...

  • Page 179

    2. Unclip and move the sun visors to the side. 3. Release the header latches from the loops on the windshield frame. Understanding the features of your vehicle 177 3.

  • Page 180

    4. Slide the plastic sleeve forward. 5. Grasp the header and lift the top back. Make sure the material is folded back as shown. Note: the sunrider latch on the door rail should not be activated for sunrider use. If activated, the soft top must be reinstalled starting from the sail panels. 178 unders...

  • Page 181

    6. Locate straps to secure side bows. Wrap straps around bows as shown. Repeat on the other side. 7. Reposition sun visors. To close 1. Remove straps from side bows. 2. Unclip and move sun visors to the side. 3. Grasp the front header and pull to the front of the vehicle. 4. Hook header latches to t...

  • Page 182

    Sunrider (four-door models) — if equipped note: if you are going to be driving faster than 40 mph (64 km/h) with the sunrider feature open, it is recom- mended that you remove the rear window of the vehicle. To open 1. Above the front of the rear door, place finger up into the cutout in the plastic ...

  • Page 183

    3. Release the header latches from the loops on the windshield frame. 4. Grasp the front side bow behind the header, and lift the top. Understanding the features of your vehicle 181 3.

  • Page 184

    5. Fold back the front section of the top, and gently rest the header on top of the rear portion of the deck. 6. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle, and move the material into two folds. Ensure that the straps are securely stowed. 7. Close the ...

  • Page 185

    8. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro t to itself, use one strap on each side of the vehicle. To close perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to sag and may blo...

  • Page 186

    Raise the windshield and reinstall the side bars as soon as the task that required their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down...

  • Page 187

    Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assist in properly reinstalling side bars, mark the original locations prior to removing. 2. Remove the two top hex bolts (13 mm), and the one side hex bo...

  • Page 188

    Note: pull side bar out horizontally when removing. Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 5. Remove side bar assembly, and reattach sport ba...

  • Page 189

    7. Remove the windshield wiper arms by first pulling the wiper away from the windshield and out to the “lock” position. Unsnap the wiper arm nut caps, and remove retaining nuts. Lift the wiper arms off and store in center console or securely behind the rear seat. Note: it may be necessary to use a b...

  • Page 190

    Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach rear of side bar to sport bar. Refer to step 4 of “lowering windshield and removing side bars” earlier in this section. • reattach sport bar velcrot covering. 3. Attach front of side bar to windshield frame. • ...

  • Page 191

    5. Install the lower windshield plates with the six black round-headed torx t head screws (using a #40 torxt head driver) on each side of the base of the windshield. 6. Reinstall wiper arms. Rear window features — hard top only rear window wiper/washer — if equipped a rotary ring switch on the contr...

  • Page 192

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at. Adding washer fluid the fluid reservoir for the windshield washers and...

  • Page 193

    The defroster will automatically turn off after about ten minutes. For five more minutes of operation, press the switch again. To prevent excessive battery drain, use the defroster only when the engine is operating. Caution! Use care when washing the inside of the rear window to prevent damage to he...

  • Page 195: Contents

    Understanding your instrument panel contents m instrument panel and controls . . . . . . . . . . . . 196 m instrument cluster . . . . . . . . . . . . . . . . . . . . . 197 m instrument cluster description . . . . . . . . . . . . 198 m compass and trip computer — if equipped . . 210 ▫ control buttons...

  • Page 196

    ▫ operating instructions — voice recognition system (vr) — if equipped . . . . . . . . . . . . . 230 ▫ operating instructions — hands-free communication (uconnect t) — if equipped. . . . . . . . . . . . . . . . . . . . . . . 231 ▫ clock setting procedure . . . . . . . . . . . . . . . . 231 m sales c...

  • Page 197

    M climate controls . . . . . . . . . . . . . . . . . . . . . . 247 ▫ manual heater only . . . . . . . . . . . . . . . . . . 247 ▫ manual air conditioning and heating system — if equipped . . . . . . . . . . . . . . . . . 250 ▫ air conditioning . . . . . . . . . . . . . . . . . . . . . 253 ▫ operatin...

  • Page 198

    Instrument panel and controls 1 - air outlet 6 - climate controls 2 - instrument cluster 7 - power outlet 3 - horn 8 - lower switch bank 4 - radio 9 - auxiliary power outlet 5 - glove compartment 196 understanding your instrument panel.

  • Page 199

    Instrument cluster understanding your instrument panel 197 4.

  • Page 200

    Instrument cluster description 1. Fuel gauge the pointer shows the level of fuel in the fuel tank. Note: when the ignition switch is turned to off, the fuel gauge, voltmeter, oil pressure and temperature gauges may not show accurate readings. When the engine is not running, turn the ignition switch ...

  • Page 201

    7. Seat belt reminder light a warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on for about six seconds, until it times out. 8. Turn signal indicators the arrows will flash with the exterior turn sign...

  • Page 202

    Indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indica...

  • Page 203

    Vehicles equipped with the anti-lock brake system (abs), are also equipped with electronic brake force distribution (ebd). In the event of an ebd failure, the brake warning light will turn on along with the abs light. Immediate repair to the abs system is required. Operation of the brake warning lig...

  • Page 204

    14. Rear axle lock indicator — if equipped this light indicates when the rear axle lock has been activated. 15. Tachometer indicates the engine speed in revolutions per minute (rpm). Caution! Do not operate the engine with the tachometer pointer in the red area. Engine damage will occur. 16. Engine ...

  • Page 205

    Caution! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear continuo...

  • Page 206

    21. Odometer / trip odometer reset button press this button to change the display from odometer to either of the two trip odometer settings. Trip a or trip b will appear when in the trip odometer mode. Press and hold the button for two seconds to reset the trip odometer to 0 miles or kilometers. The...

  • Page 207

    Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

  • Page 208

    U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after t...

  • Page 209

    1. Turn the ignition switch to the on position (do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator...

  • Page 210

    (esp) becomes active. The esp/tcs indicator light also flashes when tcs is active. Be sure to adapt your speed and driving to the prevailing road conditions. If the esp/tcs indicator light is on solid, the esp system has been turned off by the driver or a temporary condition exists that will not all...

  • Page 211

    30. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is run- ning, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition key when the ve...

  • Page 212

    Compass and trip computer — if equipped this feature, located on the instrument cluster (speedom- eter and tachometer), displays information on outside temperature, compass direction, and trip information. Control buttons press and release the left button (on the instrument cluster) to access the co...

  • Page 213

    Estimated range (dte) this display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is based on the most recent trip informa- tion: (average fuel economy) x (fuel remaining) this display cannot be reset. Elapsed time (et) this display s...

  • Page 214

    Compass calibration the compass on your vehicle will automatically calibrate when new, and will continuously adjust itself over the life of the vehicle. If the cal indicator is on (or flashing), drive slowly (under 10 mph) in an open area until the cal indicator is off. Note: magnetic and battery po...

  • Page 215

    1. First enter the variance mode. Press and hold the left button (located on the instrument cluster) for approxi- mately 10 seconds to enter the variance mode, and release the button when the var (compass variance) symbol appears. 2. The current variance value will also be displayed. Once in the var...

  • Page 216

    To increment the zone. The default is zone 8. After zone 15, the values will wrap around to zone 1. When the correct zone is displayed (per the compass variance zone map) for the zone that the vehicle is located in, wait for about five seconds, then the trip computer will store the variance value in...

  • Page 217

    Sales code req — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) note: the radio sales code is located on the lower right side of your radio faceplate. Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/v...

  • Page 218

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Scan button pressing the scan button causes the tuner to search for the next listenable stat...

  • Page 219

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save the time change. 5. To exit, press any button/knob or wai...

  • Page 220

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 221

    Program type 16-digit character display jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r & b sports sports talk talk prog...

  • Page 222

    Note: turn the tune/scroll control knob to scroll through the entries. Push the audio/select button to select an entry and make changes. • dvd enter - when the disc is in dvd menu mode, selecting dvd enter will allow you to play the current highlighted selection. Use the remote control to scroll up ...

  • Page 223

    • ves™ ch1/ch2 - allows the user to change the mode of either the ir1 or ir2, wireless headphones by pressing the audio/select button (if equipped). • set home clock - pressing the select button allows you to set the clock. Turn the tune/scroll control knob to adjust the hours and then press and tur...

  • Page 224

    Subtitles — if equipped selecting this item allows you to choose between subtitle off or on. Audio drc — if equipped selecting this item allows you to limit maximum audio dynamic range. The default is set to 9high,9 and under this setting, dialogues will play at 11 db higher than if the setting is 9...

  • Page 225

    The set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am, 12 fm, and 12 satellite (if equipped) stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by press...

  • Page 226

    Note: the ignition switch must be in the on or acc position to operate the radio. Load button — loading compact disc(s) press the load button and the pushbutton with the corresponding number (1-6) where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After ...

  • Page 227

    Scan button (cd mode) press the scan button to scan through each track on the cd currently playing. Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd playe...

  • Page 228

    The radio uses the following limits for file systems: • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator 9.9 and a three- character extension) • level 2: 31 ...

  • Page 229

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling fre- quency (khz) bit rate (kbps) wma 44.1 and 48...

  • Page 230

    List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that...

  • Page 231

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) press the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxil...

  • Page 232

    Dolby t manufactured under license from dolby t laboratories. 9dolbyt9 and the double-d symbol are trademarks of dolby t laboratories. Macrovision this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyr...

  • Page 233

    Operating instructions — hands-free communication (uconnect t ) — if equipped refer to “hands-free communication (uconnect t)” in section 3. Clock setting procedure global positioning system (gps) — rer only the gps receiver used in this system is synchronized to the time data being transmitted by t...

  • Page 234

    2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “daylight savings.” touch the screen where the words “daylight savings” are dis- played to change the current setting. ...

  • Page 235

    Sales code res — am/fm stereo radio with cd player (mp3 aux jack) note: the radio sales code is located on the lower right side of your radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (...

  • Page 236

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. Time button press the time button and the time of day will display. In am or fm mode, press...

  • Page 237

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 238

    And 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to ...

  • Page 239

    Caution! • this cd player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • res is a single cd player. Do not attempt to insert a second cd if one is alrea...

  • Page 240

    Rw/ff press the rw button to stop the cd at the beginning of the current cd track/title. Press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm butt...

  • Page 241

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 242

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio l...

  • Page 243

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 244

    Number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for cana- dian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification...

  • Page 245

    Selecting satellite mode press the sat button until 9sat9 appears in the display. A cd may remain in the radio while in the satellite radio mode. Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around t...

  • Page 246

    Scan button (when equipped) pressing the scan button causes the tuner to search for the next channel, pausing for eight seconds before con- tinuing to the next. To stop the search, press the scan button a second time. Info button — except reu radio pressing the info button will cycle the display inf...

  • Page 247

    By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the prese...

  • Page 248

    Pushbutton memory. The channels stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stati...

  • Page 249

    Note: if you experience difficulty in playing a particu- lar disc, it may be damaged (i.E. Scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have theft protection encoding. Try a known good disc before considering disc player service. Radio operation and cellu...

  • Page 250

    Mode control the mode control allows you to choose from several pat- terns of air distribution as identified by the symbols. Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level air is directed through the panel and floor outlet...

  • Page 251

    Defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum fan and temperature settings for best windshield and side window defrosting. Blower control use this control (center rotary knob) to regulate the amount of air forced through the system in any...

  • Page 252

    Manual air conditioning and heating system — if equipped the controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. The instrument panel features four airflow reg...

  • Page 253

    Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level air is directed through the panel and floor outlets. Note: there is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to t...

  • Page 254

    Blower control use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the off position. Temperature control use this control to regulate the temperature of the air inside the passenger compart...

  • Page 255

    Note: continuous use of the “recirculate” mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. In cold or damp weather, the use of the “recirculate” mode will cause windows to fog on the inside because of moisture buildup inside the vehicle....

  • Page 256

    Max a/c for maximum cooling, select ei- ther the panel or bi-level position using the mode control. Then, press the “a/c” and the “recir- culate” buttons so that both lamps are illuminated, and set the tem- perature control to its coolest set- ting. Note: • recirculation mode will not operate in flo...

  • Page 257

    Smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer operation air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant...

  • Page 259: Starting And Operating

    Starting and operating contents m starting procedures . . . . . . . . . . . . . . . . . . . . 261 ▫ manual transmission . . . . . . . . . . . . . . . . . . 261 ▫ automatic transmission . . . . . . . . . . . . . . . . 261 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 261 ▫ extreme cold ...

  • Page 260

    M four–wheel drive operation (command-trac™ or rock-trac™) — if equipped. . . . . . . . . . . . . . . . . . . . . . . . . 274 ▫ operating instructions/precautions . . . . . . . . 274 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ shifting procedure . . . . . . . . . . . . . . ...

  • Page 261

    M anti-lock brake system . . . . . . . . . . . . . . . . . 299 m electronic brake control system . . . . . . . . . . . 301 ▫ abs (anti-lock brake system) . . . . . . . . . . . 301 ▫ tcs (traction control system) . . . . . . . . . . . 302 ▫ bas (brake assist system) . . . . . . . . . . . . . . 303 ▫ ...

  • Page 262

    M tire pressure monitor system (tpms) . . . . . . . 334 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . 337 ▫ general information . . . . . . . . . . . . . . . . . . . 339 m fuel requirements . . . . . . . . . . . . . . . . . . . . . 340 ▫ reformulated gasoline . . . . . . . . . . . . ...

  • Page 263

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat buildup may cause serious injury or death. Manual transmission apply ...

  • Page 264

    Tip start feature — automatic transmission only turn the ignition switch to start position and release it as soon as the starter engages. The starter motor will continue to run, but will automatically disengage itself when the engine is running. If the engine fails to start, the starter will disenga...

  • Page 265

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the veh...

  • Page 266

    If the engine shows no sign of starting after two 15 sec- ond periods of cranking with the accelerator pedal held to the floor, repeat the “normal starting” or “extreme cold weather” procedures. With tip start (automatic transmission only) if the engine fails to start after you have followed the “no...

  • Page 267

    Engine block heater — if equipped the engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three wire extension cord. The engine block heater cord is found under the hood bundled in fron...

  • Page 268

    Note: during cold weather, you may experience in- creased effort in shifting until the transmission fluid warms up. This is normal. Shifting fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. You should always use 1st gear ...

  • Page 269

    Manual transmission shift speeds in mph (km/h) en- gine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.8l accel. 15 (24) 24 (39) 34 (55) 47 (76) 56 (90) cruise 10 (16) 19 (31) 27 (43) 37 (60) 41 (66) downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when drivin...

  • Page 270

    Maximum recommended downshift speeds caution! Failure to follow the maximum recommended down- shifting speeds may cause the engine to overspeed and/or damage the clutch disc even if the clutch pedal is depressed. Manual transmission downshift speeds in mph (km/h) gear selec- tion 6 to 5 5 to 4 4 to ...

  • Page 271

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 272

    Brake/transmission interlock manual override your vehicle may be equipped with a shift lock manual override. The manual override may be used in the event that the shift lever should fail to move from park with the key in the on position and the brake pedal de- pressed. To operate the shift lock manu...

  • Page 273

    Automatic transmission with overdrive shifting from drive to park or reverse (or from p or r to d) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. Gear ranges do not race t...

  • Page 274

    Warning! (continued) • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or som...

  • Page 275

    When frequent transmission shifting occurs while using overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong head winds, or trailer towing), turning off over- drive will improve performance and extend transmission life by reducing excessive ...

  • Page 276

    Caution! • before moving the shift lever out of park, you must turn the ignition from lock so the steering wheel and shift lever are released. Otherwise, damage to steering column or shift lever could result. • never race the engine with the brakes on and the vehicle in gear, and never hold the vehi...

  • Page 277

    The transfer case is intended to be driven in the 2h position for normal street and highway conditions such as hard-surfaced roads. In the event that additional traction is required, the transfer case 4h and 4l positions can be used to lock the front and rear driveshafts together, forcing the front ...

  • Page 278

    When operating your vehicle in 4l, the engine speed will be approximately three times (four times for rubicon models) that of the 2h or 4h positions at a given road speed. Take care not to overspeed the engine. Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and c...

  • Page 279

    4h position this range locks the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This range (4h) provides additional traction for loose, slippery road surfaces and should not be used on wet or dry pavement. The 4wd indicator light (located in the i...

  • Page 280

    4h to 4l or 4l to 4h with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission into neutral (n), or de- press the clutch pedal on a manual transmission. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position...

  • Page 281

    Warning! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. Axle lock (tru–lok™) — rubicon models the axle lock switch is...

  • Page 282

    To activate the system, press the bottom of the axle lock switch once to lock the rear axle only (the rear axle lock indicator light will illuminate), press the bottom of the switch again to lock the front axle (the front axle lock indicator light will illuminate). When the rear axle is locked, pres...

  • Page 283

    The rear axle lock will disengage if the vehicle is taken out of 4l (low) range, or the ignition switch is turned to the off position. Electronic sway bar disconnect — if equipped your vehicle may be equipped with an electronic discon- necting stabilizer/sway bar. This system allows greater front su...

  • Page 284

    When activation conditions are not met. The stabilizer/ sway bar should remain in on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard surfaced roads or at speeds above 18 mph (29 km/h), you may lose control of the vehicle, which could result...

  • Page 285

    Warning! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your local au...

  • Page 286

    Off-road driving tips side step removal — if equipped note: prior to off-road usage, the side steps should be removed to prevent damage. 1. Remove two nuts from bodyside. 2. Remove one bolt from underside of vehicle. 3. Remove side step assembly. The basics of off-road driving you will encounter man...

  • Page 287

    Your vehicle’s steering, handling and traction. Control- ling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture. Avoid sudden accelerations, turns or braking. In most cases there are no road signs, pos...

  • Page 288

    Using light brake pressure with light throttle will keep the vehicle from jerking or lurching. This technique is also used when you need to stop and restart a vehicle on a steep incline. Driving in snow, mud and sand snow in heavy snow or for additional control and traction at slower speeds, shift t...

  • Page 289

    Entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck. Sand soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum a...

  • Page 290

    Forward until it makes contact with the object. Apply the throttle lightly while holding a light brake pressure and ease the vehicle up and over the object. Warning! Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle. Using a spotter th...

  • Page 291

    Vehicle’s mobility. Approach these obstacles at a 45- degree angle and let each tire go through the obstacle independently. You need to use caution when crossing large obstacles with steep sides. Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle ...

  • Page 292

    Of the high point when you let the vehicle down. You can also try rocking the vehicle or winching the vehicle off the object. Caution! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill climbing hill climbing requires good judgment and a good under- standin...

  • Page 293

    Slightly to bring all four tires back on the ground. As you approach the crest of the hill, ease off the throttle and slowly proceed over the top. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the steering wheel no more than...

  • Page 294

    Driving across an incline if at all possible avoid driving across an incline. If it is necessary, know your vehicle’s abilities. Driving across an incline places more weight on the downhill wheels, which increases the possibilities of a downhill slide or rollover. Make sure the surface has good trac...

  • Page 295

    Designated and approved. You should tread lightly and avoid damage to the environment. You should know your vehicles abilities and be able to recover it if some- thing goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intak...

  • Page 296

    Soft bottoms the vehicle will sink in, effectively increas- ing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross crossing puddles, pools, flooded areas or other standing water puddles, pools, flooded or other standing water areas nor...

  • Page 297

    The slowest current can push the heaviest vehicle down- stream out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obstacles...

  • Page 298

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, brake ro- tors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You...

  • Page 299

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature an...

  • Page 300

    Parking brake note: this vehicle is not equipped with a self- adjusting parking brake system. Refer to the “mainte- nance schedule” in section 8 of this manual for proper maintenance intervals. To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with ...

  • Page 301

    The load on the transmission locking mechanism may make it difficult to move the shifter out of park. Warning! • always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also, be certain to leave an automatic transmission in park, a manual transmis...

  • Page 302

    Warning! Significant over or under-inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The anti-lock brake system conducts a low speed self- test at about 12 mph (20 km/h). If for any reason, your foot is on the brake when the vehicle reac...

  • Page 303

    Warning! (continued) • the abs cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydro- planing. Only a safe, attentive, and skillful driver can prevent accidents. • the capabilities of an abs-equipped vehicle must never be e...

  • Page 304

    Help avoid skidding on slippery surfaces during braking. Refer to “anti-lock brake system” in section 5 of this manual for more information about abs. Warning! Abs (anti-lock brake system) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforde...

  • Page 305

    Bas (brake assist system) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 306

    Brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to amount of throttle applied as the vehicle starts to move in the intended di...

  • Page 307

    The system will only work if the intended direction of the vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is in drive (automatic transmission equipped vehicle), and the activation criteria are met, hsa will activate. Hsa on automatic trans...

  • Page 308

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision wi...

  • Page 309

    3. With the engine running, the brake applied, and the clutch out, rotate the steering wheel 180° counterclock- wise from center. 4. Press esp off switch four times within twenty sec- onds. 5. Rotate the steering wheel 360° clockwise (180° clock- wise from center). 6. Cycle ignition switch off then ...

  • Page 310

    Note: anytime the esp system is in the “full off” mode, erm is disabled. Refer to esp (electronic stability program) for a complete explanation of the available esp modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift o...

  • Page 311

    • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for the steering wheel position. The esp/tcs indicator light (located in the instrument cluster), starts to flash as soon as the tires los...

  • Page 312

    4h range (4wd models) or 2wd models on this is the normal operating mode for esp in 4h and 2wd vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4l range or neutral back to 4h range, the esp system will be in this mode. This mode should be used for most all...

  • Page 313

    Mode by pressing the esp off switch. Once the situation requiring esp to be switched to the “partial off” mode is overcome, turn esp back on by momentarily depressing the esp off switch. This may be done while the vehicle is in motion. Esp off (4h range only) this mode is intended for off-highway or...

  • Page 314

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” esp mode is intended for off-road use only. 4l range (4wd models) es...

  • Page 315

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” mode is intended for off- road use only. Disabling esp for modified ...

  • Page 316

    The following procedure will disable (or re-enable) esp functionality in the vehicle. 1. Shift the transfer case into the 4h range position. 2. Turn the steering wheel until it is centered and the wheels are pointed straight ahead. 3. Cycle the ignition key off to on. 4. Wait approximately five seco...

  • Page 317

    If the esp/bas warning light comes on continuously with the engine running, a malfunction has been detected in either the esp or the bas system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see...

  • Page 318

    Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Tire safety information tire markings 1 — u.S. Dot safety stan- dards code (tin) 4 — maximum load 2 — size designation 5 — maximum pressure 3 — se...

  • Page 319

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 320

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards (....Blank....( = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 321

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 322

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 323

    Tire loading and tire pressure tire placard location tire placard location (two-door models) tire placard location (four-door models) starting and operating 321 5.

  • Page 324

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 325

    Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx kg or xxx lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined...

  • Page 326

    324 starting and operating.

  • Page 327

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 328

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. Always drive with each tire properly inflated. Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abno...

  • Page 329

    Tire pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated e...

  • Page 330

    Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage especial...

  • Page 331

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 332

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators ...

  • Page 333

    Warning! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep unmounted tires in a cool, dry place with as l...

  • Page 334

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 335

    Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your autho- rized dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration...

  • Page 336

    These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on on/off road type tires. Rotation will increase tread life, help to main- tain mud, snow, and wet traction levels, and contribute to a smooth, qu...

  • Page 337

    Will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after a vehicle has not been driven for more than three hours, or driven less than 1 mile (1 km) after a three hour period. Refer to the “tires — general informa- tion” in th...

  • Page 338

    Monitoring telltale light will turn off only after the tires have been inflated to the vehicle’s recommended cold placard pressure value. Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicl...

  • Page 339

    • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tire pressure monitoring telltale light. • seasonal temperature changes will affect ...

  • Page 340

    Inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The system will automatically update and the tire pressure monitoring telltale light will extinguish once the updated tire pressures have been received. The vehicle may ne...

  • Page 341

    Tire pressure monitoring telltale light as long as none of the road tires are below the low pressure warning thresh- old. Note: if your vehicle is not equipped with a matching full-size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The tpms will...

  • Page 342

    The tire pressure sensors are covered under one of the following licenses: united states . . . . . . . . . . . . . . . . . . . . . Kr5s120123 canada . . . . . . . . . . . . . . . . . . . . . . . . 2671-s120123 fuel requirements all engines (except 5.7l engines) are de- signed to meet all emissions r...

  • Page 343

    The manufacturer supports the use of reformulated gaso- line. Properly blended reformulated gasoline will pro- vide excellent performance and durability for the engine and fuel system components. Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% etha...

  • Page 344

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory more extensive repairs will be required for prolo...

  • Page 345

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance, and damage the emission control system. • an out-of-tune engine, or certain fuel or ignition...

  • Page 346

    • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engi...

  • Page 347

    Loose fuel filler cap message (gascap) after fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged. If the system detects a malfunction, the “gascap” message will display in the odometer display. Tighten the gas ca...

  • Page 348

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and will cause the malfunction indicator light to turn on. Note: tight...

  • Page 349

    Included on this label and indicates the month, day, and hour of manufacture. The bar code that appears on the bottom of the label is your vin. Gross vehicle weight rating (gvwr) the gvwr is the total permissible weight of your vehicle including driver, passengers, vehicle, options, trailer tongue w...

  • Page 350

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 351

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully re- view this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow ...

  • Page 352

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Trailer tongue weight (tw) the trailer tongue weight is the downward force exerted on the...

  • Page 353

    Also dampens sway caused by traffic and crosswinds, and contributes positively to tow vehicle and trailer stability. Trailer sway control and a weight-distributing (load-equalizing) hitch are recommended for heavier tongue weights (tw) and may be required depending on vehicle and trailer configurati...

  • Page 354

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8...

  • Page 355

    3.8l/manual 4.10 2–door rubicon model (4wd) 6,236 lbs (2 829 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/automatic 4.10 2–door rubicon model (4wd) 6,281 lbs (2 849 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/manual 3.21 4–door x model (2wd) 5,121 lbs (2 323 ...

  • Page 356

    3.8l/manual 3.21 4–door sahara model (4wd) 5,481 lbs (2 486 kg) 32 sq ft (2.97 sq m) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/manual 3.73 4–door sahara model (4wd) 7,981 lbs (3 620 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/automatic 3.73 4–door sahara model (4wd) 8,027 lbs (...

  • Page 357

    Which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. Consider the following items when computing the weight on the rear axle of the vehicle: • the trailer tongue weight. • the weight of any other type of cargo or e...

  • Page 358

    Note: trailer towing requires special rear axle lubri- cant. Refer to “fluids, lubricants, and genuine parts” in section 7 for the correct fluid type. Caution! • avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may dam- age your vehicle. Warning! Improper towing...

  • Page 359

    • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in park. With a manual transmission, shift the transmis- sion into 1st gear. And with four-wheel-drive vehicles, make sure the transfer case ...

  • Page 360

    − when replacing tires, refer to “tires–general informa- tion” in this section for proper tire replacement proce- dures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s gvwr and gawr limits. Towing requirements — trailer brakes − do not interconnect the hydraulic...

  • Page 361

    Warning! (continued) towing any trailer will increase your stopping dis- tance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident. Towing requirements — trailer lights & wiring whenever you pull a trai...

  • Page 362

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in 1st gear to avoid excessive clutch slippage. Towing tips — automatic transmission the driv...

  • Page 363

    − when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − use speed control in flat terrain and with light loads to maximize fuel efficiency. Towing tips — cooling system to reduce potential for engine and trans...

  • Page 364

    Towing – 4wd models note: the transfer case must be shifted into n (neu- tral) for recreational towing. Shifting into neutral (n) use the following procedure to prepare your vehicle for recreational towing. Caution! It is necessary to follow these steps to be certain that the transfer case is fully ...

  • Page 365

    Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in n (neutral) and the engine running. With the trans- fer case in n (neutral) ensure that the engine is off prior to shifting the transmission into park (refer to steps 8 – 9 above). Shif...

  • Page 366

    Caution! • do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. 364 starting and operating.

  • Page 367: Contents

    What to do in emergencies contents m hazard warning flasher . . . . . . . . . . . . . . . . . 366 m if your engine overheats . . . . . . . . . . . . . . . . 366 m jacking and tire changing . . . . . . . . . . . . . . . 368 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 368 ▫ spare tir...

  • Page 368

    Hazard warning flasher the hazard warning flasher switch is located on the lower switch bank below the climate controls. Press the switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers. This is an emergency warn...

  • Page 369

    Note: there are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the a/c removes this heat. You can also turn the temperature control to maximum heat, t...

  • Page 370

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 371

    Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (2...

  • Page 372

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • block the wheel diagonally opposite the wheel to...

  • Page 373

    1. Remove spare tire, jack and tools from stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools. Connect jack handle driver to extension, then to lug wrench. 4. Operate jac...

  • Page 374

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position spare wheel/tire on vehicle and install lug ...

  • Page 375

    Jump starting if the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. Warning! • battery fluid is a corrosive acid solut...

  • Page 376

    4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. Warning! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could ...

  • Page 377

    Warning! (continued) • do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • during cold weather when temperatures are be- low freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump st...

  • Page 378

    Towing a disabled vehicle the manufacturer recommends towing with all four wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the other end on a towing dolly. 376 what to do in emergencies.

  • Page 379: Maintaining Your Vehicle

    Maintaining your vehicle contents m engine compartment – 3.8l . . . . . . . . . . . . . . 379 m onboard diagnostic system — obd ii . . . . . . . 380 ▫ loose fuel filler cap message . . . . . . . . . . . 380 m emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 380

    ▫ automatic transmission . . . . . . . . . . . . . . . . 398 ▫ hydraulic clutch fluid — manual transmission . . . . . . . . . . . . . . . . . . . . . . . . 401 ▫ manual transmission . . . . . . . . . . . . . . . . . . 401 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 402 ▫ front/rear...

  • Page 381

    Engine compartment – 3.8l 1 — integrated power module 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — automatic transmission dipstick 9 — air cleaner filter 4 — engine oil fill 10 — coolant pressure cap 5 — engine oil dipstick 11 — power steering fluid reservoir 6 — brake flu...

  • Page 382

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 383

    Gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the “malfunction indi...

  • Page 384

    5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 385

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any pro...

  • Page 386

    Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Always maintain the oil level within the safe zone on the dipstick. Adding 1 u.S. Quart (0.95l) of oil when the reading is at the bottom of the safe zone will result in a reading at the top of ...

  • Page 387

    The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “engine compart- ment” in this section. Lubricants which do not have both, the engine oil certi- fication mark and the correct sae viscosity grade nu...

  • Page 388

    Engine air cleaner filter refer to the “maintenance schedule” in section 8 for proper maintenance intervals. Warning! The air cleaner can provide protection in the case of engine backfire. Do not remove the air cleaner unless it is necessary for repair or maintenance. Make sure that no one is near t...

  • Page 389

    Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. Also, if a “fast charger” is ...

  • Page 390

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers ...

  • Page 391

    Remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield and rear window washers the fluid reservoir for the windshield washers and the rear window washer (if equipped) is shared. The fluid reservoir is locate...

  • Page 392

    Into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required. The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the converter as an emission...

  • Page 393

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situati...

  • Page 394

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 395

    Cooling system — drain, flush, and refill if the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant ...

  • Page 396

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol based engine coolant (anti- freeze). Use of propylene glycol base engine cool- ant (antifreeze) is not recommended. Adding engine coolant your vehicle has been built with an improved engine coolant (antifreeze) t...

  • Page 397

    Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that ...

  • Page 398

    To remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Engine coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and warm to normal o...

  • Page 399

    • check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • if frequent engine coolant (antifreeze) additions are required, or if ...

  • Page 400

    Warning! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency....

  • Page 401

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 402

    Note: if it is necessary to check the transmission below the operating temperature, the fluid level should be between the two cold (lower) holes on the dipstick with the fluid at approximately 70° f (21° c) (room tempera- ture). If the fluid level is correctly established at room temperature, it sho...

  • Page 403

    Hydraulic clutch fluid — manual transmission the clutch hydraulic system is a sealed maintenance free system. In the event of leakage or other malfunction, the system must be replaced. Manual transmission selection of lubricant use only manufacturer’s recommended manual trans- mission fluid. Refer t...

  • Page 404

    Transfer case fluid level check the fluid level should be to the bottom edge of the fill hole (a) when the vehicle is in a level position. Adding fluid fluid should be added only at filler hole until fluid begins to run out of the hole. Drain first remove fill plug (b), then drain plug (c). Recom- m...

  • Page 405

    Adding fluid add lubricant only at the fill hole and only to the level specified above. Selection of lubricant use only manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in this section for the correct fluid type. Maintenance after off-road driving after extended ope...

  • Page 406

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons,...

  • Page 407

    • use mopart cleaner wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! • do not use abrasive or strong cleaning materials such ...

  • Page 408

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider installing mud or stone shields behind each wheel. • use mopart touch-up paint on scratches or chips as so...

  • Page 409

    Interior care use mopar t total clean to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar t total clean, then mopar t spot & stain remover if absolutely necessary. Do not use harsh cleaners or armorall. Use mopar t total clean...

  • Page 410

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 411

    • be especially careful when washing the windows by following the directions for “care of fabric top windows.” washing — use mopar t car wash or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use mopar t convertible cloth top cleaner or a mild foaming ...

  • Page 412

    Even normal on-road driving and vehicle washing will eventually impact window zipper operation. To maintain ease of use of the window zippers, each window zipper should be cleaned and lubricated regularly. Use mo- par t soft top zipper cleaner and lubricant to ease zipper operation. Before applying,...

  • Page 413

    Cavity cartridge fuse mini fuse description j1 — — j2 30 amp pink transfer case module j3 — — cavity cartridge fuse mini fuse description j4 25 amp natural driver door node j5 25 amp natural passenger door node j6 40 amp green anti-lock brake sys- tem (abs) pump feed/esp j7 30 amp pink anti-lock bra...

  • Page 414

    Cavity cartridge fuse mini fuse description j11 30 amp pink sway bar j13 60 amp yellow ignition off draw (iod) — main j14 40 amp green ebl (rear window defogger) j15 30 amp pink rear blower j17 40 amp green starter solenoid j18 20 amp yellow powertrain control module (pcm) trans range j19 60 amp yel...

  • Page 415

    Cavity cartridge fuse mini fuse description m7 20 amp yellow power outlet #2 (batt/acc select) m8 20 amp yellow front heated seat m9 20 amp yellow rear heated seat (if equipped) m10 20 amp yellow ignition off draw — vehicle entertainment system (iod-ves), satellite digital audio receiver (sdars), dv...

  • Page 416

    Cavity cartridge fuse mini fuse description m15 20 amp yellow col mod, ir sns, heater ventilation, air conditioning/ automatic tempera- ture control (hvac/ atc), rear view mirror (rr vw mir), cabin compartment node (ccn), transfer case switch (t-case sw), run/st, multi- function control switch (mult...

  • Page 417

    Cavity cartridge fuse mini fuse description m22 10 amp red right horn (rt horn (hi/low) m23 10 amp red left horn (lt horn (hi/low) m24 25 amp natural rear wiper (rear wiper) m25 20 amp yellow fuel pump (fuel pump), diesel lift pump (dsl lift pump) — export only m26 — — m27 10 amp red ignition switch...

  • Page 418

    Cavity cartridge fuse mini fuse description m34 10 amp red park assist (prk asst), heater venti- lation, air condition- ing module (hvac mod), headlamp wash (hdlp wash), compass (compas) m35 10 amp red heated mirrors m36 20 amp yellow power outlet m37 10 amp red anti-lock brake sys- tem (abs), elect...

  • Page 419

    Caution! (continued) • when replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem i...

  • Page 420

    Exterior lights bulb type backup lights (2). . . . . . . . . . . . . . . . . . . . . . . . 3157 center high-mounted stop light (1) . . . . . . . . . L.E.D. Fog lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9145 front park/turn lights (2) . . . . . . . . . . . . . . . . . 3157 front...

  • Page 421

    6. Remove the lamp from the collar. 7. Grasp the bulb and turn 1/4 turn counterclockwise. 8. Pull the bulb from the housing. 9. Push connector locking tab to the unlock position. 10. Remove connector from bulb. 11. Push connector onto new bulb base, and push the connector locking tab to the lock pos...

  • Page 422

    Front fog light 1. Locate the front fog lamp in the front fascia, and disconnect the electrical connector from underneath. 2. Turn the bulb 1/4 turn counterclockwise. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact...

  • Page 423

    Center high-mounted stop light (chmsl) the stop lamp is mounted on a bracket that extends upward from the tailgate behind the spare tire. If service is needed, obtain the led/cover assembly from your local authorized dealer. 1. Remove the spare tire. 2. Remove the four screws holding the lens/cover ...

  • Page 424

    Fluid capacities u.S. Metric fuel (approximate) — 2–door models 18.5 gallons 70 liters fuel (approximate) — 4–door models 22.5 gallons 85 liters engine oil with filter 3.8 liter engine (sae 5w-20, api certified engine oil) 6 quarts 5.7 liters cooling system * 3.8 liter engine (mopar t antifreeze/eng...

  • Page 425

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar t antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chrysler material sta...

  • Page 426

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar t atf+4 automatic transmission fluid manual transmission mopar t manual transmission lubricant or equivalent (meeting the require- ments of chrysler material standard ms-9224) transfer case mopar t atf+4 automatic trans...

  • Page 427: Maintenance Schedules

    Maintenance schedules contents m emissions control system maintenance . . . . . . 426 m maintenance schedule . . . . . . . . . . . . . . . . . . 426 ▫ required maintenance intervals . . . . . . . . . . 428 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 428

    Emissions control system maintenance the scheduled maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the emissions con- trol system. These, and all other maintenance services included in this manual, should be done...

  • Page 429

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Your dealer will reset the oil change indicator message after completing the ...

  • Page 430

    Once a month • check tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • check all lights and other electri...

  • Page 431

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 432

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # dea...

  • Page 433

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your veh...

  • Page 434

    36,000 miles (60,000 km) or 36 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 435

    48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 436

    60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings, replace if necessary. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ ch...

  • Page 437

    72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings,...

  • Page 438

    84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings,...

  • Page 439

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings,...

  • Page 440

    114,000 miles (190,000 km) or 114 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 438 maintenance schedules 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 441

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace accessory drive belt(s). ❏ inspect the brake linings, replace if necessary. ❏ adjust parking brake on vehicles equip...

  • Page 442

    126,000 miles (210,000 km) or 126 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # ...

  • Page 443

    144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake lining...

  • Page 444

    150,000 miles (250,000 km) or 150 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your ...

  • Page 445

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about y...

  • Page 447: Contents

    If you need consumer assistance contents m suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447 ▫ prepare for the appointment . . . . . . . . . . . . 447 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . 447 ▫ be reasonable wi...

  • Page 448

    M publication order forms . . . . . . . . . . . . . . . . . 451 m department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 452 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . 453 ▫ traction grades . . . . . . . . . . . . . . . . . . . ....

  • Page 449

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 450

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 451

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 452

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear con...

  • Page 453

    To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administrator, nhtsa, 400 seventh street, sw., wash- ington, d.C. 20590. You can also obtain other information about motor vehicle safety f...

  • Page 454

    • diagnostic procedure manuals diagnostic procedure manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features. They show exactly how to find...

  • Page 455

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relativ...

  • Page 456

    Vehicle safety standard no. 109. Grades b and a repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law. Warning! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflati...

  • Page 457: Index

    Index 10

  • Page 458

    Abs (anti-lock brake system) . . . . . . . . . . . . 201,299 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 190 air cleaner, engine (engine air cleaner filter) . . . 386 air conditioner maintenance . . . . . . . . ....

  • Page 459

    Axle lock . . . . . . . . . . . . . . . . . . . . . . . . . . 279,280 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 emergency starting . . . . . . . . . . . . . . . . . . . . . 373 keyless transmitter replacement (rke) . . . . . . . 24 belts, seat . . . . . . . . . . . . ...

  • Page 460

    Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 247 clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 216,231,234 compact disc (cd) maintenance . . . . . . . . . . . . . 246 compass . . . . . . . . ...

  • Page 461

    Disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 used coolant (antifreeze) . . . . . . . . . . . . . . . . 395 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 driver’s seat...

  • Page 462

    Fuel requirements . . . . . . . . . . . . . . . . . . 340,422 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . 373 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383,422 oil disposal . . . . . . . . . . . . . . . . . . . . . . . . . . 385 oil filter . . . . . . . . . ...

  • Page 463

    Fold and tumble rear seat . . . . . . . . . . . . . . . . . . 89 folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . 92 folding windshield . . . . . . . . . . . . . . . . . . . . . . 183 four wheel drive . . . . . . . . . . . . . . . . . . . . . . . 274 shifting . . . . . . . . . . . ....

  • Page 464

    Hard top, modular . . . . . . . . . . . . . . . . . . . . . . 115 hard top removal . . . . . . . . . . . . . . . . . . . . . . . 118 hazard warning flasher . . . . . . . . . . . . . . . . . . . 366 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 89 head rests . . . . . . . . . . ...

  • Page 465

    Jacking instructions . . . . . . . . . . . . . . . . . . . . . . 370 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . 373 key, programming . . . . . . . . . . . . . . . . . . . . . . . . 16 key, replacement . . . . . . . . . . . . . . . . . . . . . . . . 15 key, sentry (immobilizer)...

  • Page 466

    Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 418 high beam . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 high beam indicator . . . . . . . . . . . . . . . . . . . . 199 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 96 interior . . . . . . . . . . . . ...

  • Page 467

    Fluid level check . . . . . . . . . . . . . . . . . . . . . . 401 lubricant selection . . . . . . . . . . . . . . . . . . . . . 401 shift speeds . . . . . . . . . . . . . . . . . . . . . . . . . . 266 master cylinder (brakes) . . . . . . . . . . . . . . . . . . 398 mini-trip computer . . . . . . . ....

  • Page 468

    Owner’s manual (operator manual) . . . . . . . . . 6,451 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 paint damage . . . . . . . . . . . . . . . . . . . . . . . . . . 404 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 parking brake . . . . . . . . ...

  • Page 469

    Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388 release, hood . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 reminder, lights on . . . . . . . . . . . . . . . . . . . . . . 96 reminder, seat belt . . . . . . . . . . . . . . . . . . . . . . . 48 remote control door l...

  • Page 470

    Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 fold and tumble re...

  • Page 471

    Automatic transmission . . . . . . . . . . . . . . . . . 261 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . 262 engine block heater . . . . . . . . . . . . . . . . . . . . 265 engine fails to start . . . . . . . . . . . . . . . . . . . . 262 manual transmission . . . . . . . . . . . ...

  • Page 472

    High speed . . . . . . . . . . . . . . . . . . . . . . . . . . 328 inflation pressures . . . . . . . . . . . . . . . . . . . . . 326 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 368,371 load capacity . . . . . . . . . . . . . . . . . . . . . 321,322 pressure monitor system (tpms) . ...

  • Page 473

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 402 transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 maintenance . . . . . . . . . . . . . . . . . . . . . . . 398,401 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 range indicator ...

  • Page 474

    Wheel and wheel trim . . . . . . . . . . . . . . . . . . . . 406 wheel and wheel trim care . . . . . . . . . . . . . . . . 406 wheel mounting . . . . . . . . . . . . . . . . . . . . . . . . 372 wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . . . 38 window fogging . . . . . . . . . . ....

  • Page 475

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 476

    121413 09 wrangler om.Indd 1 121413 09 wrangler om.Indd 1 3/11/08 9:26:49 am 3/11/08 9:26:49 am.